Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM (w/ Vehicle Approaching Speaker Switch) › 2019.10–2020.08
RM33C0E _59 Vehicle Exterior _074891 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0363660 VEHICLE PROXIMITY NOTIFICATION SYSTEM(w/ Vehicle Approaching Speaker Switch) U

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM(w/ Vehicle Approaching Speaker Switch)  TERMINALS OF ECU  


CHECK VEHICLE APPROACHING SPEAKER CONTROLLER


E228856E23
3.427,0.177 3.833,0.438 0.406,0.26 3.469,0.219 3.833,0.385 0.365,0.167 10 false K160

a.

Disconnect the K160 vehicle approaching speaker controller connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K160-1 (IG) - Body ground LA-B - Body ground IG power supply Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
K160-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Connect the K160 vehicle approaching speaker controller connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K160-2 (STP) - K160-7 (GND) LA-L - W-B Stop light signal input Power switch off, brake pedal depressed 8 V or higher
Power switch off, brake pedal released Below 1 V
K160-3 (SP+) - K160-8 (SP-) GR - W Vehicle approaching speaker output Vehicle approaching speaker operating A waveform synchronized with the sound is output.
(See Waveform 1)
K160-5 (SW) - K160-7 (GND) LA-R - W-B Vehicle approaching speaker switch signal input Power switch on(IG), vehicle approaching speaker switch not pressed Below 1 V
Power switch on(IG), vehicle approaching speaker switch pressed 6 V or higher
K160-6 (SPD) - K160-7 (GND) G - W-B Speed signal input Power switch on (IG), wheel being rotated Pulse generation
(See Waveform 2)
K160-9 (PRST) - K160-7 (GND) LG - W-B SIL communication signal Power switch on (IG), during transmission Pulse generation
(See Waveform 3)
K160-10 (IND) - K160-7 (GND) R - W-B Warning signal output Power switch on (IG), vehicle proximity notification off indicator light on Below 1.8 V
Power switch on (IG), vehicle proximity notification off indicator light off 11 to 14 V
K160-11 (KOK) - K160-7 (GND) BE - W-B Permission signal Power switch on (READY), shift lever in P Below 2.3 V
Power switch on (READY), engine stopped and shift lever not in P 8 V or higher

i.
E289167

Waveform 1

Item Condition
Tester Connection K160-3 (SP+) - K160-8 (SP-)
Tool Setting 1 V/DIV., 200 ms./DIV.
Vehicle Condition Vehicle approaching speaker operating


ii.
E267248N03
2.969,1.229 3.354,1.427 0.385,0.198 10 false GND 1.156,1.667 1.333,1.865 0.177,0.198 10 false A

Waveform 2

Item Condition
Tester Connection K160-6 (SPD) - K160-7 (GND)
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Power switch on (IG), wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



iii.
E288729N02
0.146,1.594 0.604,1.792 0.458,0.198 10 false GND

Waveform 3

Item Condition
Tester Connection K160-9 (PRST) - K160-7 (GND)
Tool Setting 5 V/DIV., 10 ms./DIV.
Vehicle Condition Power switch on (IG), during transmission