Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › from 2019.10
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319556 SHIFT LEVER A

P710 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

a.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


b.

Connect the shift lock control ECU connector.


c.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


d.

Connect the transmission control switch connector.


e.

Install the clip to the No. 1 console box duct.


f.
C380394N01
2.688,1.083 2.844,1.281 0.156,0.198 10 true 1 0.635,1.667 0.792,1.865 0.156,0.198 10 true 2 2.104,1.781 2.26,1.979 0.156,0.198 10 true 3 2.354,0.625 2.51,0.823 0.156,0.198 10 true 4

Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.


g.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.


a.
C400603C09
1.646,1.198 1.844,1.594 1.844,1.594 2,1.594 false 1.313,1.344 1.583,1.594 0.271,0.25 10 false *b 2.042,1.49 2.333,1.708 0.292,0.219 10 false *a
*a Adjuster Case Cover
*b Slide


Slide the adjuster case cover in the direction shown by the arrow.


b.
C400817C08
1.333,0.583 1.479,0.583 1.479,0.583 1.719,0.948 false 1.375,1.802 1.531,1.802 1.531,1.802 1.688,1.167 true 1.333,2.719 1.479,2.719 1.479,2.719 1.719,3.083 false 1.396,3.99 1.552,3.99 1.552,3.99 1.708,3.354 true 1.854,1.302 2.156,1.542 0.302,0.24 10 false *b 1.167,1.719 1.406,1.927 0.24,0.208 10 false *a 1.198,3.896 1.438,4.115 0.24,0.219 10 false *a 1.125,0.5 1.375,0.74 0.25,0.24 10 false *c 1.125,2.635 1.333,2.844 0.208,0.208 10 false *c
*a Lock Piece
*b Pull Out
*c Adjuster Case


Using a precision screwdriver, pull out the lock piece of the adjuster case.


c.
C377530C01
2.208,3.344 2.938,2.125 2.938,2.125 2.25,1.198 true 1.938,1.833 2.167,2.156 2.167,2.156 2.333,2.156 false 1.938,4.063 2.167,4.385 2.167,4.385 2.333,4.385 false 2.375,2.063 2.677,2.313 0.302,0.25 10 false *a 2.042,0.458 2.333,0.667 0.292,0.208 10 false *b 3,2.042 3.26,2.219 0.26,0.177 10 false *c 2.375,4.302 2.677,4.552 0.302,0.25 10 false *a
*a Lock Nut
*b Push in
*c Stopper


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


d.
C413142C01
0.458,0.25 0.646,0.25 0.646,0.25 0.854,0.521 false 2.26,0.229 2.448,0.229 2.448,0.229 2.615,0.417 false 0.26,0.167 0.49,0.375 0.229,0.208 10 false *a 2.021,0.146 2.25,0.333 0.229,0.188 10 false *a
*a Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:

After installation, check that the outer part of the stopper is as shown in the illustration.



e.
C413143

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the shift lever is in N.


·

Securely connect the end of the transmission control cable assembly to the transmission floor shift assembly.




f.
C413144C01
1.74,1.323 2.24,1.74 2.24,1.74 2.396,1.74 true 1.031,0.635 1.188,0.635 1.188,0.635 1.646,1.073 true 1.521,1.479 1.74,1.677 0.219,0.198 10 false *b 2.448,1.667 2.677,1.875 0.229,0.208 10 false *a 0.813,0.552 1.01,0.74 0.198,0.188 10 true *c
*a Lock Piece
*b Push in
*c Adjuster Case


Push in the lock piece of the adjuster case to lock it.


g.
C413145C01
0.99,1.792 1.115,1.792 1.115,1.792 1.406,1.375 true 1.042,4.271 1.198,4.271 1.198,4.271 1.51,3.813 true 2.156,4.292 2,4.292 2,4.292 1.729,3.729 true 0.792,1.698 1.063,1.917 0.271,0.219 10 false *b 2.219,4.198 2.479,4.406 0.26,0.208 10 false *a 0.865,4.177 1.135,4.396 0.271,0.219 10 false *b
*a Lock Piece
*b Adjuster Case Cover


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the transmission control cable assembly will not be able to lock, and reliable shift operation will not be possible.



Hide 33504F 4.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 33554C 5.INSTALL SHIFT LOCK RELEASE BUTTON COVER

a.
C370835

Engage the 2 claws and guide to install the shift lock release button cover to the rear upper console panel sub-assembly.