When any of the following conditions are met, the skid control ECU (brake booster with master cylinder assembly) sets the drive output (STPO) ON which operates the stop light control relay (stop light switch assembly) and turns on the stop lights.
Pre-collision brake is operating.*
The dynamic radar cruise control system is operating and is applying the brakes.*
Secondary collision brake is operating.
Brake hold is operating.
The parking brake is engaged while the vehicle is being driven.
*: w/ Pre-collision System
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1380 | Stop Light Control Relay Malfunction | 761
762 |
·
INF Code: 761 -
When terminal IG1 voltage is 9.5 V or more, stop light drive output (STPO) is on and STP2 is off for 2 seconds or more. ·
INF Code: 762 -
When terminal IG1 voltage is 9.5 V or more, stop light drive output (STPO) is off and the input signals for STP and STP2 differ for 5 seconds or more. |
·
Wire harness or connector ·
Stop light switch assembly ·
Skid control ECU (brake booster with master cylinder assembly) ·
Rear combination light assembly LH ·
Rear combination light assembly RH ·
Center stop light set ·
Hybrid vehicle control ECU assembly ·
Certification ECU (smart key ECU assembly) ·
Vehicle approaching speaker controller* |
VSC DTC |
*: w/ Vehicle Approaching Speaker Switch
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-12 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| A40-22 (STPO) - Body ground | Always | 11 to 14 V |
| A40-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-37 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Result | Proceed to |
|---|---|
| All terminal voltages are normal. | A |
| Only STP2 terminal voltage abnormal. | B |
| Only STPO terminal voltage abnormal. | C |
| Only STP terminal voltage abnormal. | D |
| STPO terminal and STP terminal voltage abnormal. | E |
A
B
C
D
E
Reconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | Relay ON/OFF | - |
| Tester Display |
|---|
| Stop Light Relay |
According to the display on the GTS, perform the Active Test and check the operation of the stop lights.
Stop lights turn on/off in accordance with the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | Relay ON/OFF | - |
| Tester Display |
|---|
| Stop Light Relay |
According to the display on the GTS, perform the Active Test.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTC C1380 is output. | A |
| DTC C1380 is not output. | B |
A
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | Relay ON/OFF | - |
| Tester Display |
|---|
| Stop Light Relay |
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-4 (ACC) - Body ground | Active Test is on | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A28 hybrid vehicle control ECU assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-37 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the R8 certification ECU (smart key ECU assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-37 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Vehicle Approaching Speaker Switch) | B |
| NG (w/o Vehicle Approaching Speaker Switch) | C |
A
B
C
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the K160 vehicle approaching speaker controller connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-37 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-37 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A37 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-37 (STP2) - Body ground | Always | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-37 (STP2) - A37-3 (L) | Always | Below 1 Ω |
| A40-37 (STP2) or A37-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A37 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-22 (STPO) - A37-4 (ACC) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the W13 rear combination light assembly LH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-12 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the W12 rear combination light assembly RH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-12 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the R47 center stop light set connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 11 to 14 V |
| A40-12 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A37 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (STP) - Body ground | Always | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-1 (OUT) - A40-12 (STP) | Always | Below 1 Ω |
| A37-1 (OUT) or A40-12 (STP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A37 stop light switch assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-7 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-22 (STPO) or A37-4 (ACC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG