Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  U011187  Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message  


DESCRIPTION

The hybrid vehicle control ECU assembly transmits and receives signals via CAN communication to and from the battery ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message The hybrid vehicle control ECU assembly cannot receive signals from the battery ECU assembly
(1 trip detection logic)
·

Battery ECU assembly

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A475449E04
0.667,4.156 3.604,4.542 2.938,0.385 10 false Hybrid Vehicle Control ECU Assembly 5.5,4.583 7.135,4.823 1.635,0.24 10 false Battery ECU Assembly 0.719,4.594 2.323,4.813 1.604,0.219 10 false Auxiliary Battery 0.719,5.354 2.708,5.552 1.99,0.198 10 false : CAN Communication Line 2.938,1.646 3.896,1.875 0.958,0.229 10 false IGCT 4.156,1.104 5.115,1.333 0.958,0.229 10 false IGCT NO. 2 1.323,1.094 2.281,1.323 0.958,0.229 10 false IGCT 1.531,1.396 2.49,1.625 0.958,0.229 10 false MREL 1.521,2.74 2.479,2.969 0.958,0.229 10 false CA4H 1.521,3.104 2.479,3.333 0.958,0.229 10 false CA4L 5.958,3.104 6.917,3.333 0.958,0.229 10 false CA1L 5.958,2.729 6.917,2.958 0.958,0.229 10 false CA1H 5.958,0.938 6.917,1.167 0.958,0.229 10 false IGCT 2,1.375 2.958,1.604 0.958,0.229 10 false A29 2.083,1.208 3.042,1.438 0.958,0.229 10 false 6 2.76,1.292 3.719,1.521 0.958,0.229 10 false 1 3.354,1.271 4.313,1.5 0.958,0.229 10 false 2 2.75,0.865 3.708,1.094 0.958,0.229 10 false 3 3.333,0.865 4.292,1.094 0.958,0.229 10 false 5 1.219,0.833 2.177,1.063 0.958,0.229 10 false 1 1.646,0.833 2.604,1.063 0.958,0.229 10 false 2 4.677,0.833 5.635,1.063 0.958,0.229 10 false 2 4.198,0.833 5.156,1.063 0.958,0.229 10 false 1 5.688,0.844 6.646,1.073 0.958,0.229 10 false 13 5.708,2.573 6.667,2.802 0.958,0.229 10 false 25 5.688,2.938 6.646,3.167 0.958,0.229 10 false 26 2.01,2.542 2.969,2.771 0.958,0.229 10 false 34 2.021,2.927 2.979,3.156 0.958,0.229 10 false 35 1.979,2.729 2.938,2.958 0.958,0.229 10 false K69 1.979,3.094 2.938,3.323 0.958,0.229 10 false K69 5.948,0.302 6.906,0.531 0.958,0.229 10 false AM 5.75,0.219 6.708,0.448 0.958,0.229 10 false 1 4.167,0.177 5.125,0.406 0.958,0.229 10 false 1 4.646,0.177 5.604,0.406 0.958,0.229 10 false 2 4.156,0.448 5.115,0.677 0.958,0.229 10 false ECU-B NO. 1 2.563,0.448 3.521,0.677 0.958,0.229 10 false J/B-B 2.5,0.177 3.458,0.406 0.958,0.229 10 false 1 2.917,0.188 3.875,0.417 0.958,0.229 10 false 2 5.958,4.042 6.917,4.271 0.958,0.229 10 false GND1 5.958,3.604 6.917,3.833 0.958,0.229 10 false GND 5.719,3.531 6.677,3.76 0.958,0.229 10 false 27 5.76,3.958 6.719,4.188 0.958,0.229 10 false 3 5.5,4.385 6.458,4.615 0.958,0.229 10 false z16 1.271,0.438 2.229,0.667 0.958,0.229 10 false MAIN

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

·

As interlock circuit DTCs or other DTCs may be stored when the power switch is turned on (IG) in the following procedure, make sure to clear the DTCs after inspection.



PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


d.

Check and record any hybrid control system DTCs and freeze frame data. Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
DTCs related to Hybrid Battery System are not output. A
DTCs related to Hybrid Battery System are output. B



e.

Turn the power switch off.



A

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)

B

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the z16 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.
A407388C29
1.49,0.396 1.938,0.635 0.448,0.24 1.167,2.156 0.406,1.656 true 2.229,3.115 1.365,2.406 true 1.167,2.26 0.802,3.125 true 0.146,0.115 0.604,0.531 0.458,0.417 10 false *a 1.594,0.427 2.052,0.844 0.458,0.417 10 false z16 0.188,1.563 0.646,1.979 0.458,0.417 10 false AM 2.313,3.083 2.927,3.292 0.615,0.208 10 false GND 0.646,3.146 1.115,3.365 0.469,0.219 10 false IGCT
*a Front view of wire harness connector
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z16-1 (AM) - z16-27 (GND) Power switch off 11 to 14 V
z16-13 (IGCT) - z16-27 (GND) Power switch on (IG) 11 to 14 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction in the battery ECU assembly power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Reconnect the z16 battery ECU assembly connector.


i.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BATTERY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the K69 hybrid vehicle control ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU assembly and battery ECU assembly is not loose or disconnected.





d.
A406229E02
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A407398C03
1.5,0.094 1.896,0.375 0.396,0.281 1.854,2.375 2.25,2.656 0.396,0.281 0.438,1.563 1.25,1.74 true 0.344,0.906 1.365,1.75 true 1.167,4.26 1.833,4.052 true 2.604,4.292 1.896,4.052 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.083,2.083 0.396,2.281 0.313,0.198 10 false *b 1.583,0.156 1.896,0.354 0.313,0.198 10 false z16 1.958,2.438 2.271,2.635 0.313,0.198 10 false K69 0.073,1.469 0.552,1.667 0.479,0.198 10 false CA1H 0.865,4.313 1.344,4.51 0.479,0.198 10 false CA4L 0.052,0.771 0.531,0.969 0.479,0.198 10 false CA1L 2.625,4.323 3.104,4.521 0.479,0.198 10 false CA4H
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-25 (CA1H) - K69-34 (CA4H) Power switch off Below 1 Ω
z16-26 (CA1L) - K69-35 (CA4L) Power switch off Below 1 Ω
K69-34 (CA4H) - Other terminals and body ground Power switch off 10 kΩ or higher
K69-35 (CA4L) - Other terminals and body ground Power switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery ECU assembly and hybrid vehicle control ECU assembly is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z16-25 (CA1H) - Body ground Power switch on (IG) Below 1 V
z16-26 (CA1L) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the z16 battery ECU assembly connector.


l.

Install the No. 1 HV battery hose.


m.

Reconnect the K69 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229E02
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A407388C30
1.49,0.354 1.938,0.594 0.448,0.24 1.167,2.396 0.542,3.021 true 1.375,3.031 1.292,2.406 true 2.115,3.073 1.375,2.396 true 0.146,0.115 0.604,0.531 0.458,0.417 10 false *a 1.646,0.406 2.115,0.667 0.469,0.26 10 false z16 0.281,3.094 0.969,3.313 0.688,0.219 10 false CA1H 1.229,3.094 1.844,3.302 0.615,0.208 10 false CA1L 2.01,3.115 2.625,3.323 0.615,0.208 10 false GND
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z16-25 (CA1H) - z16-27 (GND) Power switch on (IG) 2.5 to 3.5 V
z16-26 (CA1L) - z16-27 (GND) Power switch on (IG) 1.5 to 2.5 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-25 (CA1H) - z16-26 (CA1L) Power switch off 108 to 132 Ω



j.

Reconnect the z16 battery ECU assembly connector.


k.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY