Home › Suspension › REAR SUSPENSION › REAR LOWER ARM › 2019.02–2021.02
RM33C0E _53 Suspension _065439 REAR SUSPENSION _0331924 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48720A 1.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.

Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly and rear suspension member sub-assembly with the 2 bolts and 2 nuts.

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Insert the bolt with the threaded end facing the rear of the vehicle.




Hide 48740F 2.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and nut.

NOTICE:
·

Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle.

·

When tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.




Hide 48258C 3.INSTALL REAR LOWER COIL SPRING INSULATOR

Hide 48231B 4.INSTALL REAR COIL SPRING

Hide 48840A 6.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 48720A 7.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.
C375458

Install the rear No. 1 suspension arm assembly with the 2 bolts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48740F 8.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.
C376668

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 89408C 9.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 10.INSTALL REAR WHEEL

Hide 48740F 11.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Lower the vehicle to the ground.


b.

Bounce the vehicle up and down at the corners to stabilize the rear suspension.


c.
C370199C01
1.865,0.74 2.146,0.74 true 1.865,1.115 1.865,0.688 1.865,0.688 2.156,0.688 true 1.031,1.688 1.031,1.396 1.031,1.396 0.844,1.396 true 0.813,1.469 1.031,1.469 true 1.802,1.115 1.99,1.344 0.188,0.229 10 true *a 0.958,1.688 1.146,1.917 0.188,0.229 10 true *a
*a Matchmark


Align the matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.


d.

Fully tighten the nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:
·

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

·

Make sure that the vehicle is unloaded when fully tightening the nut.




Hide 12.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 13.PERFORM INITIALIZATION

Parking Support Brake System (Click here)
Parking assist monitor system (Click here)
Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)