The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System)
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System)
G3834
1.REMOVE SERVICE PLUG GRIP
82111
2.DISCONNECT ENGINE ROOM MAIN WIRE
Be sure to wear insulated gloves.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector.
Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
Insulate the disconnected terminals with insulating tape.
Do not touch the waterproof seal or terminals of the connector.
3.REMOVE CONNECTOR COVER ASSEMBLY
4.CHECK TERMINAL VOLTAGE
5.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY
821H1
6.DISCONNECT HV FLOOR UNDER WIRE
73350C
7.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
for Fold Down Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL
for Reclining Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
8.REMOVE REAR SEAT CUSHION ASSEMBLY
for Fold Down Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL
for Reclining Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
72693
9.REMOVE REAR SEAT CUSHION LOCK HOOK
for Fold Down Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fold Down Seat Type)>REMOVAL
for Reclining Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
67918A
10.REMOVE REAR DOOR SCUFF PLATE LH
76974F
11.REMOVE REAR UNDER SIDE COVER LH
67917A
12.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
76973F
13.REMOVE REAR UNDER SIDE COVER RH
76971G
14.REMOVE REAR UNDER COVER
71033
15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
G92N4A
16.REMOVE NO. 1 HV BATTERY COVER PANEL RH
821H1
17.DISCONNECT HV FLOOR UNDER WIRE
Be sure to wear insulated gloves.
| *a | Shield Ground |
Disconnect the 2 HV battery junction block assembly connectors.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Disconnect the shield ground from the HV battery.
Disconnect the floor wire connector.
17410
18.REMOVE FRONT EXHAUST PIPE ASSEMBLY
17141
19.REMOVE EXHAUST MANIFOLD
58398F
20.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)
58223
21.REMOVE CENTER NO. 2 FLOOR HEAT INSULATOR
Remove the 3 nuts and center No. 2 floor heat insulator.
33820B
22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the 2 nuts and disconnect the transmission control cable assembly.
821H1
23.REMOVE HV FLOOR UNDER WIRE
Be sure to wear insulated gloves.
Insulate the disconnected connectors with insulating tape.
Remove the 2 nuts.
Remove the 2 clamps.
If the clamps are removed forcibly, the stud bolts may be damaged.
Disengage the grommet and pull out the HV floor under wire from the floor panel hole.
Remove the 3 nuts.
Remove the 2 nuts and clamp.
If the clamp is removed forcibly, the stud bolt may be damaged.
Disengage the clamp.
Disconnect the HV floor under wire connector.
Remove the nut and HV floor under wire.