Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442936 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0A9B2A  Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range  P0AC52A  Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range  P0ACA2A  Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range  P0AE82A  Hybrid/EV Battery Temperature Sensor "D" Signal Stuck In Range  P0BC22A  Hybrid/EV Battery Temperature Sensor "E" Signal Stuck In Range  P0C332A  Hybrid/EV Battery Temperature Sensor "F" Signal Stuck In Range  P306562  Hybrid/EV Battery Temperature Sensor "Group 1" Signal Compare Failure  P306A62  Hybrid/EV Battery Temperature Sensor "Group 2" Signal Compare Failure  


DESCRIPTION

Refer to the description for DTC P0A9B11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>P0A9B11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9B2A Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range The performance of battery temperature sensor 0 is abnormal and its output is stuck.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P0AC52A Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range The performance of battery temperature sensor 1 is abnormal and its output is stuck.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P0ACA2A Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range The performance of battery temperature sensor 2 is abnormal and its output is stuck.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P0AE82A Hybrid/EV Battery Temperature Sensor "D" Signal Stuck In Range The performance of battery temperature sensor 3 is abnormal and its output is stuck.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P0BC22A Hybrid/EV Battery Temperature Sensor "E" Signal Stuck In Range The performance of battery temperature sensor 4 is abnormal and its output is stuck.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P0C332A Hybrid/EV Battery Temperature Sensor "F" Signal Stuck In Range The performance of battery temperature sensor 5 is abnormal and its output is stuck.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P306562 Hybrid/EV Battery Temperature Sensor "Group 1" Signal Compare Failure The performance of any battery temperature sensor (0 to 2) is abnormal and the difference in output between it and each other battery temperature sensor is excessively large.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P306A62 Hybrid/EV Battery Temperature Sensor "Group 2" Signal Compare Failure The performance of any battery temperature sensor (3 to 5) is abnormal and the difference in output between it and each other battery temperature sensor is excessively large.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A9B2A Hybrid/EV Battery Temperature 1 to 6
P0AC52A
P0ACA2A
P0AE82A
P0BC22A
P0C332A
P306562
P306A62

HINT:

If the vehicle as is left as is for 24 hours, the value of "Hybrid/EV Battery Temperature" will be almost the same as the ambient temperature.


The following items can be helpful when performing repairs:

Data List
·

Vehicle Speed

·

Ambient Temperature


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


P0A9B2A, P0AC52A, P0ACA2A, P0AE82A, P0BC22A, P0C332A:

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid/EV Battery Temperature 1 to 6" and "Hybrid/EV Battery Current" when ambient temperature is -10°C (14°F) or higher.

HINT:
·

Check that the output of each battery temperature sensor varies.

·

Check that the difference in output between each battery temperature sensor is not excessively large.



7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




P306562, P306A62:

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 10 seconds or more when the ambient temperature is -10°C (14°F) or higher.

HINT:

Check that the difference in output between each battery temperature sensor is not large.


7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P0A9B2A, P0AC52A, P0ACA2A, P0AE82A, P0BC22A, P0C332A, P306562 or P306A62" only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


e.

Turn the power switch off.



A

2.CHECK DTC

B

C

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P0A9B2A, P0AC52A, P0ACA2A or P306562" is also output. A
"P0AE82A, P0BC22A, P0C332A, , or P306A62" is also output. B



A

3.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 0 to 2)

B

4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)
4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR 3 to 5)

OK

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

OK

NG