Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442936 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0A1D94  Hybrid/EV Powertrain Control Module Unexpected Operation  


DESCRIPTION

The battery ECU assembly monitors the hybrid vehicle control ECU assembly via CAN communication. If the battery ECU assembly detects that the hybrid vehicle control ECU assembly is malfunctioning, it will illuminate the MIL and store a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A1D94 Hybrid/EV Powertrain Control Module Unexpected Operation Hybrid vehicle control ECU assembly internal malfunction:
An abnormal signal from the hybrid vehicle control ECU assembly is detected by the battery ECU assembly.
(1 trip detection logic)
Hybrid vehicle control ECU assembly Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)
a.
A414384C02
2.542,0.813 2.917,1.031 0.375,0.219 2.563,1.125 2.917,1.333 0.354,0.208 2.542,0.49 2.917,0.708 0.375,0.219 2.552,1.49 2.917,1.698 0.365,0.208 2.104,2.823 2.448,3.01 0.344,0.188 2.104,3.115 2.448,3.313 0.344,0.198 2.115,3.427 2.448,3.625 0.333,0.198 2.115,3.719 2.448,3.906 0.333,0.188 0.198,0.104 0.583,0.323 0.385,0.219 12 false *A 0.188,2.458 0.573,2.677 0.385,0.219 12 false *B 2.573,0.51 2.885,0.688 0.313,0.177 10 true K70 2.583,0.823 2.896,1.01 0.313,0.188 10 true K69 2.583,1.135 2.896,1.302 0.313,0.167 10 true A29 2.573,1.5 2.906,1.677 0.333,0.177 10 true A28 2.135,2.833 2.438,3 0.302,0.167 10 true K70 2.115,3.125 2.438,3.292 0.323,0.167 10 true K69 2.125,3.438 2.427,3.604 0.302,0.167 10 true A29 2.135,3.729 2.427,3.896 0.292,0.167 10 true A28
*A for LHD
*B for RHD


Check the connections of the hybrid vehicle control ECU assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Result
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Check the connector connections and contact pressure of the relevant terminals for the battery ECU assembly.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.



d.

Install the No. 1 HV battery hose.


Result:
Result
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 HYBRID BATTERY PACK WIRE))

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 HYBRID BATTERY PACK WIRE))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A408971N02
2.01,0.615 2.438,0.906 0.427,0.292 2.052,0.635 2.406,0.844 0.354,0.208 10 true R20

Check the connector connections and contact pressure of the relevant terminals for the HV battery.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.



d.

Install the No. 4 HV battery protector.


Result:
Result
OK
NG



OK

4.REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

CONNECT SECURELY

4.REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NEXT

END