Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P310711  Lost Communication with Airbag System Control Module Circuit Short to Ground  


DESCRIPTION

The hybrid vehicle control ECU assembly detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P310711 Lost Communication with Airbag System Control Module Circuit Short to Ground Short to ground in the communication circuit:
Communication from the airbag sensor assembly stopped and Circuit Low has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Hybrid vehicle control ECU assembly


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P310711 Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A412316E01
1,2.115 1.458,2.313 0.458,0.198 10 false K73 0.979,2.292 2.604,2.531 1.625,0.24 10 false Airbag Sensor Assembly 2.094,1.292 2.552,1.49 0.458,0.198 10 false E1 2.406,1.302 2.865,1.5 0.458,0.198 10 false 33 2.396,1.01 2.854,1.208 0.458,0.198 10 false 24 4.583,0.906 5.042,1.104 0.458,0.198 10 false 14 1.896,1.01 2.354,1.208 0.458,0.198 10 false GSW2 4.896,1.01 5.354,1.208 0.458,0.198 10 false ABFS 4.531,1.104 4.99,1.302 0.458,0.198 10 false K70 6.094,1.531 6.552,1.729 0.458,0.198 10 false K69 5.813,1.542 6.271,1.74 0.458,0.198 10 false E1 4.354,2.125 7.156,2.396 2.802,0.271 10 false Hybrid Vehicle Control ECU Assembly 5.594,0.531 6.052,0.729 0.458,0.198 10 false +B 6.177,1.344 6.635,1.542 0.458,0.198 10 false 6

PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK AIR BAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIR BAG SENSOR ASSEMBLY (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU assembly terminals specified in the table below.


b.

Turn the power switch on (READY).


c.
A407411C01
2.448,0.354 2.844,0.594 0.396,0.24 1.854,0.354 2.25,0.594 0.396,0.24 2.146,1.813 2.573,1.219 true 1.469,1.802 1.833,1.146 true 3.01,3.333 3.354,3.542 0.344,0.208 10 false GND 2.51,0.396 2.969,0.594 0.458,0.198 10 false K70 1.917,1.854 2.375,2.052 0.458,0.198 10 false ABFS 1.906,0.375 2.365,0.573 0.458,0.198 10 false K69 1.365,1.844 1.823,2.042 0.458,0.198 10 false E1 0.094,0.083 0.552,0.281 0.458,0.198 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Measure the waveform.

Item Contents
Terminal K70-14 (ABFS) - K69-6 (E1)
Equipment Setting 5 V/DIV., 150 ms./DIV.
Condition Power switch on (READY)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



d.

Turn the power switch off.



A

3.CLEAR DTC

B

6.CHECK AIR BAG SENSOR ASSEMBLY
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P310711 is not output. A
P310711 is output. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

5.CHECK FOR INTERMITTENT PROBLEMS

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK AIR BAG SENSOR ASSEMBLY
a.

Disconnect the K73 airbag sensor assembly connector.


b.
C371896C05
1.333,0.135 1.771,0.375 0.438,0.24 0.99,0.344 1.458,1.073 true 1.063,1.792 1.458,1.219 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.417,0.177 1.771,0.333 0.354,0.156 10 false K73 0.531,0.115 0.99,0.271 0.458,0.156 10 false GSW2 0.885,1.75 1.198,1.906 0.313,0.156 10 false E1
*a Component without harness connected
(Airbag sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K73-24 (GSW2) - K73-33 (E1) Power switch off 10 kΩ or higher



c.

Reconnect the K73 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - AIRBAG SENSOR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K73 airbag sensor assembly connector.


c.
A407410C01
2.448,0.083 2.865,0.333 0.417,0.25 1.479,2.427 1.896,2.677 0.417,0.25 2.063,2.01 2.594,1.75 true 1.854,3.646 2.594,3.792 true 2.51,0.125 3.01,0.354 0.5,0.229 10 false K70 1.646,2.021 2.146,2.25 0.5,0.229 10 false ABFS 0.094,0.073 0.594,0.302 0.5,0.229 10 false *a 1.542,2.479 2.042,2.708 0.5,0.229 10 false K73 2.646,3.729 3.146,3.958 0.5,0.229 10 false GSW2 0.115,2.448 0.615,2.677 0.5,0.229 10 false *b
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K70-14 (ABFS) or K73-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the K73 airbag sensor assembly connector.


e.

Reconnect the K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR