Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442936 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  U115087  Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message  


DESCRIPTION

The battery ECU assembly transmits and receives signals via CAN communication to and from the hybrid vehicle control ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U115087 Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message The battery ECU assembly does not receive any signals from the hybrid vehicle control ECU assembly for 1 second or more.
(1 trip detection logic)
·

Battery ECU assembly

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A404426E02
0.875,4.198 3.125,4.729 2.25,0.531 10 false CAN Communication Line 0.896,3.156 2.208,3.563 1.313,0.406 10 false Auxiliary Battery 1.573,1.26 2.51,1.896 0.938,0.635 10 false IGCT 2.615,1.854 3.552,2.49 0.938,0.635 10 false IGCT 3.802,1.281 4.74,1.917 0.938,0.635 10 false PM-IGCT 5.719,0.708 6.656,1.344 0.938,0.635 10 false +B1 5.74,1.125 6.677,1.76 0.938,0.635 10 false +B2 5.76,1.542 6.698,2.177 0.938,0.635 10 false MREL 5.74,2.646 6.677,3.281 0.938,0.635 10 false CA4H 5.76,3.219 6.698,3.854 0.938,0.635 10 false CA4L 3,3.208 3.938,3.844 0.938,0.635 10 false CA1L 2.979,2.646 3.917,3.281 0.938,0.635 10 false CA1H 2.156,3.729 4.146,4.24 1.99,0.51 10 false z16 Battery ECU Assembly 5.083,3.729 6.99,4.219 1.906,0.49 10 false Hybrid Vehicle Control ECU 5.427,0.5 5.833,0.76 0.406,0.26 10 false 4 5.438,0.927 5.844,1.188 0.406,0.26 10 false 1 5.354,0.688 5.76,0.948 0.406,0.26 10 false A29 5.365,1.115 5.771,1.375 0.406,0.26 10 false A28 5.354,1.51 5.76,1.771 0.406,0.26 10 false A29 5.427,1.333 5.833,1.594 0.406,0.26 10 false 6 5.354,2.646 5.76,2.906 0.406,0.26 10 false K69 5.406,2.448 5.813,2.708 0.406,0.26 10 false 34 5.385,3.021 5.792,3.281 0.406,0.26 10 false 35 5.365,3.229 5.771,3.49 0.406,0.26 10 false K69 3.51,2.5 3.917,2.76 0.406,0.26 10 false 25 3.5,3.052 3.906,3.313 0.406,0.26 10 false 26 5.094,3.906 7,4.396 1.906,0.49 10 false Assembly 2.313,1.031 2.719,1.292 0.406,0.26 10 false 3 3.073,1.01 3.479,1.271 0.406,0.26 10 false 5 3.073,1.417 3.479,1.677 0.406,0.26 10 false 1 3.781,1.021 4.188,1.281 0.406,0.26 10 false 1 2.323,1.406 2.729,1.667 0.406,0.26 10 false 2 4.25,1.01 4.656,1.271 0.406,0.26 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check and record any Hybrid Control DTCs and freeze frame data. Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs related to Hybrid Control System are not output. A
DTCs related to Hybrid Control System are output. B



e.

Turn the power switch off.



A

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (VOLTAGE)

B

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (VOLTAGE)
a.

Turn the power switch on (IG).


b.
A389500C94
0.531,0.854 1.031,1.104 0.5,0.25 1.156,0.865 1.656,1.115 0.5,0.25 0.792,2.625 0.99,1.708 true 1.667,2.635 1.406,1.708 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.729,2.667 1.49,3.073 0.76,0.406 10 false +B2 1.604,2.708 2.188,3.052 0.583,0.344 10 false +B1 0.667,0.896 1.031,1.156 0.365,0.26 10 false A28 1.271,0.906 1.604,1.073 0.333,0.167 10 false A29
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-4 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A28-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A407388C22
1.49,0.354 1.938,0.594 0.448,0.24 1.167,2.396 0.542,3.021 true 1.375,3.031 1.292,2.406 true 2.115,3.073 1.375,2.396 true 0.146,0.115 0.604,0.531 0.458,0.417 10 false *a 1.594,0.396 2.063,0.656 0.469,0.26 10 false z16 0.281,3.094 0.969,3.313 0.688,0.219 10 false CA1H 1.229,3.094 1.844,3.302 0.615,0.208 10 false CA1L 2.01,3.115 2.625,3.323 0.615,0.208 10 false GND
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-25 (CA1H) - z16-26 (CA1L) Power switch off 108 to 132 Ω



e.

Reconnect the z16 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BATTERY ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the K69 hybrid vehicle control ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.




d.
A406229N06
2.281,0.969 2.698,1.219 0.417,0.25 2.344,0.99 2.635,1.188 0.292,0.198 10 true z16

Disconnect the z16 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A407398C02
1.5,0.094 1.896,0.375 0.396,0.281 1.854,2.375 2.25,2.656 0.396,0.281 0.438,1.563 1.25,1.74 true 0.344,0.906 1.365,1.75 true 1.167,4.26 1.833,4.052 true 2.604,4.292 1.896,4.052 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.083,2.083 0.396,2.281 0.313,0.198 10 false *b 1.594,0.156 1.906,0.354 0.313,0.198 10 false z16 1.917,2.427 2.229,2.625 0.313,0.198 10 false K69 0.031,1.458 0.615,1.948 0.583,0.49 10 false CA1H 0.865,4.313 1.344,4.51 0.479,0.198 10 false CA4L 0.031,0.719 0.667,1.146 0.635,0.427 10 false CA1L 2.625,4.323 3.104,4.521 0.479,0.198 10 false CA4H
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z16-25 (CA1H) - K69-34 (CA4H) Power switch off Below 1 Ω
z16-26 (CA1L) - K69-35 (CA4L) Power switch off Below 1 Ω
z16-25 (CA1H) - Other terminals and body ground Power switch off 10 kΩ or higher
z16-26 (CA1L) - Other terminals and body ground Power switch off 10 kΩ or higher



f.

Reconnect the z16 battery ECU assembly connector.


g.

Install the No. 1 HV battery hose.


h.

Reconnect the K69 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR