Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442936 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P1AC413  Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open  P1AC513  Hybrid/EV Battery Stack 2 Current Interrupt Device Circuit Open  


DESCRIPTION

The battery ECU assembly restricts charging and discharging of the HV battery and stores a DTC when a current interrupt device (CID) located in an HV battery cell has operated and the high voltage circuit is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1AC413 Hybrid/EV Battery Stack 1 Current Interrupt Device Circuit Open A shut-off by a CID occurs.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on
P1AC513 Hybrid/EV Battery Stack 2 Current Interrupt Device Circuit Open A shut-off by a CID occurs.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P1AC413
·

Hybrid/EV Battery Cell 1 to 70 Voltage

·

Hybrid/EV Battery Cell 1 to 70 Internal Resistance


P1AC513

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and wait for 10 seconds or more.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (READY) and turn the GTS on.

8.

With power switch on (READY) and wait for 30 seconds or more.

9.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Do not turn the power switch on (READY) until the repair is completed.



PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P1AC413 or P1AC513" only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


e.

Turn the power switch off.



A

2.CHECK DTC

B

C

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P1AC413" is also output. A
"P1AC513" is also output. B



A

3.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 1 TO 35 VOLTAGE)

B

8.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 36 TO 70 VOLTAGE)
3.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 1 TO 35 VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

NOTICE:

Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Cell 1 to 35 Voltage.


d.

Read the value of data list items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 35 Voltage" and make a note if the value of any is 1.6 V or less.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
50003 398 92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406228N02
1.979,0.76 2.323,1.021 0.344,0.26 2,0.792 2.281,0.979 0.281,0.188 10 true z15

Check the connector connections and contact pressure of the relevant terminals for the battery ECU assembly.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



d.

Install the No. 1 HV battery hose.



A

5.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY CELL VOLTAGE)

B

CONNECT SECURELY

C

5.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY CELL VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the HV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each HV battery cell.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406228N02
1.979,0.76 2.323,1.021 0.344,0.26 2,0.792 2.281,0.979 0.281,0.188 10 true z15

Disconnect the z15 battery ECU assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the HV battery cells whose value in the data list was 1.6 V or less only.


A407537C09
0.448,1.844 0.865,2.094 0.417,0.25 1.625,1.51 2.917,2.094 true 1.51,2.448 2.927,2.25 true 1.615,2.729 2.927,2.344 true 1.698,1.219 3.021,2.073 true 1.458,2.063 3.01,2.208 true 1.74,3.021 3.052,2.354 true 1.729,0.917 3.125,2.094 true 1.479,1.76 3.135,2.208 true 1.948,3.271 3.146,2.354 true 2.156,0.469 3.24,2.073 true 2.25,0.844 3.24,2.198 true 2.292,3.427 3.24,2.365 true 2.677,0.302 3.344,2.083 true 2.656,0.552 3.333,2.208 true 2.771,3.302 3.344,2.354 true 3.438,0.25 3.469,2.083 true 3.021,0.24 3.438,2.219 true 3.135,3.469 3.469,2.344 true 3.74,0.24 3.552,2.083 true 4.115,0.271 3.573,2.208 true 3.531,3.354 3.552,2.354 true 4.531,0.354 3.688,2.083 true 4.948,0.885 3.677,2.219 true 3.958,3.51 3.667,2.333 true 4.76,0.615 3.75,2.073 true 5.375,1.708 3.781,2.219 true 4.229,3.365 3.771,2.344 true 5.177,1.083 3.875,2.104 true 5.313,2.604 3.865,2.24 true 4.719,3.49 3.875,2.354 true 5.313,1.281 3.969,2.083 true 5.344,1.927 3.969,2.208 true 4.938,3.24 3.969,2.354 true 5.354,1.49 4.073,2.083 true 5.406,2.229 4.073,2.229 true 5.094,2.885 4.094,2.354 true 0.26,0.135 0.729,0.552 0.469,0.417 10 false *a 1.323,1.396 1.76,1.75 0.438,0.354 10 false GA0 1.24,2.385 1.677,2.74 0.438,0.354 10 false VA1 0.552,1.885 0.99,2.24 0.438,0.354 10 false z15 1.333,2.688 1.771,3.042 0.438,0.354 10 false VA2 1.417,1.125 1.854,1.479 0.438,0.354 10 false VA3 1.177,1.99 1.615,2.344 0.438,0.354 10 false VA4 1.448,2.979 1.885,3.333 0.438,0.354 10 false VA5 1.448,0.813 1.885,1.167 0.438,0.354 10 false VA6 1.188,1.677 1.625,2.031 0.438,0.354 10 false VA7 1.677,3.229 2.115,3.583 0.438,0.354 10 false VA8 1.865,0.385 2.302,0.74 0.438,0.354 10 false VA9 1.906,0.708 2.344,1.063 0.438,0.354 10 false VA10 2.042,3.448 2.479,3.802 0.438,0.354 10 false VA11 2.448,0.135 2.885,0.49 0.438,0.354 10 false VA12 2.344,0.396 2.781,0.75 0.438,0.354 10 false VA13 2.563,3.323 3,3.677 0.438,0.354 10 false VA14 3.229,0.083 3.667,0.438 0.438,0.354 10 false VA15 2.813,0.073 3.25,0.427 0.438,0.354 10 false VA16 2.969,3.5 3.344,3.74 0.375,0.24 10 false VA17 3.635,0.073 4.073,0.427 0.438,0.354 10 false VA18 4.125,0.115 4.563,0.469 0.438,0.354 10 false VA19 3.396,3.375 3.875,3.667 0.479,0.292 10 false VA20 4.563,0.208 5,0.563 0.438,0.354 10 false VA21 4.979,0.75 5.417,1.104 0.438,0.354 10 false VA22 3.833,3.552 4.25,3.802 0.417,0.25 10 false VA23 4.792,0.479 5.229,0.833 0.438,0.354 10 false VA24 5.406,1.625 5.844,1.979 0.438,0.354 10 false VA25 4.125,3.385 4.563,3.74 0.438,0.354 10 false VA26 5.219,0.958 5.656,1.313 0.438,0.354 10 false VA27 5.365,2.552 5.802,2.906 0.438,0.354 10 false VA28 4.625,3.531 5.073,3.802 0.448,0.271 10 false VA29 5.354,1.177 5.792,1.531 0.438,0.354 10 false VA30 5.406,1.844 5.844,2.198 0.438,0.354 10 false VA31 4.854,3.26 5.292,3.615 0.438,0.354 10 false VA32 5.417,1.396 5.854,1.75 0.438,0.354 10 false VA33 5.458,2.146 5.896,2.5 0.438,0.354 10 false VA34 5.125,2.906 5.563,3.26 0.438,0.354 10 false VA35
*a Front view of wire harness connector
(to Battery ECU Assembly)
- -


HV Battery Cell Tester Connection Condition
1 z15-1 (GA0) - z15-13 (VA1) Always
2 z15-13 (VA1) - z15-25 (VA2) Always
3 z15-25 (VA2) - z15-2 (VA3) Always
4 z15-2 (VA3) - z15-14 (VA4) Always
5 z15-14 (VA4) - z15-26 (VA5) Always
6 z15-26 (VA5) - z15-3 (VA6) Always
7 z15-3 (VA6) - z15-15 (VA7) Always
8 z15-15 (VA7) - z15-27 (VA8) Always
9 z15-27 (VA8) - z15-4 (VA9) Always
10 z15-4 (VA9) - z15-16 (VA10) Always
11 z15-16 (VA10) - z15-28 (VA11) Always
12 z15-28 (VA11) - z15-5 (VA12) Always
13 z15-5 (VA12) - z15-17 (VA13) Always
14 z15-17 (VA13) - z15-29 (VA14) Always
15 z15-29 (VA14) - z15-6 (VA15) Always
16 z15-6 (VA15) - z15-18 (VA16) Always
17 z15-18 (VA16) - z15-30(VA17) Always
18 z15-30(VA17) - z15-7 (VA18) Always
19 z15-7 (VA18) - z15-19 (VA19) Always
20 z15-19 (VA19) - z15-31 (VA20) Always
21 z15-31 (VA20) - z15-8 (VA21) Always
22 z15-8 (VA21) - z15-20(VA22) Always
23 z15-20(VA22) - z15-32 (VA23) Always
24 z15-32 (VA23) - z15-9 (VA24) Always
25 z15-9 (VA24) - z15-21 (VA25) Always
26 z15-21 (VA25) - z15-33 (VA26) Always
27 z15-33 (VA26) - z15-10(VA27) Always
28 z15-10(VA27) - z15-22 (VA28) Always
29 z15-22 (VA28) - z15-34 (VA29) Always
30 z15-34 (VA29) - z15-11 (VA30) Always
31 z15-11 (VA30) - z15-23 (VA31) Always
32 z15-23 (VA31) - z15-35 (VA32) Always
33 z15-35 (VA32) - z15-12 (VA33) Always
34 z15-12 (VA33) - z15-24 (VA34) Always
35 z15-24 (VA34) - z15-36 (VA35) Always

CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.


Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



e.

Reconnect the z15 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.



A

6.CHECK BATTERY ECU ASSEMBLY (GA0 - VA35)

B

6.CHECK BATTERY ECU ASSEMBLY (GA0 - VA35)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage.



b.

Measure the voltage according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured 1.6 V or less in the previous step.


A407538C07
0.448,1.802 0.875,2.052 0.427,0.25 4.667,1.948 5.563,2.094 true 4.479,1.885 5.719,1.625 true 4.083,2.021 4.677,3.552 true 4.656,1.729 5.688,1.281 true 3.906,1.875 4.76,0.323 true 3.729,1.99 3.833,3.281 true 4.646,2.219 5.354,2.604 true 4.448,1.656 5.156,0.875 true 4.417,2.219 5.354,3.177 true 4.281,1.646 5.219,0.5 true 4.292,1.906 5.531,0.948 true 4.25,2.208 5,3.25 true 4.094,1.667 4.802,0.729 true 4.052,2.219 4.323,3.271 true 3.896,1.625 4.281,0.448 true 3.885,2.219 4.104,3.583 true 3.729,1.625 4.094,0.26 true 3.656,2.24 3.5,3.531 true 3.542,1.656 3.688,0.25 true 3.448,1.844 3.385,0.49 true 3.49,2.25 3.292,3.281 true 3.281,1.625 3.083,0.25 true 3.281,2.01 2.76,3.26 true 3.313,2.229 2.917,3.521 true 3.135,1.625 2.76,0.344 true 3.104,1.865 2.406,0.396 true 3.115,2.219 2.229,3.51 true 2.927,1.635 2.042,0.563 true 2.906,2.01 1.635,2.823 true 2.896,2.229 1.813,3.406 true 2.76,1.635 1.896,0.865 true 2.719,1.865 1.625,1.521 true 2.708,2.198 1.823,3.083 true 2.531,1.615 1.698,1.177 true 1.594,1.865 2.51,1.927 true 2.51,2.156 1.573,2.406 true 0.094,0.052 0.719,0.542 0.625,0.49 10 false *a 0.542,1.844 0.979,2.177 0.438,0.333 10 false z15 5.74,1.188 6.177,1.521 0.438,0.333 10 false GA0 5.615,2.021 6.052,2.354 0.438,0.333 10 false VA1 4.938,3.302 5.375,3.635 0.438,0.333 10 false VA8 5.406,2.604 5.844,2.938 0.438,0.333 10 false VA2 5.219,0.771 5.656,1.104 0.438,0.333 10 false VA3 5.573,0.844 6.01,1.177 0.438,0.333 10 false VA7 5.76,1.542 6.198,1.875 0.438,0.333 10 false VA4 5.385,3.177 5.823,3.51 0.438,0.333 10 false VA5 5.25,0.365 5.688,0.698 0.438,0.333 10 false VA6 4.75,0.563 5.188,0.896 0.438,0.333 10 false VA9 4.552,3.583 5.01,3.771 0.458,0.188 10 false VA10 4.198,3.302 4.646,3.542 0.448,0.24 10 false VA11 4.208,0.292 4.646,0.625 0.438,0.333 10 false VA12 4.771,0.167 5.208,0.5 0.438,0.333 10 false VA13 3.969,3.594 4.469,3.781 0.5,0.188 10 false VA14 3.979,0.094 4.448,0.365 0.469,0.271 10 false VA15 3.698,3.313 4.167,3.583 0.469,0.271 10 false VA16 3.344,3.552 3.813,3.76 0.469,0.208 10 false VA17 3.521,0.094 3.99,0.365 0.469,0.271 10 false VA18 3.198,0.323 3.667,0.594 0.469,0.271 10 false VA19 3.115,3.302 3.583,3.51 0.469,0.208 10 false VA20 2.896,0.094 3.365,0.365 0.469,0.271 10 false VA21 2.552,3.271 3.063,3.49 0.51,0.219 10 false VA22 2.74,3.563 3.208,3.771 0.469,0.208 10 false VA23 2.521,0.177 2.99,0.448 0.469,0.271 10 false VA24 2.083,0.26 2.552,0.531 0.469,0.271 10 false VA25 2.021,3.542 2.5,3.771 0.479,0.229 10 false VA26 1.708,0.458 2.177,0.729 0.469,0.271 10 false VA27 1.26,2.76 1.729,3.031 0.469,0.271 10 false VA28 1.573,3.438 2.042,3.708 0.469,0.271 10 false VA29 1.552,0.75 2.021,1.021 0.469,0.271 10 false VA30 1.281,1.448 1.75,1.719 0.469,0.271 10 false VA31 1.469,3.094 1.938,3.365 0.469,0.271 10 false VA32 1.354,1.083 1.823,1.354 0.469,0.271 10 false VA33 1.229,1.792 1.698,2.063 0.469,0.271 10 false VA34 1.208,2.344 1.677,2.615 0.469,0.271 10 false VA35
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Voltage:
HV Battery Cell Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
1 z15-1 (GA0) (+) - z15-13 (VA1) (-) Always 0.3 to 1.0 V
2 z15-13 (VA1) (+) - z15-25 (VA2) (-) Always 0.3 to 1.0 V
3 z15-25 (VA2) (+) - z15-2 (VA3) (-) Always 0.3 to 1.0 V
4 z15-2 (VA3) (+) - z15-14 (VA4) (-) Always 0.3 to 1.0 V
5 z15-14 (VA4) (+) - z15-26 (VA5) (-) Always 0.3 to 1.0 V
6 z15-26 (VA5) (+) - z15-3 (VA6) (-) Always 0.3 to 1.0 V
7 z15-3 (VA6) (+) - z15-15 (VA7) (-) Always 0.3 to 1.0 V
8 z15-15 (VA7) (+) - z15-27 (VA8) (-) Always 0.3 to 1.0 V
9 z15-27 (VA8) (+) - z15-4 (VA9) (-) Always 0.3 to 1.0 V
10 z15-4 (VA9) (+) - z15-16 (VA10) (-) Always 0.3 to 1.0 V
11 z15-16 (VA10) (+) - z15-28 (VA11) (-) Always 0.3 to 1.0 V
12 z15-28 (VA11) (+) - z15-5 (VA12) (-) Always 0.3 to 1.0 V
13 z15-5 (VA12) (+) - z15-17 (VA13) (-) Always 0.3 to 1.0 V
14 z15-17 (VA13) (+) - z15-29 (VA14) (-) Always 0.3 to 1.0 V
15 z15-29 (VA14) (+) - z15-6 (VA15) (-) Always 0.3 to 1.0 V
16 z15-6 (VA15) (+) - z15-18 (VA16) (-) Always 0.3 to 1.0 V
17 z15-18 (VA16) (+) - z15-30 (VA17) (-) Always 0.3 to 1.0 V
18 z15-30 (VA17) (+) - z15-7 (VA18) (-) Always 0.3 to 1.0 V
19 z15-7 (VA18) (+) - z15-19 (VA19) (-) Always 0.3 to 1.0 V
20 z15-19 (VA19) (+) - z15-31 (VA20) (-) Always 0.3 to 1.0 V
21 z15-31 (VA20) (+) - z15-8 (VA21) (-) Always 0.3 to 1.0 V
22 z15-8 (VA21) (+) - z15-20 (VA22) (-) Always 0.3 to 1.0 V
23 z15-20 (VA22) (+) - z15-32 (VA23) (-) Always 0.3 to 1.0 V
24 z15-32 (VA23) (+) - z15-9 (VA24) (-) Always 0.3 to 1.0 V
25 z15-9 (VA24) (+) - z15-21 (VA25) (-) Always 0.3 to 1.0 V
26 z15-21 (VA25) (+) - z15-33 (VA26) (-) Always 0.3 to 1.0 V
27 z15-33 (VA26) (+) - z15-10 (VA27) (-) Always 0.3 to 1.0 V
28 z15-10 (VA27) (+) - z15-22 (VA28) (-) Always 0.3 to 1.0 V
29 z15-22 (VA28) (+) - z15-34 (VA29) (-) Always 0.3 to 1.0 V
30 z15-34 (VA29) (+) - z15-11 (VA30) (-) Always 0.3 to 1.0 V
31 z15-11 (VA30) (+) - z15-23 (VA31) (-) Always 0.3 to 1.0 V
32 z15-23 (VA31) (+) - z15-35 (VA32) (-) Always 0.3 to 1.0 V
33 z15-35 (VA32) (+) - z15-12 (VA33) (-) Always 0.3 to 1.0 V
34 z15-12 (VA33) (+) - z15-24 (VA34) (-) Always 0.3 to 1.0 V
35 z15-24 (VA34) (+) - z15-36 (VA35) (-) Always 0.3 to 1.0 V


