Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY ECU (for LITHIUM-ION BATTERY) › 2020.08–2021.02
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442442 BATTERY ECU(for LITHIUM-ION BATTERY) A

HYBRID / BATTERY CONTROL  BATTERY ECU(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of battery ECU assembly Current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The type of battery ECU assembly to be used varies depending on the vehicle model.

·
A391075C02
1.135,1.198 1.448,0.292 1.448,0.292 1.708,0.292 true 1.771,0.229 2.083,0.427 0.313,0.198 10 false *a
*a Black Label


The type of battery ECU assembly can be confirmed by the color of the label.

·

If the wrong type of battery ECU assembly is installed, the power switch cannot be turned on (READY).

·

After installing the battery ECU assembly, perform the following to check that the power switch can be turned on (READY).

-

Turn the power switch on (READY).

-

Turn the power switch off and wait for 30 seconds or more.

-

Turn the power switch on (READY) again.




PROCEDURE

Hide 1. WHEN REPLACING BATTERY ECU ASSEMBLY

HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

NOTICE:
·

Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the battery ECU assembly or ECM with a used one from another vehicle.



a.

Procedure when replacing both battery ECU assembly and ECM:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either ECU.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the power switch on (READY) and wait for 5 minutes or more.


v.

Turn the power switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the power switch can be turned on (READY).

HINT:

If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 82111 3.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 82111 7.CONNECT ENGINE ROOM MAIN WIRE

Hide 899A0A 8.REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 67918A 9.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 10.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 11.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 12.REMOVE REAR UNDER SIDE COVER RH

Hide 71033 14.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G920NB 20.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A391071C02
1.604,0.073 1.917,0.271 0.313,0.198 10 false *a 2.813,0.375 3.125,0.573 0.313,0.198 10 false *a 3.24,0.417 3.427,0.594 0.188,0.177 10 false *a 3.083,1.969 3.354,2.135 0.271,0.167 10 false *a 0.063,1.063 0.26,1.24 0.198,0.177 10 true *a 2.052,0.104 2.365,0.302 0.313,0.198 10 false *b 2.635,1.938 2.865,2.104 0.229,0.167 10 false *b 2.135,1.99 2.354,2.167 0.219,0.177 10 false *b 1.677,1.865 1.99,2.063 0.313,0.198 10 false *b 1.344,1.792 1.656,1.99 0.313,0.198 10 false *b 0.854,1.594 1.167,1.792 0.313,0.198 10 false *b 0.365,1.448 0.677,1.646 0.313,0.198 10 false *b
*a Bolt
*b Nut


Remove the 5 bolts, 7 nuts and upper HV battery cover sub-assembly from the HV battery.


Hide G929A 21.REMOVE NO. 1 HV BATTERY HOSE

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A391072

Remove the 2 clips.


b.

Disengage the 2 claws to remove the No. 1 HV battery hose from the HV battery.


Hide 89890A 22.REMOVE BATTERY ECU ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A391073

Disengage the clamp.


b.

Move the lock lever while pushing the lock, and disconnect the 3 battery ECU assembly connectors.

NOTICE:
·
A393180C01
1.51,2.76 1.708,2.76 1.708,2.76 2.021,2.385 true 1.333,2.688 1.646,2.885 0.313,0.198 10 false *a
*a Lever Lock


Make sure to release the lock of the lock lever before moving it.

·

If the connector cannot be disconnected, check if the lock lever is completely unlocked.

·

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.




c.
A391074

Remove the 3 nuts and battery ECU assembly from the HV battery.

NOTICE:

If the battery ECU assembly has been struck or dropped, replace it.