Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.10–2020.08
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0328967 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the hybrid vehicle control ECU assembly. When the hybrid vehicle control ECU assembly receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to the terminal STP. When the brake is applied, voltage is normally applied to the terminal STP of the hybrid vehicle control ECU assembly through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU assembly turns the dynamic radar cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure While the power switch is on (IG) and the dynamic radar cruise control system is operating, voltage of the STP terminal and that of the ST1- terminal of the hybrid vehicle control ECU assembly are less than 1 V for approximately 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

Hybrid vehicle control ECU assembly



WIRING DIAGRAM

A432094E02
0.281,0.573 1.969,0.771 1.688,0.198 10 false from J/B-B Fuse 0.385,1.073 1.344,1.531 0.958,0.458 10 false from IG2-NO. 2 Relay 2.292,0.74 3.979,0.938 1.688,0.198 10 false STOP 2.063,1.25 3.75,1.448 1.688,0.198 10 false ECU-IG2 NO.3 2.958,1.969 5.052,2.396 2.094,0.427 10 false Stop Light Switch Assembly 2.646,1.969 4.333,2.167 1.688,0.198 10 false A37 3.24,0.479 3.385,0.646 0.146,0.167 10 false 7 3.25,0.979 3.396,1.146 0.146,0.167 10 false 6 3.26,1.469 3.406,1.635 0.146,0.167 10 false 2 4.219,0.354 4.365,0.521 0.146,0.167 10 false 3 4.24,1.135 4.385,1.302 0.146,0.167 10 false 5 3.469,0.594 3.615,0.76 0.146,0.167 10 false B 3.469,1.094 3.615,1.26 0.146,0.167 10 false B 3.469,1.625 4.073,1.938 0.604,0.313 10 false GND 4,0.469 4.146,0.635 0.146,0.167 10 false L 4.01,1.25 4.156,1.417 0.146,0.167 10 false L 5.188,0.24 5.375,0.396 0.188,0.156 10 false 15 5.177,1.021 5.365,1.177 0.188,0.156 10 false 28 5.552,0.354 5.927,0.542 0.375,0.188 10 false STP 5.563,1.146 5.938,1.333 0.375,0.188 10 false ST1- 5.135,0.458 5.51,0.646 0.375,0.188 10 false A28 5.135,1.25 5.51,1.438 0.375,0.188 10 false A29 5.25,1.979 6.948,2.49 1.698,0.51 10 false Hybrid Vehicle Control ECU Assembly 2.344,3.427 4.677,3.938 2.333,0.51 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.01,3.427 3.698,3.625 1.688,0.198 10 false A40 3.781,3.031 5.469,3.229 1.688,0.198 10 false STP2 4.24,2.917 5.927,3.115 1.688,0.198 10 false 37 5.635,3.031 6.021,3.219 0.385,0.188 10 false STP1 5.365,2.906 5.75,3.094 0.385,0.188 10 false 25 5.333,3.406 6.844,3.938 1.51,0.531 10 false Certification ECU (Smart Key ECU Assembly) 5.052,3.406 5.438,3.594 0.385,0.188 10 false R8 5.167,4.896 6.99,5.375 1.823,0.479 10 false Vehicle Approaching Speaker Controller 4.76,4.896 5.26,5.083 0.5,0.188 10 false K160 5.427,4.396 5.813,4.583 0.385,0.188 10 false 2 5.625,4.5 6.01,4.688 0.385,0.188 10 false STP

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
A395526C06
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.552,0.344 2.01,0.542 0.458,0.198 10 false A37
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A37 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-7 (B) - Body ground Always 11 to 14 V
A37-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A37-6 (B) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


b.

Disconnect the A37 stop light switch assembly connector.


c.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the K160 vehicle approaching speaker controller connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-28 (ST1-) - A37-5 (L) Always Below 1 Ω
A28-15 (STP) - A37-3 (L) Always Below 1 Ω
A29-28 (ST1-) or A37-5 (L) - Body ground Always 10 kΩ or higher
A28-15 (STP) or A37-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR