Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for RHD) › 2019.02–2021.02
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319354 BRAKE BOOSTER PUMP(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)

CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE FRONT WHEEL LH

Hide 55708 3.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 4.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 5.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide 6.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 44572C 8.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C378001

Slide the clip and disconnect the No. 2 brake actuator hose from the No. 1 brake actuator tube.


Hide 44551C 9.SEPARATE NO. 1 BRAKE ACTUATOR TUBE

a.
C378038

Remove the nut and separate the No. 1 brake actuator tube from the vehicle body.


Hide 473A1 10.DISCONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C378003

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.




Hide 11.REMOVE BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.
C378023C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C378005C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.

Disengage the clamp and separate the engine room main wire.


d.
C378022C02
0.854,1.26 1.26,1.26 true 1.927,1.573 2.333,1.573 true 2.115,1.26 2.521,1.26 true 1.042,0.979 1.448,0.979 true 1.167,0.5 1.396,0.5 1.396,0.5 1.677,1.073 true 2.458,0.667 2.208,0.667 2.208,0.667 1.844,1.146 true 2.344,1.49 2.521,1.646 0.177,0.156 10 true *a 0.677,1.188 0.854,1.333 0.177,0.146 10 true *b 0.854,0.896 1.042,1.052 0.188,0.156 10 true *c 0.969,0.427 1.156,0.573 0.188,0.146 10 true *d 2.469,0.583 2.656,0.74 0.188,0.156 10 true *e 2.542,1.188 2.708,1.333 0.167,0.146 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


e.
C378007

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




f.
C378035

Using a union nut wrench, disconnect the front No. 5 brake tube while holding the front flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the front No. 5 brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front No. 5 brake tube from the connecting parts.




g.
C378009

Disengage the clamp and separate the front No. 5 brake tube.

NOTICE:

Do not kink or damage the front No. 5 brake tube.



h.
C378037

Move aside the front No. 5 brake tube as shown in the illustration.

NOTICE:

Do not apply excessive force to the front No. 5 brake tube.



i.
C378010

Disengage the clamp and remove the brake tube clamp.


j.
C378039

Remove the bolt and separate the front brake tube way from the vehicle body.


k.
C378040

Disengage the clamp and separate the No. 2 brake tube clamp from the vehicle body.

NOTICE:

Do not kink or damage the brake lines.



l.
C398980

Disengage the 5 clamps to remove the No. 2 brake tube clamp from the brake lines.

NOTICE:

Do not kink or damage the brake lines.



m.
C378011C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the vehicle body as shown in the illustration.


n.
C378012

Remove the 2 bolts.

HINT:

Insert the tool from the bottom of the vehicle.



o.
C378013

Remove the nut.


p.
C378057

Move aside the brake lines as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




q.

Remove the brake actuator with brake booster pump assembly as shown in the illustration.

C378058C01
2.156,0.969 2.156,0.729 true 1.74,0.729 1.74,0.302 1.74,0.302 1.469,0.302 true 1.302,0.24 1.469,0.385 0.167,0.146 10 true *1 2.083,0.969 2.271,1.115 0.188,0.146 10 true *a
*1 Brake Actuator Bracket Assembly - -
*a Cutout - -


NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

When removing the brake actuator with brake booster pump assembly, pass the brake actuator bracket assembly through the cutout in the vehicle body.



Hide 44572C 12.REMOVE NO. 2 BRAKE ACTUATOR HOSE

a.
C378016

Slide the clip and remove the No. 2 brake actuator hose from the brake booster pump assembly.


Hide 47070 13.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C378018

Disengage the claw and clamp to separate the brake booster pump assembly wire harness from the brake actuator bracket assembly.


b.
C378019

Remove the nut from the brake booster pump assembly.


c.
C378020C02
0.927,3.656 1.24,3.656 false 0.906,4.313 1.219,4.313 false 2.063,3.708 2.281,3.292 2.281,3.292 2.51,3.292 true 1.958,4.063 2.115,4.302 2.115,4.302 2.313,4.302 false 0.76,3.594 1.073,3.75 0.313,0.156 10 false *a 0.74,4.25 1.052,4.406 0.313,0.156 10 false *b 2.344,4.219 2.656,4.375 0.313,0.156 10 false *c 2.552,3.219 2.865,3.375 0.313,0.156 10 false *d
*a Union
*b Connector
*c Wire Harness
*d Stud


Remove the brake booster pump assembly, brake booster pump bushing and brake actuator case collar from the brake actuator bracket assembly.

NOTICE:
·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.




d.
C380035

Remove the 2 brake booster pump collars and 2 brake booster pump bushings from the brake booster pump assembly.

HINT:

Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.