Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY › 2019.02–2021.02
RM33C0E _58 Vehicle Interior _065463 SEAT BELT _0332572 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 73350C 4.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

Hide 5.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

Hide 72693 6.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Hide 62332A 7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)

Hide 8.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

Hide 62331A 9.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)

HINT:

Use the same procedure as for the LH side.


Hide 10.REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:

Use the same procedure as for the LH side.


Hide 11.REMOVE REAR SEAT ASSEMBLY (for Reclining Seat Type)

Hide 62472A 12.REMOVE INNER ROOF SIDE GARNISH LH

Hide 62471A 13.REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73370E 14.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH

a.
B470181

Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly LH.


Hide 73360D 15.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81006 16.REMOVE CENTER STOP LIGHT SET

Hide 73373F 17.REMOVE REAR SEAT SHOULDER BELT HOLE COVER

a.
B470184

Disengage the 2 claws and 2 guides to remove the rear seat shoulder belt hole cover.

HINT:

Use the same procedure for the other rear seat shoulder belt hole covers.



Hide 64330 18.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

a.

Fold the rear seatback assembly LH and rear seatback assembly RH forward.


b.
B470185

Remove the 2 clips.


c.
B472991

Disengage the 3 clips and 5 guides.


d.

Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.


Hide 64330 19.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

a.
B484986

Disengage the 3 clips.


b.

Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.


Hide 73370E 20.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

a.
B471060C01
1,0.573 1.219,0.5 true 1.198,0.76 1.396,0.729 true 1.25,0.396 1.479,0.594 0.229,0.198 10 false *b 1.417,0.656 1.656,0.865 0.24,0.208 10 false *a 0.677,0.177 0.99,0.396 0.313,0.219 10 false *c
*a Protective Tape
*b Locking Button
*c Release


Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.



b.
B471062

Remove the 2 bolts.


c.

Disengage the guide to remove the rear seat outer belt assembly LH.


Hide 73360D 21.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73432 22.REMOVE REAR SEAT BELT RETRACTOR COVER

a.
B471063C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear seat belt retractor cover as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.