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Be sure to set the toyota electrical tester to diode range when performing this test.

·

Read the voltage after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of the battery ECU assembly.



Result:
Result Proceed to
The voltage between the terminals is 0.3 to 1.0 V. A
Other than above B



c.

Install the battery ECU assembly.



A

B

7.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
8.READ VALUE USING GTS (HYBRID/EV BATTERY CELL 36 TO 70 VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

NOTICE:

Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Cell 36 to 70 Voltage.


d.

Read the value of data list items "Hybrid/EV Battery Cell 36 Voltage" through "Hybrid/EV Battery Cell 70 Voltage" and make a note if the value of any is 1.6 V or less.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
Hybrid/EV Battery Cell 49 Voltage
Hybrid/EV Battery Cell 50 Voltage
Hybrid/EV Battery Cell 51 Voltage
Hybrid/EV Battery Cell 52 Voltage
Hybrid/EV Battery Cell 53 Voltage
Hybrid/EV Battery Cell 54 Voltage
Hybrid/EV Battery Cell 55 Voltage
Hybrid/EV Battery Cell 56 Voltage
Hybrid/EV Battery Cell 57 Voltage
Hybrid/EV Battery Cell 58 Voltage
Hybrid/EV Battery Cell 59 Voltage
Hybrid/EV Battery Cell 60 Voltage
Hybrid/EV Battery Cell 61 Voltage
Hybrid/EV Battery Cell 62 Voltage
Hybrid/EV Battery Cell 63 Voltage
Hybrid/EV Battery Cell 64 Voltage
Hybrid/EV Battery Cell 65 Voltage
Hybrid/EV Battery Cell 66 Voltage
Hybrid/EV Battery Cell 67 Voltage
Hybrid/EV Battery Cell 68 Voltage
Hybrid/EV Battery Cell 69 Voltage
Hybrid/EV Battery Cell 70 Voltage
50003 398 369,370,371,372,373,374,375,376,377,378,379,380,381,382,383,384,385,386,387,388,389,390,391,392,393,394,395,396,397,398,399,400,401,402,403

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

9.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
9.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406227N06
1.667,0.552 2.031,0.792 0.365,0.24 1.698,0.583 1.979,0.75 0.281,0.167 10 true z13

Check the connector connections and contact pressure of the relevant terminals for the battery ECU assembly.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



d.

Install the No. 1 HV battery hose.



A

10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY CELL VOLTAGE)

B

CONNECT SECURELY

C

10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY CELL VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the HV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each HV battery cell.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A406227N06
1.667,0.552 2.031,0.792 0.365,0.24 1.698,0.583 1.979,0.75 0.281,0.167 10 true z13

Disconnect the z13 battery ECU assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the HV battery cells whose value in the data list was 1.6 V or less only.


