Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV drive mode signal will be sent to the hybrid vehicle control ECU assembly when the EV drive mode switch (electric parking brake switch assembly) is operated. If the specified conditions are met, the system enters EV drive mode and the vehicle will be driven using EV drive mode. This signal is then transmitted from the hybrid vehicle control ECU assembly via CAN to the combination meter assembly to illuminate the EV drive mode indicator.

WIRING DIAGRAM

A376617E12
1.49,1.25 3.438,1.563 1.948,0.313 10 false Combination Meter Assembly 2.125,1.896 2.875,2.156 0.75,0.26 10 false EV MODE 1.406,2.823 3.438,3.458 2.031,0.635 10 false EV Drive Mode Switch (Electric Parking Brake Switch Assembly) 4.531,2.958 6.938,3.448 2.406,0.49 10 false Hybrid Vehicle Control ECU Assembly 5.104,2.063 5.688,2.323 0.583,0.26 10 false EVSW 4.802,2.063 5.083,2.344 0.281,0.281 10 false 15 4.521,2.771 4.802,3.052 0.281,0.281 10 false K70 1.406,2.635 1.688,2.917 0.281,0.281 10 false K37 5.76,1.635 6.042,1.917 0.281,0.281 10 false +B 1.375,1.885 1.802,2.104 0.427,0.219 10 false 16*1 1.75,2.063 2.219,2.375 0.469,0.313 10 false GND1 3,2.073 3.281,2.354 0.281,0.281 10 false S 3.208,1.885 3.583,2.083 0.375,0.198 10 false 14*1 0.583,3.396 2.531,3.708 1.948,0.313 10 false : CAN Communication Line 3.208,2.063 3.583,2.26 0.375,0.198 10 false 11*2 1.438,2.063 1.865,2.281 0.427,0.219 10 false 9*2 0.167,0.188 0.948,0.396 0.781,0.208 10 false *1: for LHD 0.167,0.51 0.948,0.719 0.781,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV mode and a warning message will be displayed on the multi-information display.

HINT:

Under the following conditions, the drive mode will not be able to be changed to EV mode:

·

The hybrid control system is extremely hot.

·

The hybrid control system is extremely cold.

·

The engine is warming up.

·

The SOC (State of Charge) of the HV battery is low.

·

The vehicle is being driven at a speed higher than the specified value.

-

The vehicle speed is approximately 55 km/h (34 mph) or higher.


·

The accelerator pedal is being fully depressed or the vehicle is climbing a slope.

·

The defroster is on.

·

DTCs are stored.



PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.

Result:
Result Proceed to
No buzzer sounded and no message was displayed on multi-information display A
A buzzer sounded and a message was displayed on multi-information display B


HINT:

If a buzzer sounds or a message is displayed on the multi-information display, one or more of the EV drive mode entry conditions have not been met. Check that all of the EV drive mode entry conditions have been met before pressing the EV drive mode switch.




A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

END

2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / CAN Bus Check.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



e.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



f.

Turn the power switch off.



A

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)

B

GO TO DTC CHART

4.READ VALUE USING GTS (EV MODE, EV MODE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / EV Mode, EV Mode Switch.

Powertrain > Hybrid Control > Data List
Tester Display
EV Mode
EV Mode Switch
50003 397 79,80

e.

Read the value displayed on the GTS.

Result:
Result Proceed to
The display changes according to the EV drive mode switch operation A
The display does not change according to the EV drive mode switch operation B



f.

Turn the power switch off.



A

B

5.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
5.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the K37 EV drive mode switch (electric parking brake switch assembly) connector.


b.
A406713C06
0.292,0.917 0.719,1.208 0.427,0.292 2.771,1.625 2.396,1.292 true 0.844,1.656 1.156,1.302 true 0.385,0.99 0.844,1.188 0.458,0.198 10 false K37 2.646,1.677 3.208,1.99 0.563,0.313 10 false GND1*A 0.25,0.24 0.563,0.396 0.313,0.156 10 false *a 0.469,1.688 1.083,1.938 0.615,0.25 10 false GND1*B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K37-16 (GND1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
K37-9 (GND1) - Body ground Always Below 1 Ω



c.

Reconnect the K37 EV drive mode switch (electric parking brake switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K37 EV drive mode switch (electric parking brake switch assembly) connector.


c.
A406714C03
2.427,0.281 2.833,0.542 0.406,0.26 0.406,3.271 0.813,3.531 0.406,0.26 2.438,4.156 1.938,3.615 true 2.167,2.365 2.552,2.021 true 1.073,4.135 1.479,3.604 true 2.51,0.333 2.969,0.531 0.458,0.198 10 false K70 0.49,3.333 0.948,3.531 0.458,0.198 10 false K37 0.24,0.292 0.552,0.448 0.313,0.156 10 false *a 0.271,2.677 0.583,2.833 0.313,0.156 10 false *b 2.458,4.177 2.844,4.417 0.385,0.24 10 false S*A 1.896,2.396 2.406,2.677 0.51,0.281 10 false EVSW 0.979,4.177 1.354,4.385 0.375,0.208 10 false S*B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K70-15 (EVSW) - K37-14 (S) Always Below 1 Ω
K70-15 (EVSW) or K37-14 (S) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
K70-15 (EVSW) - K37-11 (S) Always Below 1 Ω
K70-15 (EVSW) or K37-11 (S) - Body ground Always 10 kΩ or higher



d.

Reconnect the K37 EV drive mode switch (electric parking brake switch assembly) connector.


e.

Reconnect the K70 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR