The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>PRECAUTION
2.REMOVE REAR WHEEL
3.PERFORM REAR BRAKE PAD REPLACEMENT MODE
4.DISABLE BRAKE CONTROL
Wait at least 2 minutes after turning the power switch off.
When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.
Do not operate the electric parking brake switch assembly when the electric parking brake system is in rear brake pad replacement mode.
Disconnect the reservoir level switch connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal cannot be further depressed.
5.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
47319F
6.SEPARATE REAR FLEXIBLE HOSE
Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.
890C0A
7.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
46310B
8.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY
47850
9.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY
| *a | Turn |
| *b | Hold |
Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.
04466
10.REMOVE REAR DISC BRAKE PAD
Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.
04946
11.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT
12.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE
Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.
Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.
13.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN
| *1 | Rear No. 1 Disc Brake Cylinder Slide Pin |
| *2 | Rear No. 2 Disc Brake Cylinder Slide Pin |
Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.
Do not damage the rear No. 2 disc brake cylinder slide pin.
47775D
14.REMOVE REAR DISC BRAKE BUSHING DUST BOOT
Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.
47822
15.REMOVE REAR DISC BRAKE CYLINDER MOUNTING
Remove the 2 bolts and rear disc brake cylinder mounting.
42431
16.REMOVE REAR DISC
| *a | Matchmark |
Put matchmarks on the rear disc and rear axle hub and bearing assembly.
Remove the rear disc.