Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0331447 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P05A212  Active Grille Air Shutter "A" Circuit Short to Battery  


DESCRIPTION

Refer to DTC P059A71.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P059A71

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05A212 Active Grille Air Shutter "A" Circuit Short to Battery Short to +B in swing grille actuator assembly or grille shutter motor drive circuit for 7.86 seconds or more (1 trip detection logic). Radiator shutter assembly Does not come on DTC stored SAE Code: P05A4

MONITOR DESCRIPTION

When the swing grille actuator assembly detects that there is a grille shutter circuit malfunction, a DTC request is sent to the ECM and the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Swing grille actuator assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P05A212.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

NOTICE:
·

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

- for Nickel Metal Hydride: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

- for Nickel Metal Hydride: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

- for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

Turn the ignition switch off and wait for 30 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

f.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.


Result:
Proceed to
NEXT



NEXT

2.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)
2.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Grille Shutter Initialization.

Powertrain > Engine > Utility
Tester Display
Grille Shutter Initialization
50005 372 5673

e.

According to the display on the GTS, perform initialization (nominal torque).


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (DTC P05A212)
4.CHECK DTC OUTPUT (DTC P05A212)
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P05A212 is not output A
DTC P05A212 is output B



HINT:

Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



A

5.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)

B

REPLACE RADIATOR SHUTTER ASSEMBLY

5.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Switch Grille Shutter Control Mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

e.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


f.

Enter the following menus: Powertrain / Engine / Data List / Grille Shutter Control Mode.

Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304

g.

Read the value displayed on the GTS.

Standard:
GTS Display Specified Condition
Grille Shutter Control Mode Normal


Result:
Proceed to
NEXT




NEXT

END