Home › Engine / Hybrid System › A25A-FXS (EMISSION CONTROL) › EGR COOLER › from 2020.08
RM33C0E _51 Engine / Hybrid System _065422 A25A-FXS EMISSION CONTROL _0322974 EGR COOLER A

A25A-FXS EMISSION CONTROL  EGR COOLER  INSTALLATION  


PROCEDURE

Hide 25680 1.INSTALL EGR COOLER ASSEMBLY

a.
A472575

Using an 8 mm socket wrench, loosen the 4 bolts of the No. 1 EGR pipe sub-assembly.

HINT:
·

As the bolts of the No. 1 EGR pipe sub-assembly are only to be loosened, it is not necessary to replace the EGR inlet gasket and EGR valve adapter gasket.

·

If the No. 1 EGR pipe sub-assembly is removed, it is necessary to replace the EGR inlet gasket and EGR valve adapter gasket with new ones.




b.
A472571

Using an 8 mm socket wrench, loosen the 2 bolts of the EGR valve assembly.


c.
A472569C02
1.156,1.906 0.792,2.021 0.792,2.021 1.042,1.813 false 0.917,1.604 0.542,1.417 0.542,1.417 0.979,1.458 false 2.458,0.635 2.458,1.104 2.458,1.104 2.146,0.708 false 2.427,0.385 2.021,0.177 2.021,0.177 2.125,0.469 false 0.313,1.292 0.594,1.573 0.281,0.281 10 false *a 0.573,1.979 0.823,2.177 0.25,0.198 10 false *a 2.448,1.146 2.698,1.344 0.25,0.198 10 false *a 1.781,0.073 2.104,0.344 0.323,0.271 10 false *a
*a Claw


Install a new EGR cooler gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR cooler gasket are toward the EGR cooler assembly side.



d.

Install a new EGR valve gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR cooler assembly side.



e.
A472568C02
1.333,1.781 1.563,2.01 0.229,0.229 10 true 1 2.688,1.708 3.073,1.99 0.385,0.281 10 true 3 *a 2.792,1.302 3.021,1.531 0.229,0.229 10 true 2 1.771,0.542 1.979,0.729 0.208,0.188 10 true 4 0.458,0.76 0.667,0.948 0.208,0.188 10 true 5
*a Bolt or Nut


Type A:

i.

Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 3 bolts and 2 nuts.


ii.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



f.

Type B:

i.

Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 2 bolts and 3 nuts.


ii.

Tighten the 2 bolts and 3 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



g.

Connect the No. 3 water by-pass hose and No. 4 water by-pass hose to the EGR cooler assembly and slide the 2 clips to secure them.


h.

Using an 8 mm socket wrench, tighten the 2 bolts of the EGR valve assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Using an 8 mm socket wrench, tighten the 4 bolts of the No. 1 EGR pipe sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide G9200 2.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 3.ADD ENGINE COOLANT (for Engine)

Hide 4.INSPECT FOR COOLANT LEAK (for Engine)