Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442936 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P1A8000  Hybrid/EV Battery Stack 1 Delta SOC High  P1A8500  Hybrid/EV Battery Stack 2 Delta SOC High  


DESCRIPTION

The HV battery is composed of 70 cells (3.7 V each) in series. The battery ECU assembly monitors the difference in capacity of each HV battery cell to detect malfunctions of the HV battery.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1A8000 Hybrid/EV Battery Stack 1 Delta SOC High The difference in capacity of each cell of the No. 1 HV supply stack sub-assembly exceeds the specified value.
(2 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Hybrid battery terminal block

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P1A8500 Hybrid/EV Battery Stack 2 Delta SOC High The difference in capacity of each cell of the No. 2 HV supply stack sub-assembly exceeds the specified value.
(2 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

Hybrid battery terminal block

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P1A8000
·

Hybrid/EV Battery Cell 1 to 70 Voltage

·

Hybrid/EV Battery Cell 1 to 70 Internal Resistance

·

Hybrid/EV Battery SOC

·

Hybrid/EV Battery Current

·

Hybrid/EV Battery Voltage


P1A8500

HINT:
·

These DTCs can be stored after clearing the DTCs and driving the vehicle for approximately 12 minutes.

·

In order to ensure HV battery performance, appropriate cooling performance must be maintained. Perform the following items as necessary. If cooling performance has decreased and "Maintenance Required for Traction Battery Cooling Parts See Owner's Manual" is displayed on the multi-information display, make sure to perform the following items:

-

Make sure the air intake port for HV battery is not blocked.


-

Make sure there are no gaps between the connecting parts of the ducts.


-

Clean the No. 1 HV battery intake filter.

Clear the DTCs to reset the learning values even if no DTCs are stored.





CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle on urban roads for approximately 12 minutes.

(As 2 trip detection logic is used, check for DTCs including pending DTCs.)

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P1A8000 or P1A8500" only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1AC413 Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open
P1AC49E Hybrid/EV Battery Stack 1 Current Interrupt Device Stuck On
P1AC513 Hybrid/EV Battery Stack 2 Current Interrupt Device Circuit Open
P1AC59E Hybrid/EV Battery Stack 2 Current Interrupt Device Stuck On
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P1CC81E Hybrid/EV Battery Stack 1 Voltage Difference Out of Range
P1CC91E Hybrid/EV Battery Stack 2 Voltage Difference Out of Range
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P1C2D62 Hybrid/EV Battery "A" Voltage Sensor/ Boosting Converter Voltage Sensor "A" Signal Compare Failure


e.

Turn the power switch off.



A

2.CHECK DTC

B

C

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P1A8000" is also output. A
"P1A8500" is also output. B



A

3.CHECK FREEZE FRAME DATA (HV BATTERY)

B

7.CHECK FREEZE FRAME DATA (HV BATTERY)
3.CHECK FREEZE FRAME DATA (HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV battery / Trouble Codes.


d.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 35 Voltage" for DTC P1A8000 and make a note if the value of any is the lowest voltage value.

Powertrain > HV Battery > Trouble Codes
50001 398

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK BATTERY ECU ASSEMBLY (GA0 - VA35)
4.CHECK BATTERY ECU ASSEMBLY (GA0 - VA35)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured the lowest voltage value in the previous step.


A407538C07
0.448,1.802 0.875,2.052 0.427,0.25 4.667,1.948 5.563,2.094 true 4.479,1.885 5.719,1.625 true 4.083,2.021 4.677,3.552 true 4.656,1.729 5.688,1.281 true 3.906,1.875 4.76,0.323 true 3.729,1.99 3.833,3.281 true 4.646,2.219 5.354,2.604 true 4.448,1.656 5.156,0.875 true 4.417,2.219 5.354,3.177 true 4.281,1.646 5.219,0.5 true 4.292,1.906 5.531,0.948 true 4.25,2.208 5,3.25 true 4.094,1.667 4.802,0.729 true 4.052,2.219 4.323,3.271 true 3.896,1.625 4.281,0.448 true 3.885,2.219 4.104,3.583 true 3.729,1.625 4.094,0.26 true 3.656,2.24 3.5,3.531 true 3.542,1.656 3.688,0.25 true 3.448,1.844 3.385,0.49 true 3.49,2.25 3.292,3.281 true 3.281,1.625 3.083,0.25 true 3.281,2.01 2.76,3.26 true 3.313,2.229 2.917,3.521 true 3.135,1.625 2.76,0.344 true 3.104,1.865 2.406,0.396 true 3.115,2.219 2.229,3.51 true 2.927,1.635 2.042,0.563 true 2.906,2.01 1.635,2.823 true 2.896,2.229 1.813,3.406 true 2.76,1.635 1.896,0.865 true 2.719,1.865 1.625,1.521 true 2.708,2.198 1.823,3.083 true 2.531,1.615 1.698,1.177 true 1.594,1.865 2.51,1.927 true 2.51,2.156 1.573,2.406 true 0.094,0.052 0.719,0.542 0.625,0.49 10 false *a 0.542,1.844 0.979,2.177 0.438,0.333 10 false z15 5.74,1.188 6.177,1.521 0.438,0.333 10 false GA0 5.615,2.021 6.052,2.354 0.438,0.333 10 false VA1 4.938,3.302 5.375,3.635 0.438,0.333 10 false VA8 5.406,2.604 5.844,2.938 0.438,0.333 10 false VA2 5.219,0.771 5.656,1.104 0.438,0.333 10 false VA3 5.573,0.844 6.01,1.177 0.438,0.333 10 false VA7 5.76,1.542 6.198,1.875 0.438,0.333 10 false VA4 5.385,3.177 5.823,3.51 0.438,0.333 10 false VA5 5.25,0.365 5.688,0.698 0.438,0.333 10 false VA6 4.75,0.563 5.188,0.896 0.438,0.333 10 false VA9 4.552,3.583 5.01,3.771 0.458,0.188 10 false VA10 4.198,3.302 4.646,3.542 0.448,0.24 10 false VA11 4.208,0.292 4.646,0.625 0.438,0.333 10 false VA12 4.771,0.167 5.208,0.5 0.438,0.333 10 false VA13 3.969,3.594 4.469,3.781 0.5,0.188 10 false VA14 3.979,0.094 4.448,0.365 0.469,0.271 10 false VA15 3.698,3.313 4.167,3.583 0.469,0.271 10 false VA16 3.344,3.552 3.813,3.76 0.469,0.208 10 false VA17 3.521,0.094 3.99,0.365 0.469,0.271 10 false VA18 3.198,0.323 3.667,0.594 0.469,0.271 10 false VA19 3.115,3.302 3.583,3.51 0.469,0.208 10 false VA20 2.896,0.094 3.365,0.365 0.469,0.271 10 false VA21 2.552,3.271 3.063,3.49 0.51,0.219 10 false VA22 2.74,3.563 3.208,3.771 0.469,0.208 10 false VA23 2.521,0.177 2.99,0.448 0.469,0.271 10 false VA24 2.083,0.26 2.552,0.531 0.469,0.271 10 false VA25 2.021,3.542 2.5,3.771 0.479,0.229 10 false VA26 1.708,0.458 2.177,0.729 0.469,0.271 10 false VA27 1.26,2.76 1.729,3.031 0.469,0.271 10 false VA28 1.573,3.438 2.042,3.708 0.469,0.271 10 false VA29 1.552,0.75 2.021,1.021 0.469,0.271 10 false VA30 1.281,1.448 1.75,1.719 0.469,0.271 10 false VA31 1.469,3.094 1.938,3.365 0.469,0.271 10 false VA32 1.354,1.083 1.823,1.354 0.469,0.271 10 false VA33 1.229,1.792 1.698,2.063 0.469,0.271 10 false VA34 1.208,2.344 1.677,2.615 0.469,0.271 10 false VA35
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
HV Battery Cell Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
1 z15-1 (GA0) (-) - z15-13 (VA1) (+) Always 50 kΩ or more
2 z15-13 (VA1) (-) - z15-25 (VA2) (+) Always 50 kΩ or more
3 z15-25 (VA2) (-) - z15-2 (VA3) (+) Always 50 kΩ or more
4 z15-2 (VA3) (-) - z15-14 (VA4) (+) Always 50 kΩ or more
5 z15-14 (VA4) (-) - z15-26 (VA5) (+) Always 50 kΩ or more
6 z15-26 (VA5) (-) - z15-3 (VA6) (+) Always 50 kΩ or more
7 z15-3 (VA6) (-) - z15-15 (VA7) (+) Always 50 kΩ or more
8 z15-15 (VA7) (-) - z15-27 (VA8) (+) Always 50 kΩ or more
9 z15-27 (VA8) (-) - z15-4 (VA9) (+) Always 50 kΩ or more
10 z15-4 (VA9) (-) - z15-16 (VA10) (+) Always 50 kΩ or more
11 z15-16 (VA10) (-) - z15-28 (VA11) (+) Always 50 kΩ or more
12 z15-28 (VA11) (-) - z15-5 (VA12) (+) Always 50 kΩ or more
13 z15-5 (VA12) (-) - z15-17 (VA13) (+) Always 50 kΩ or more
14 z15-17 (VA13) (-) - z15-29 (VA14) (+) Always 50 kΩ or more
15 z15-29 (VA14) (-) - z15-6 (VA15) (+) Always 50 kΩ or more
16 z15-6 (VA15) (-) - z15-18 (VA16) (+) Always 50 kΩ or more
17 z15-18 (VA16) (-) - z15-30 (VA17) (+) Always 50 kΩ or more
18 z15-30 (VA17) (-) - z15-7 (VA18) (+) Always 50 kΩ or more
19 z15-7 (VA18) (-) - z15-19 (VA19) (+) Always 50 kΩ or more
20 z15-19 (VA19) (-) - z15-31 (VA20) (+) Always 50 kΩ or more
21 z15-31 (VA20) (-) - z15-8 (VA21) (+) Always 50 kΩ or more
22 z15-8 (VA21) (-) - z15-20 (VA22) (+) Always 50 kΩ or more
23 z15-20 (VA22) (-) - z15-32 (VA23) (+) Always 50 kΩ or more
24 z15-32 (VA23) (-) - z15-9 (VA24) (+) Always 50 kΩ or more
25 z15-9 (VA24) (-) - z15-21 (VA25) (+) Always 50 kΩ or more
26 z15-21 (VA25) (-) - z15-33 (VA26) (+) Always 50 kΩ or more
27 z15-33 (VA26) (-) - z15-10 (VA27) (+) Always 50 kΩ or more
28 z15-10 (VA27) (-) - z15-22 (VA28) (+) Always 50 kΩ or more
29 z15-22 (VA28) (-) - z15-34 (VA29) (+) Always 50 kΩ or more
30 z15-34 (VA29) (-) - z15-11 (VA30) (+) Always 50 kΩ or more
31 z15-11 (VA30) (-) - z15-23 (VA31) (+) Always 50 kΩ or more
32 z15-23 (VA31) (-) - z15-35 (VA32) (+) Always 50 kΩ or more
33 z15-35 (VA32) (-) - z15-12 (VA33) (+) Always 50 kΩ or more
34 z15-12 (VA33) (-) - z15-24 (VA34) (+) Always 50 kΩ or more
35 z15-24 (VA34) (-) - z15-36 (VA35) (+) Always 50 kΩ or more


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery ECU assembly.




c.

Install the battery ECU assembly.


Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



A

5.CHECK TOTAL DISTANCE DRIVEN

B

5.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1
Other than above B


HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.



A

B

6.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
6.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

7.CHECK FREEZE FRAME DATA (HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV battery / Trouble Codes.


d.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 36 Voltage" through "Hybrid/EV Battery Cell 70 Voltage" for DTC P1A8500 and make a note if the value of any is the lowest voltage value.

Powertrain > HV Battery > Trouble Codes
50001 398

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK BATTERY ECU ASSEMBLY (VAD - VA70)
8.CHECK BATTERY ECU ASSEMBLY (VAD - VA70)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured the lowest voltage value in the previous step.


A407536C07
0.333,1.927 0.698,2.177 0.365,0.25 4.604,1.885 5.917,1.552 true 4.625,2.104 5.719,2.198 true 4.625,2.333 5.615,2.583 true 4.427,1.865 5.802,1.25 true 4.427,2.052 5.896,1.854 true 4.365,2.385 5.073,3.281 true 4.24,1.844 5.469,0.781 true 4.25,2.177 5.417,2.969 true 4.198,2.406 4.708,3.521 true 4.083,1.833 5.271,0.5 true 4.073,2.042 5.271,1.188 true 4.01,2.385 4.188,3.365 true 3.875,1.813 4.688,0.344 true 3.854,2.031 4.698,0.823 true 3.833,2.406 3.844,3.531 true 3.646,1.802 3.99,0.25 true 3.677,2.042 4.26,0.521 true 3.656,2.406 3.583,3.365 true 3.479,1.833 3.542,0.24 true 3.427,2.031 3.229,0.521 true 3.469,2.385 3.188,3.552 true 3.281,1.792 2.927,0.229 true 3.26,2.042 2.729,0.583 true 3.281,2.406 2.896,3.354 true 3.083,1.792 2.375,0.333 true 3.094,2.021 2.365,0.792 true 3.094,2.396 2.469,3.563 true 2.865,1.823 1.969,0.625 true 2.875,2.156 1.656,3.021 true 2.896,2.396 2.198,3.354 true 2.719,1.802 1.865,0.958 true 2.708,2.031 1.729,1.604 true 2.688,2.396 1.74,3.406 true 2.521,1.813 1.802,1.271 true 1.552,2.094 2.51,2.094 true 2.5,2.323 1.604,2.552 true 0.344,0.115 0.875,0.76 0.531,0.646 10 false *a 0.438,1.969 0.854,2.302 0.417,0.333 10 false z13 5.656,2.542 6.156,2.792 0.5,0.25 10 false VA37 5.958,1.448 6.49,2.094 0.531,0.646 10 false VAD 5.76,2.135 6.24,2.365 0.479,0.229 10 false VA36 5.844,1.146 6.375,1.792 0.531,0.646 10 false VA38 5.938,1.76 6.458,2.01 0.521,0.25 10 false VA39 4.948,3.313 5.438,3.552 0.49,0.24 10 false VA40 5.5,0.677 6.031,1.323 0.531,0.646 10 false VA41 5.448,3 5.854,3.198 0.406,0.198 10 false VA42 4.615,3.542 5.083,3.719 0.469,0.177 10 false VA43 5.281,0.375 5.813,1.021 0.531,0.646 10 false VA44 5.323,1.104 5.854,1.75 0.531,0.646 10 false VA45 4.052,3.375 4.698,3.656 0.646,0.281 10 false VA46 4.604,0.198 5.135,0.844 0.531,0.646 10 false VA47 4.604,0.667 5.135,1.313 0.531,0.646 10 false VA48 3.688,3.552 4.188,3.74 0.5,0.188 10 false VA49 3.865,0.094 4.396,0.74 0.531,0.646 10 false VA50 4.135,0.344 4.667,0.99 0.531,0.646 10 false VA51 3.417,3.375 4.094,3.552 0.677,0.177 10 false VA52 3.365,0.073 3.896,0.719 0.531,0.646 10 false VA53 3.063,0.365 3.594,1.01 0.531,0.646 10 false VA54 3,3.573 3.677,3.75 0.677,0.177 10 false VA55 2.708,0.073 3.24,0.719 0.531,0.646 10 false VA56 2.531,0.427 3.063,1.073 0.531,0.646 10 false VA57 2.698,3.375 3.375,3.552 0.677,0.177 10 false VA58 2.156,0.167 2.688,0.813 0.531,0.646 10 false VA59 2.156,0.635 2.688,1.281 0.531,0.646 10 false VA60 2.25,3.583 2.729,3.781 0.479,0.198 10 false VA61 1.625,0.469 2.156,1.115 0.531,0.646 10 false VA62 1.281,3.01 1.813,3.656 0.531,0.646 10 false VA63 1.99,3.375 2.583,3.688 0.594,0.313 10 false VA64 1.5,0.854 2.031,1.5 0.531,0.646 10 false VA65 1.365,1.5 1.896,2.146 0.531,0.646 10 false VA66 1.427,3.417 1.917,3.677 0.49,0.26 10 false VA67 1.438,1.177 1.969,1.823 0.531,0.646 10 false VA68 1.156,2.021 1.688,2.667 0.531,0.646 10 false VA69 1.219,2.5 1.708,2.76 0.49,0.26 10 false VA70
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
HV Battery Cell Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
36 z13-1 (VAD) (-) - z13-13 (VA36) (+) Always 50 kΩ or more
37 z13-13 (VA36) (-) - z13-25 (VA37) (+) Always 50 kΩ or more
38 z13-25 (VA37) (-) - z13-2 (VA38) (+) Always 50 kΩ or more
39 z13-2 (VA38) (-) - z13-14 (VA39) (+) Always 50 kΩ or more
40 z13-14 (VA39) (-) - z13-26 (VA40) (+) Always 50 kΩ or more
41 z13-26 (VA40) (-) - z13-3 (VA41) (+) Always 50 kΩ or more
42 z13-3 (VA41) (-) - z13-15 (VA42) (+) Always 50 kΩ or more
43 z13-15 (VA42) (-) - z13-27 (VA43) (+) Always 50 kΩ or more
44 z13-27 (VA43) (-) - z13-4 (VA44) (+) Always 50 kΩ or more
45 z13-4 (VA44) (-) - z13-16 (VA45) (+) Always 50 kΩ or more
46 z13-16 (VA45) (-) - z13-28 (VA46) (+) Always 50 kΩ or more
47 z13-28 (VA46) (-) - z13-5 (VA47) (+) Always 50 kΩ or more
48 z13-5 (VA47) (-) - z13-17 (VA48) (+) Always 50 kΩ or more
49 z13-17 (VA48) (-) - z13-29 (VA49) (+) Always 50 kΩ or more
50 z13-29 (VA49) (-) - z13-6 (VA50) (+) Always 50 kΩ or more
51 z13-6 (VA50) (-) - z13-18 (VA51) (+) Always 50 kΩ or more
52 z13-18 (VA51) (-) - z13-30 (VA52) (+) Always 50 kΩ or more
53 z13-30 (VA52) (-) - z13-7 (VA53) (+) Always 50 kΩ or more
54 z13-7 (VA53) (-) - z13-19 (VA54) (+) Always 50 kΩ or more
55 z13-19 (VA54) (-) - z13-31 (VA55) (+) Always 50 kΩ or more
56 z13-31 (VA55) (-) - z13-8 (VA56) (+) Always 50 kΩ or more
57 z13-8 (VA56) (-) - z13-20 (VA57) (+) Always 50 kΩ or more
58 z13-20 (VA57) (-) - z13-32 (VA58) (+) Always 50 kΩ or more
59 z13-32 (VA58) (-) - z13-9 (VA59) (+) Always 50 kΩ or more
60 z13-9 (VA59) (-) - z13-21 (VA60) (+) Always 50 kΩ or more
61 z13-21 (VA60) (-) - z13-33 (VA61) (+) Always 50 kΩ or more
62 z13-33 (VA61) (-) - z13-10 (VA62) (+) Always 50 kΩ or more
63 z13-10 (VA62) (-) - z13-22 (VA63) (+) Always 50 kΩ or more
64 z13-22 (VA63) (-) - z13-34 (VA64) (+) Always 50 kΩ or more
65 z13-34 (VA64) (-) - z13-11 (VA65) (+) Always 50 kΩ or more
66 z13-11 (VA65) (-) - z13-23 (VA66) (+) Always 50 kΩ or more
67 z13-23 (VA66) (-) - z13-35 (VA67) (+) Always 50 kΩ or more
68 z13-35 (VA67) (-) - z13-12 (VA68) (+) Always 50 kΩ or more
69 z13-12 (VA68) (-) - z13-24 (VA69) (+) Always 50 kΩ or more
70 z13-24 (VA69) (-) - z13-36 (VA70) (+) Always 50 kΩ or more


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery ECU assembly.




c.

Install the battery ECU assembly.


Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



A

9.CHECK TOTAL DISTANCE DRIVEN

B

9.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1
Other than above B


HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.



A

B

10.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
10.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT