The skid control ECU (brake booster with master cylinder assembly) communicates with the hybrid vehicle control ECU assembly and controls braking force according to the motor's regenerative force.
The skid control ECU (brake booster with master cylinder assembly) sends VSC+/VSC and cooperative control with EPS signals to the hybrid vehicle control ECU assembly and receives operating signals from the hybrid vehicle control ECU assembly.
The skid control ECU (brake booster with master cylinder assembly) uses CAN communication for communicating with the hybrid vehicle control ECU assembly. If a communication malfunction is detected, the skid control ECU (brake booster with master cylinder assembly) prohibits VSC+/VSC and cooperative control with EPS operation, brake hold operation and part of the electronically controlled brake system control as a fail-safe function.
If the signals from the hybrid vehicle control ECU assembly return to normal, the warning light will go off and the DTCs C1259 and C1310 will be cleared.
These DTCs will be output from the skid control ECU (brake booster with master cylinder assembly) when the hybrid vehicle control ECU assembly sends a malfunction signal to the skid control ECU (brake booster with master cylinder assembly).
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1259 | HV Control System Regenerative Malfunction | 1132 | A regeneration malfunction signal is input for at least 0.036 seconds when IG2 terminal voltage is 9.5 V or more for at least 2 seconds and communication with the hybrid vehicle control ECU assembly is valid. | ·
Hybrid vehicle control ECU assembly (Regeneration malfunction) ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC
|
| C1310 | HV System Malfunction | 1140
1141 |
·
INF Code: 1140 -
When the IG2 terminal voltage is 9.5 V or more for 2 seconds or more and communication with the hybrid vehicle control ECU assembly is possible, an internal malfunction signal is detected for 0.072 seconds or more. ·
INF Code: 1141 -
The hybrid control malfunction signal is received for at least 0.072 seconds from hybrid vehicle control ECU assembly. |
·
INF Code: 1140 -
Hybrid vehicle control ECU assembly (VSC malfunction) -
Skid control ECU (brake booster with master cylinder assembly) ·
INF Code: 1141 -
Hybrid vehicle control ECU assembly (Brake hold control malfunction) -
Skid control ECU (brake booster with master cylinder assembly) |
·
INF Code: 1140 VSC DTC
·
INF Code: 1141 Brake hold DTC
|
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Check if a hybrid control system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if a motor generator control system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
for Lithium-ion Battery: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if a SFI system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output (for Lithium-ion Battery). | A |
| DTCs are not output (for Nickel Metal Hydride Battery). | B |
| DTCs are output. | C |
A
B
C
w/ Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING
w/o Canister Pump Module: Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if a hybrid battery system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1259 and/or C1310 are output. | A |
| DTCs other than C1259 and C1310 are output. | B |
| DTCs are not output. | C |
A
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING