Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2019.10
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headlight ECU LH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headlight ECU LH Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "HL AutoLeveling/AFS/AHS" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "HL AutoLeveling/AFS/AHS" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "HL AutoLeveling/AFS/AHS" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Headlight ECU LH Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Headlight ECU sub-assembly LH branch line or connector

·

Power source circuit of headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH ground circuit

·

Headlight ECU sub-assembly LH



WIRING DIAGRAM

C421966E02
0.115,1.813 0.573,2.01 0.458,0.198 10 false K126 5.208,4.052 7.042,4.49 1.833,0.438 10 false Headlight ECU Sub-assembly LH 5.292,0.75 5.75,0.948 0.458,0.198 10 false 24 5.292,1.344 5.75,1.542 0.458,0.198 10 false 23 5.625,0.854 6.125,1.073 0.5,0.219 10 false CANH 1.667,1.344 2.125,1.542 0.458,0.198 10 false 19 1.698,0.75 2.156,0.948 0.458,0.198 10 false 8 5.615,2.469 6.073,2.667 0.458,0.198 10 false IG 5.615,3.063 6.073,3.26 0.458,0.198 10 false GND 0.51,1.813 2.75,2.104 2.24,0.292 10 false No. 3 CAN Junction Connector 5.302,2.958 5.76,3.156 0.458,0.198 10 false 12 5.333,2.354 5.792,2.552 0.458,0.198 10 false 4 3.729,2.333 4.865,2.583 1.135,0.25 10 false ECU-IG1 NO. 3 1.615,2.458 3.375,2.885 1.76,0.427 10 false from IG1-NO. 1 Relay 5.604,1.448 6.104,1.667 0.5,0.219 10 false CANL 4.875,4.052 5.333,4.25 0.458,0.198 10 false A78

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A78 headlight ECU sub-assembly LH connector.


c.
C346919C91
1.49,0.844 1.885,1.063 0.396,0.219 2.385,2.958 2.531,2.958 2.531,2.958 2.531,2.188 true 2.802,2.958 2.635,2.958 2.635,2.958 2.635,2.188 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.573,0.875 1.948,1.125 0.375,0.25 10 false A78 2.854,2.896 3.281,3.052 0.427,0.156 10 false CANH 2.021,2.906 2.448,3.063 0.427,0.156 10 false CANL
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A78-24 (CANH) - A78-23 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346919C92
1.49,0.844 1.885,1.063 0.396,0.219 0.677,2.958 0.823,2.958 0.823,2.958 0.823,2.188 true 1.99,1.188 1.802,1.188 1.802,1.188 1.802,2 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.563,0.875 1.99,1.25 0.427,0.375 10 false A78 2.052,1.115 2.479,1.271 0.427,0.156 10 false IG 0.313,2.896 0.74,3.052 0.427,0.156 10 false GND
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A78-12 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A78-4 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)