Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2019.02
RM33C0E _54 Brake _065442 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1202  Master Reservoir Level Malfunction  


DESCRIPTION

If the skid control ECU (brake booster with master cylinder assembly) detects that the brake fluid level is low or there is an open in the brake fluid level warning switch signal circuit, DTC C1202 is stored.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1202 Master Reservoir Level Malfunction 1126 Either of the following is detected:
1.

The brake fluid level warning switch signal circuit is open for a certain period of time.

2.

The reservoir level is low for a certain period of time.


·

Open or short in brake fluid level warning switch (brake booster with master cylinder assembly)

·

Brake fluid leaks

·

Open or short in wire harness

·

Low brake fluid

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
HINT:

The DTC is cleared when the conditions return to normal.



DTC Detection Conditions: C1202 INF Code: 1126
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The brake fluid level warning switch signal circuit is open for a certain period of time. ○ -
The reservoir level is low for a certain period of time. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C345753E09
5,1.229 5.313,1.427 0.313,0.198 10 false 16 5.26,1.469 5.573,1.667 0.313,0.198 10 false LBL 4.927,2.958 5.24,3.156 0.313,0.198 10 false A40 4.917,3.146 6.979,3.521 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.052,1.219 4.365,1.417 0.313,0.198 10 false 2 3.698,1.229 4.01,1.427 0.313,0.198 10 false LBL 2.302,1.229 2.615,1.427 0.313,0.198 10 false GND 2.063,1.229 2.375,1.427 0.313,0.198 10 false 1 1.927,2.104 2.24,2.302 0.313,0.198 10 false A1 1.917,2.271 4.417,2.656 2.5,0.385 10 false Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly) 6.26,1.354 6.573,1.552 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1202 is output. A
DTC C120F is output with DTC C1202. B



A

2.CHECK BRAKE FLUID LEVEL

B

2.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster pump assembly, brake master cylinder reservoir assembly (brake booster with master cylinder assembly), brake booster with master cylinder assembly, and wheel cylinders).

HINT:

If no leaks exist, add and adjust fluid using the GTS.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION



ii.

Check the thickness of the brake pad lining.

for Front Brake (for 2-Pot Caliper): Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for 2-Pot Caliper)>INSPECTION

for Front Brake (except 2-Pot Caliper): Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (except 2-Pot Caliper)>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION

HINT:

If the thickness is less than the standard, replace the brake pads with new ones.




b.

Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


ii.

Turn the power switch off.


iii.

Disconnect the A39 brake pedal stroke sensor assembly connector.


iv.

Select the Data List on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MT Voltage Value MT voltage value Min.: 0.00 V, Max.: 20.00 V Pump motor off: 0.00 V
Pump motor on: 12.00 V
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 105 279,502

v.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


vi.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.



Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



A

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

B

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
a.
C230719C17
0.854,2.854 1.51,1.99 true 2.604,2.938 1.906,1.979 true 0.177,0.323 0.49,0.521 0.313,0.198 10 false *a 0.708,2.896 1.021,3.094 0.313,0.198 10 false LBL 2.563,2.969 2.875,3.167 0.313,0.198 10 false GND
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Reconnect the A39 brake pedal stroke sensor assembly connector.


c.

Remove the brake master cylinder reservoir filler cap assembly.


d.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



e.

Disconnect the A1 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the brake master cylinder reservoir assembly (brake booster with master cylinder assembly). Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (LBL) - 1 (GND) Brake fluid level warning switch (brake booster with master cylinder assembly) off (float up) 1.84 to 2.16 kΩ
2 (LBL) - 1 (GND) Brake fluid level warning switch (brake booster with master cylinder assembly) on (float down) Below 1 Ω
(Brake fluid level is low)


HINT:

If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the power switch on (IG).



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-16 (LBL) - A1-2 (LBL) Always Below 1 Ω
A40-16 (LBL) or A1-2 (LBL) - Body ground Always 10 kΩ or higher
A1-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)
a.
C230720C25
0.438,0.938 0.833,1.188 0.396,0.25 2.167,2.802 1.885,2.125 true 0.25,0.26 0.563,0.458 0.313,0.198 10 false *a 2.146,2.802 2.469,2.927 0.323,0.125 10 false LBL 0.563,0.969 0.875,1.167 0.313,0.198 10 false A1
*a Front view of wire harness connector
(to Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly))


Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A1-2 (LBL) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A1 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


c.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch off.


e.

Turn the power switch on (READY).


f.

Perform a road test.


g.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1202 is not output. A
DTC C1202 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY