Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › 2019.02–2020.08
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319553 OIL COOLER A

P710 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during motor cooling cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ steering control) (Click here)
Parking Support Brake System*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Vehicle Identification Number (VIN) or frame number registration MIL illuminates (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System)

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System)

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>REGISTRATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>REGISTRATION



PROCEDURE

Hide 53851M 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

Hide G9200 6.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G9225K 7.REMOVE NO. 1 INVERTER COOLING HOSE

a.
C381413

Slide the clip and remove the No. 1 inverter cooling hose from the motor cooling cooler.


Hide G9229A 8.DISCONNECT NO. 5 INVERTER COOLING HOSE

Hide G125A 9.REMOVE MOTOR COOLING COOLER

a.
C381414C01
1.927,0.24 2.073,0.24 2.073,0.24 2.24,0.479 true 1.125,0.604 1.271,0.604 1.271,0.604 1.438,0.844 true 1.698,0.177 1.906,0.354 0.208,0.177 10 true *1 0.896,0.542 1.125,0.719 0.229,0.177 10 true *2
*1 Oil Cooler Union Bolt
*2 No. 1 Oil Cooler Tube Clamp


Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


b.

Remove the bolt and No. 1 oil cooler tube clamp to disconnect No. 2 motor cooling pipe from the hose bracket.


c.
C381415

Remove the 3 bolts to disconnect the motor cooling cooler from the No. 1 transmission control cable bracket.


d.
C377456

Slide the clip and disconnect the No. 1 motor cooling hose from the transaxle housing tube connector.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.



Hide G1252A 10.REMOVE NO. 2 MOTOR COOLING PIPE

a.
C381416

Slide the clip and remove the No. 2 motor cooling pipe from the No. 2 motor cooling hose.

NOTICE:

Make sure not to remove the No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.