A407535C07
0.365,1.948 0.792,2.208 0.427,0.26 2.948,2.208 1.885,1.521 true 2.938,2.365 1.865,2.531 true 2.969,2.479 1.948,2.906 true 3.073,2.198 1.979,1.281 true 3.073,2.344 1.823,2.135 true 3.083,2.479 2.104,3.083 true 3.167,2.208 2.135,1 true 2.646,3.354 3.281,2.365 true 3.177,2.479 2.333,3.25 true 3.271,2.188 2.271,0.771 true 3.281,2.469 2.896,3.521 true 3.385,2.188 2.813,0.542 true 3.375,2.323 2.719,0.792 true 3.375,2.479 3.208,3.313 true 3.5,2.198 3.271,0.302 true 3.49,2.333 2.948,0.385 true 3.49,2.479 3.427,3.542 true 3.573,2.188 3.74,0.292 true 3.594,2.344 4.115,0.323 true 3.594,2.479 3.667,3.344 true 3.698,2.208 4.375,0.51 true 3.708,2.323 4.521,0.75 true 3.698,2.479 3.948,3.531 true 3.813,2.198 5.031,0.708 true 3.823,2.323 5.198,1.167 true 3.177,2.323 1.896,1.865 true 3.802,2.5 4.25,3.385 true 3.885,2.208 5.229,0.865 true 3.896,2.344 5.469,1.958 true 3.896,2.5 4.667,3.448 true 4.01,2.24 5.323,1.417 true 4.031,2.375 5.167,2.677 true 4.01,2.479 4.875,3.26 true 4.125,2.219 5.438,1.677 true 5.354,2.323 4.135,2.333 true 4.125,2.469 5.125,3.063 true 0.365,0.125 0.792,0.521 0.427,0.396 10 false *a 0.458,1.99 0.885,2.302 0.427,0.313 10 false z13 1.573,1.417 2,1.813 0.427,0.396 10 false VAD 1.49,2.458 1.917,2.854 0.427,0.396 10 false VA36 1.604,2.865 2.031,3.26 0.427,0.396 10 false VA37 1.615,1.188 2.042,1.583 0.427,0.396 10 false VA38 1.448,2.042 1.875,2.438 0.427,0.396 10 false VA39 1.76,3.083 2.188,3.479 0.427,0.396 10 false VA40 1.781,0.885 2.208,1.281 0.427,0.396 10 false VA41 1.531,1.792 1.958,2.188 0.427,0.396 10 false VA42 2.021,3.271 2.469,3.542 0.448,0.271 10 false VA43 1.938,0.625 2.365,1.021 0.427,0.396 10 false VA44 2.406,3.375 2.865,3.594 0.458,0.219 10 false VA45 2.688,3.521 3.146,3.74 0.458,0.219 10 false VA46 2.479,0.427 2.906,0.823 0.427,0.396 10 false VA47 2.365,0.667 2.792,1.063 0.427,0.396 10 false VA48 3.052,3.333 3.51,3.552 0.458,0.219 10 false VA49 3.063,0.146 3.49,0.542 0.427,0.396 10 false VA50 2.646,0.229 3.094,0.625 0.448,0.396 10 false VA51 3.271,3.563 3.76,3.781 0.49,0.219 10 false VA52 3.625,0.125 4.052,0.521 0.427,0.396 10 false VA53 4.115,0.167 4.542,0.563 0.427,0.396 10 false VA54 3.531,3.365 4.021,3.583 0.49,0.219 10 false VA55 4.385,0.365 4.813,0.76 0.427,0.396 10 false VA56 4.563,0.625 5,1.01 0.438,0.385 10 false VA57 3.823,3.573 4.313,3.792 0.49,0.219 10 false VA58 5.063,0.573 5.49,0.969 0.427,0.396 10 false VA59 5.25,1.052 5.656,1.25 0.406,0.198 10 false VA60 4.156,3.396 4.646,3.615 0.49,0.219 10 false VA61 5.271,0.74 5.677,0.938 0.406,0.198 10 false VA62 5.51,1.854 5.917,2.052 0.406,0.198 10 false VA63 4.542,3.49 4.948,3.688 0.406,0.198 10 false VA64 5.385,1.323 5.792,1.521 0.406,0.198 10 false VA65 5.208,2.635 5.615,2.833 0.406,0.198 10 false VA66 4.896,3.271 5.302,3.469 0.406,0.198 10 false VA67 5.479,1.573 5.885,1.771 0.406,0.198 10 false VA68 5.417,2.26 5.823,2.458 0.406,0.198 10 false VA69 5.167,3.042 5.573,3.24 0.406,0.198 10 false VA70
*a Front view of wire harness connector
(to Battery ECU Assembly)
- -


HV Battery Cell Tester Connection Condition
36 z13-1 (VAD) - z13-13 (VA36) Always
37 z13-13 (VA36) - z13-25 (VA37) Always
38 z13-25 (VA37) - z13-2 (VA38) Always
39 z13-2 (VA38) - z13-14 (VA39) Always
40 z13-14 (VA39) - z13-26 (VA40) Always
41 z13-26 (VA40) - z13-3 (VA41) Always
42 z13-3 (VA41) - z13-15 (VA42) Always
43 z13-15 (VA42) - z13-27 (VA43) Always
44 z13-27 (VA43) - z13-4 (VA44) Always
45 z13-4 (VA44) - z13-16 (VA45) Always
46 z13-16 (VA45) - z13-28 (VA46) Always
47 z13-28 (VA46) - z13-5 (VA47) Always
48 z13-5 (VA47) - z13-17 (VA48) Always
49 z13-17 (VA48) - z13-29 (VA49) Always
50 z13-29 (VA49) - z13-6 (VA50) Always
51 z13-6 (VA50) - z13-18 (VA51) Always
52 z13-18 (VA51) - z13-30 (VA52) Always
53 z13-30 (VA52) - z13-7 (VA53) Always
54 z13-7 (VA53) - z13-19 (VA54) Always
55 z13-19 (VA54) - z13-31 (VA55) Always
56 z13-31 (VA55) - z13-8 (VA56) Always
57 z13-8 (VA56) - z13-20 (VA57) Always
58 z13-20 (VA57) - z13-32 (VA58) Always
59 z13-32 (VA58) - z13-9 (VA59) Always
60 z13-9 (VA59) - z13-21 (VA60) Always
61 z13-21 (VA60) - z13-33 (VA61) Always
62 z13-33 (VA61) - z13-10 (VA62) Always
63 z13-10 (VA62) - z13-22 (VA63) Always
64 z13-22 (VA63) - z13-34 (VA64) Always
65 z13-34 (VA64) - z13-11 (VA65) Always
66 z13-11 (VA65) - z13-23 (VA66) Always
67 z13-23 (VA66) - z13-35 (VA67) Always
68 z13-35 (VA67) - z13-12 (VA68) Always
69 z13-12 (VA68) - z13-24 (VA69) Always
70 z13-24 (VA69) - z13-36 (VA70) Always

CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.


Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



e.

Reconnect the z13 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.



A

11.CHECK BATTERY ECU ASSEMBLY (VAD - VA70)

B

11.CHECK BATTERY ECU ASSEMBLY (VAD - VA70)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage.



b.

Measure the voltage according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured 1.6 V or less in the previous step.


A407536C07
0.333,1.927 0.698,2.177 0.365,0.25 4.604,1.885 5.917,1.552 true 4.625,2.104 5.719,2.198 true 4.625,2.333 5.615,2.583 true 4.427,1.865 5.802,1.25 true 4.427,2.052 5.896,1.854 true 4.365,2.385 5.073,3.281 true 4.24,1.844 5.469,0.781 true 4.25,2.177 5.417,2.969 true 4.198,2.406 4.708,3.521 true 4.083,1.833 5.271,0.5 true 4.073,2.042 5.271,1.188 true 4.01,2.385 4.188,3.365 true 3.875,1.813 4.688,0.344 true 3.854,2.031 4.698,0.823 true 3.833,2.406 3.844,3.531 true 3.646,1.802 3.99,0.25 true 3.677,2.042 4.26,0.521 true 3.656,2.406 3.583,3.365 true 3.479,1.833 3.542,0.24 true 3.427,2.031 3.229,0.521 true 3.469,2.385 3.188,3.552 true 3.281,1.792 2.927,0.229 true 3.26,2.042 2.729,0.583 true 3.281,2.406 2.896,3.354 true 3.083,1.792 2.375,0.333 true 3.094,2.021 2.365,0.792 true 3.094,2.396 2.469,3.563 true 2.865,1.823 1.969,0.625 true 2.875,2.156 1.656,3.021 true 2.896,2.396 2.198,3.354 true 2.719,1.802 1.865,0.958 true 2.708,2.031 1.729,1.604 true 2.688,2.396 1.74,3.406 true 2.521,1.813 1.802,1.271 true 1.552,2.094 2.51,2.094 true 2.5,2.323 1.604,2.552 true 0.344,0.115 0.875,0.76 0.531,0.646 10 false *a 0.438,1.969 0.854,2.302 0.417,0.333 10 false z13 5.656,2.542 6.156,2.792 0.5,0.25 10 false VA37 5.958,1.448 6.49,2.094 0.531,0.646 10 false VAD 5.76,2.135 6.24,2.365 0.479,0.229 10 false VA36 5.844,1.146 6.375,1.792 0.531,0.646 10 false VA38 5.938,1.76 6.458,2.01 0.521,0.25 10 false VA39 4.948,3.313 5.438,3.552 0.49,0.24 10 false VA40 5.5,0.677 6.031,1.323 0.531,0.646 10 false VA41 5.448,3 5.854,3.198 0.406,0.198 10 false VA42 4.615,3.542 5.083,3.719 0.469,0.177 10 false VA43 5.281,0.375 5.813,1.021 0.531,0.646 10 false VA44 5.323,1.104 5.854,1.75 0.531,0.646 10 false VA45 4.052,3.375 4.698,3.656 0.646,0.281 10 false VA46 4.604,0.198 5.135,0.844 0.531,0.646 10 false VA47 4.604,0.667 5.135,1.313 0.531,0.646 10 false VA48 3.688,3.552 4.188,3.74 0.5,0.188 10 false VA49 3.865,0.094 4.396,0.74 0.531,0.646 10 false VA50 4.135,0.344 4.667,0.99 0.531,0.646 10 false VA51 3.417,3.375 4.094,3.552 0.677,0.177 10 false VA52 3.365,0.073 3.896,0.719 0.531,0.646 10 false VA53 3.063,0.365 3.594,1.01 0.531,0.646 10 false VA54 3,3.573 3.677,3.75 0.677,0.177 10 false VA55 2.708,0.073 3.24,0.719 0.531,0.646 10 false VA56 2.531,0.427 3.063,1.073 0.531,0.646 10 false VA57 2.698,3.375 3.375,3.552 0.677,0.177 10 false VA58 2.156,0.167 2.688,0.813 0.531,0.646 10 false VA59 2.156,0.635 2.688,1.281 0.531,0.646 10 false VA60 2.25,3.583 2.729,3.781 0.479,0.198 10 false VA61 1.625,0.469 2.156,1.115 0.531,0.646 10 false VA62 1.281,3.01 1.813,3.656 0.531,0.646 10 false VA63 1.99,3.375 2.583,3.688 0.594,0.313 10 false VA64 1.5,0.854 2.031,1.5 0.531,0.646 10 false VA65 1.365,1.5 1.896,2.146 0.531,0.646 10 false VA66 1.427,3.417 1.917,3.677 0.49,0.26 10 false VA67 1.438,1.177 1.969,1.823 0.531,0.646 10 false VA68 1.156,2.021 1.688,2.667 0.531,0.646 10 false VA69 1.219,2.5 1.708,2.76 0.49,0.26 10 false VA70
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Voltage:
HV Battery Cell Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
36 z13-1 (VAD) (+) - z13-13 (VA36) (-) Always 0.3 to 1.0 V
37 z13-13 (VA36) (+) - z13-25 (VA37) (-) Always 0.3 to 1.0 V
38 z13-25 (VA37) (+) - z13-2 (VA38) (-) Always 0.3 to 1.0 V
39 z13-2 (VA38) (+) - z13-14 (VA39) (-) Always 0.3 to 1.0 V
40 z13-14 (VA39) (+) - z13-26 (VA40) (-) Always 0.3 to 1.0 V
41 z13-26 (VA40) (+) - z13-3 (VA41) (-) Always 0.3 to 1.0 V
42 z13-3 (VA41) (+) - z13-15 (VA42) (-) Always 0.3 to 1.0 V
43 z13-15 (VA42) (+) - z13-27 (VA43) (-) Always 0.3 to 1.0 V
44 z13-27 (VA43) (+) - z13-4 (VA44) (-) Always 0.3 to 1.0 V
45 z13-4 (VA44) (+) - z13-16 (VA45) (-) Always 0.3 to 1.0 V
46 z13-16 (VA45) (+) - z13-28 (VA46) (-) Always 0.3 to 1.0 V
47 z13-28 (VA46) (+) - z13-5 (VA47) (-) Always 0.3 to 1.0 V
48 z13-5 (VA47) (+) - z13-17 (VA48) (-) Always 0.3 to 1.0 V
49 z13-17 (VA48) (+) - z13-29 (VA49) (-) Always 0.3 to 1.0 V
50 z13-29 (VA49) (+) - z13-6 (VA50) (-) Always 0.3 to 1.0 V
51 z13-6 (VA50) (+) - z13-18 (VA51) (-) Always 0.3 to 1.0 V
52 z13-18 (VA51) (+) - z13-30 (VA52) (-) Always 0.3 to 1.0 V
53 z13-30 (VA52) (+) - z13-7 (VA53) (-) Always 0.3 to 1.0 V
54 z13-7 (VA53) (+) - z13-19 (VA54) (-) Always 0.3 to 1.0 V
55 z13-19 (VA54) (+) - z13-31 (VA55) (-) Always 0.3 to 1.0 V
56 z13-31 (VA55) (+) - z13-8 (VA56) (-) Always 0.3 to 1.0 V
57 z13-8 (VA56) (+) - z13-20 (VA57) (-) Always 0.3 to 1.0 V
58 z13-20 (VA57) (+) - z13-32 (VA58) (-) Always 0.3 to 1.0 V
59 z13-32 (VA58) (+) - z13-9 (VA59) (-) Always 0.3 to 1.0 V
60 z13-9 (VA59) (+) - z13-21 (VA60) (-) Always 0.3 to 1.0 V
61 z13-21 (VA60) (+) - z13-33 (VA61) (-) Always 0.3 to 1.0 V
62 z13-33 (VA61) (+) - z13-10 (VA62) (-) Always 0.3 to 1.0 V
63 z13-10 (VA62) (+) - z13-22 (VA63) (-) Always 0.3 to 1.0 V
64 z13-22 (VA63) (+) - z13-34 (VA64) (-) Always 0.3 to 1.0 V
65 z13-34 (VA64) (+) - z13-11 (VA65) (-) Always 0.3 to 1.0 V
66 z13-11 (VA65) (+) - z13-23 (VA66) (-) Always 0.3 to 1.0 V
67 z13-23 (VA66) (+) - z13-35 (VA67) (-) Always 0.3 to 1.0 V
68 z13-35 (VA67) (+) - z13-12 (VA68) (-) Always 0.3 to 1.0 V
69 z13-12 (VA68) (+) - z13-24 (VA69) (-) Always 0.3 to 1.0 V
70 z13-24 (VA69) (+) - z13-36 (VA70) (-) Always 0.3 to 1.0 V


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Be sure to set the toyota electrical tester to diode range when performing this test.

·

Read the voltage after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of the battery ECU assembly.



Result:
Result Proceed to
The voltage between the terminals is 0.3 to 1.0 V. A
Other than above B



c.

Install the battery ECU assembly.



A

B

12.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY