Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0331295 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  Cooling System  


DESCRIPTION

The cause of the malfunction may be the cooling system.

Check whether the grille is blocked, whether coolant is leaking, the radiator fan operating condition and whether coolant has frozen.

Related Parts Check
Area Inspection
Grille blockage, coolant amount, coolant hoses, radiator fan Check for overheating due to hybrid cooling system malfunction.
Inverter coolant temperature sensor (built-in inverter) Check for temperature sensor malfunction.
Coolant freezing check Check freeze frame values to determine whether the hybrid coolant was frozen when the DTC was stored.

Related Data List
Data List
·

Inverter Coolant Water Temperature

·

Motor Inverter Temperature

·

Generator Inverter Calculated Temperature

·

Boosting Converter Temperature (Upper)

·

Boosting Converter Temperature (Lower)

·

Ambient Temperature

·

Inverter Water Pump Revolution



SYSTEM DESCRIPTION

The inverter converts the high-voltage direct current of the HV battery into alternating current for the generator (MG1) and motor (MG2). The inverter generates heat during the conversion process. Therefore, the inverter is cooled by a special cooling system consisting of the inverter water pump assembly, the cooling fan, and a radiator. This cooling system is independent of the engine cooling system. The hybrid vehicle control ECU assembly monitors the inverter water pump assembly, cooling fan and cooling system, and detects malfunctions.

A407880C02
6,1.083 6.25,0.667 6.25,0.667 6.417,0.667 true 3.781,0.76 3.531,0.344 3.531,0.344 3.365,0.344 true 6,3.25 6.167,3.833 6.167,3.833 6.333,3.833 true 4.667,3.5 4.833,4.083 4.833,4.083 5,4.083 true 2.333,3.75 3.25,3.5 3.25,3.5 3.417,3.5 true 3.479,3.438 3.792,3.594 0.313,0.156 10 false *1 3.177,0.292 3.49,0.448 0.313,0.156 10 false *2 6.479,0.625 6.792,0.781 0.313,0.156 10 false *3 5.031,4.031 5.344,4.188 0.313,0.156 10 false *4 6.375,3.781 6.688,3.938 0.313,0.156 10 false *5
*1 Inverter Water Pump Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly *4 Radiator Assembly (HV)
*5 Hybrid Vehicle Transaxle Assembly - -


WIRING DIAGRAM

A368421E13
5.365,5.604 7.073,6.365 1.708,0.76 10 false Hybrid Vehicle Control ECU Assembly 5.781,5.115 6.094,5.313 0.313,0.198 10 false E1 5.792,4.5 6.354,4.74 0.563,0.24 10 false MREL 5.781,3 6.344,3.24 0.563,0.24 10 false NIWP 5.781,1.5 6.344,1.74 0.563,0.24 10 false IWP 6.531,2.615 6.854,2.885 0.323,0.271 10 false +B 6.563,3.896 6.885,4.167 0.323,0.271 10 false +B 5.427,5.104 5.74,5.302 0.313,0.198 10 false K69 5.51,4.885 5.823,5.083 0.313,0.198 10 false 6 2.896,4.063 3.208,4.26 0.313,0.198 10 false w1 5.5,4.385 5.813,4.583 0.313,0.198 10 false 6 5.417,3.104 5.729,3.302 0.313,0.198 10 false A28 5.427,1.604 5.74,1.802 0.313,0.198 10 false A28 5.458,2.896 5.771,3.094 0.313,0.198 10 false 14 5.448,1.396 5.76,1.594 0.313,0.198 10 false 13 5.073,3.615 5.385,3.813 0.313,0.198 10 false 1 4.667,3.76 5.115,4.01 0.448,0.25 10 false GND 4.646,3.01 5.208,3.25 0.563,0.24 10 false NWP 5.073,3.01 5.385,3.208 0.313,0.198 10 false 2 4.646,1.51 5.208,1.75 0.563,0.24 10 false SWP 5.083,1.5 5.396,1.698 0.313,0.198 10 false 3 3.177,2.135 4.104,2.479 0.927,0.344 10 false Drive Circuit 2.729,1.177 3.292,1.417 0.563,0.24 10 false +BWP 2.542,1.198 2.854,1.396 0.313,0.198 10 false 4 2.198,1.146 2.51,1.344 0.313,0.198 10 false 2 1.885,1.146 2.198,1.344 0.313,0.198 10 false 1 1.052,2.021 1.583,2.354 0.531,0.333 10 false IGCT 1.76,1.438 2.688,1.781 0.927,0.344 10 false INV W/PMP 1.573,1.573 1.885,1.771 0.313,0.198 10 false 1 0.802,1.552 1.115,1.75 0.313,0.198 10 false 2 0.792,1.146 1.104,1.344 0.313,0.198 10 false 3 1.583,1.135 1.896,1.333 0.313,0.198 10 false 5 0.458,2.979 1.354,3.313 0.896,0.333 10 false IGCT 0.115,4.958 1.75,5.448 1.635,0.49 10 false from Auxiliary Battery 0.354,5.708 3.427,6.073 3.073,0.365 10 false IWP: Inverter water pump assembly drive duty 0.333,6.031 3.406,6.396 3.073,0.365 10 false NIWP: Inverter water pump assembly speed signal 2.885,4.229 5.042,4.656 2.156,0.427 10 false Inverter Water Pump Assembly 5.427,4.604 5.74,4.802 0.313,0.198 10 false A29

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Make sure that the front side of the radiator grille is not blocked with anything.


b.

Ask the customer if the front side of the radiator grille was blocked with anything.


Result:
Result Proceed to
Not blocked. A
Is/was blocked. B


HINT:

If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.



A

2.CHECK QUANTITY OF HV COOLANT

B

IF EQUIPPED, EXPLAIN TO CUSTOMER THAT OPTIONAL COMPONENTS WILL BE REMOVED

2.CHECK QUANTITY OF HV COOLANT
a.

Check the HV coolant level in the inverter reserve tank.


b.

Check for HV coolant leaks.

Result:
Result Proceed to
No leaks are found and the HV coolant level in the inverter reserve tank assembly is above the low line. A
No leaks are found and the HV coolant level in the inverter reserve tank assembly is below the low line. B
HV coolant leaks are evident. C


HINT:
·

After repairing the HV coolant leaks and adding coolant, perform the Active Tests "Activate the Inverter Water Pump" (Hybrid Control System) and "Control the Cooling Fan Duty Ratio" (Engine Control system) and make sure that there are no malfunctions.

·

If there are signs of coolant leakage around the connecting parts of a hose and the inverter with converter assembly, replace the hose with a new one.





A

3.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR COOLANT LEAK AND ADD COOLANT

3.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)

NG

REPAIR OR REPLACE COOLANT HOSE

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11

d.

Perform the "Control the Engine Cooling Fan Duty Ratio" Active Test.

OK:
GTS Operation Fan Operation
30 - 100% Cooling fan operates
0% Cooling fan stops



Result:
Result Proceed to
Cooling fan operate (w/ Grill Shutter System) A
Cooling fan operate (w/o Grill Shutter System) B
Cooling fan does not operate C
Cooling fan do not stop


e.

Turn the power switch off.



A

5.CHECK GRILLE SHUTTER SYSTEM

B

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)

C

5.CHECK GRILLE SHUTTER SYSTEM
a.

Check the Grill Shutter System.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

OK:

The Grill Shutter System is normal.



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)

NG

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.



HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.

Powertrain > Hybrid Control > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump Revolution
50004 397 1 60

d.

Select the Data List item "Inverter Water Pump Revolution".


e.

According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and check the value of the Data List item "Inverter Water Pump Revolution".

OK:
Tester Display Condition Specified Condition
Inverter Water Pump Revolution Power switch on (IG)
During Active Test
3176 to 8617 rpm


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.




f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (DATA LIST)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)
7.READ VALUE USING GTS (DATA LIST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY) and wait for 1 minute with the engine stopped.


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator Inverter Calculated Temperature, Motor Inverter Temperature, Boosting Converter Temperature (Upper), Boosting Converter Temperature (Lower) and Inverter Coolant Water Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Inverter Calculated Temperature
Motor Inverter Temperature
Boosting Converter Temperature (Upper)
Boosting Converter Temperature (Lower)
Inverter Coolant Water Temperature
50003 397 127,130,136,137,152

d.

Read the Data List with the engine stopped.

Result:
Result Proceed to
Other than below. A
"Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (68°F) or more. B


HINT:

The lower limit temperature that can be displayed for "Generator Inverter Calculated Temperature", "Motor Inverter Temperature", "Boosting Converter Temperature (Upper)" and "Boosting Converter Temperature (Lower)" is 15°C (59°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the GTS may be lower than the others, but this is not a malfunction.



e.

Turn the power switch off.



A

8.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

8.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Read the freeze frame data item "Ambient Temperature" using the GTS.


e.

Check if the freeze frame data item "Ambient Temperature" is below the freezing temperature of the HV coolant.

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the HV coolant. A
Ambient Temperature value is below freezing temperature of the HV coolant. B


HINT:
·

HV coolant (SLLC) with a 30% concentration freezes at -15°C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the HV coolant freezes in the HV radiator or inverter water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be stored.

·

A DTC is stored when the inverter water pump impeller cannot rotate due to freezing of the HV coolant.

·

If DTCs are output due to freezing of the LLC, the problem symptom cannot be reproduced. Check the LLC replacement history and whether the LLC was frozen based on the ambient temperature when the DTCs were stored.




f.

Turn the power switch off.



A

COOLING SYSTEM NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

B

9.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

OK

10.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

10.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
a.
A407566

Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely, the terminals are not deformed or corroded and there are no contact problems.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A28 hybrid vehicle control ECU assembly connector.


b.

Disconnect the w1 inverter water pump assembly connector.


c.
A406706C06
0.542,0.26 0.99,0.531 0.448,0.271 0.375,3.313 0.823,3.583 0.448,0.271 2.073,4.031 1.823,3.521 true 1.375,2.375 0.771,2.104 true 0.073,0.115 0.385,0.313 0.313,0.198 10 false *a 0.094,2.885 0.406,3.083 0.313,0.198 10 false *b 0.635,0.323 0.948,0.521 0.313,0.198 10 false A28 0.521,3.375 0.833,3.573 0.313,0.198 10 false w1 1.927,4.083 2.448,4.292 0.521,0.208 10 false SWP 1.448,2.365 1.969,2.573 0.521,0.208 10 false IWP
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A28-13 (IWP) - w1-3 (SWP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A28-13 (IWP) or w1-3 (SWP) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Reconnect the w1 inverter water pump assembly connector.


e.

Reconnect the A28 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.
A405854C01
2.271,2.177 2.76,1.792 true 0.448,0.219 0.76,0.417 0.313,0.198 10 false *1 2.865,1.708 3.177,1.906 0.313,0.198 10 false *2
*1 No. 4 Relay Block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from the No. 4 relay block.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Water Pump Revolution.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60

e.

According to the display on the GTS, read the Data List.

Standard:
GTS Display Condition Specified Condition
Inverter Water Pump Revolution Power switch on (IG) 200 rpm or less



f.

Turn the power switch off.


g.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WATER PUMP ASSEMBLY)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A28 hybrid vehicle control ECU assembly connector.


b.

Turn the power switch on (IG).


c.
A389501C14
1.781,0.656 2.281,0.906 0.5,0.25 0.552,0.667 1.052,0.917 0.5,0.25 0.417,2.917 0.781,2.448 true 1.823,1.385 1.656,2.167 true 0.115,0.219 0.427,0.375 0.313,0.156 10 false *a 0.104,1.99 0.417,2.146 0.313,0.156 10 false *b 1.521,2.188 1.833,2.344 0.313,0.156 10 false E1 0.292,2.958 0.771,3.115 0.479,0.156 10 false IWP 0.677,0.708 0.99,0.865 0.313,0.156 10 false A28 1.906,0.708 2.219,0.865 0.313,0.156 10 false K69
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-13 (IWP) - K69-6 (E1) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the A28 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

14.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK WAVEFORM)

NG

15.REPLACE INVERTER WATER PUMP ASSEMBLY
14.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU assembly terminals specified in the table below.


b.

Turn the power switch on (IG).


c.
A389500C83
0.594,1 0.969,1.229 0.375,0.229 1.865,1 2.24,1.25 0.375,0.25 0.583,2.417 0.781,1.781 true 1.667,2.417 1.813,1.708 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,2.448 1.896,2.604 0.313,0.156 10 false E1 0.479,2.479 1.042,2.646 0.563,0.167 10 false IWP 0.667,1.052 1.24,1.385 0.573,0.333 10 false A28 1.948,1.063 2.375,1.427 0.427,0.365 10 false K69
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


While turning the power switch on (IG), check the waveform between the hybrid vehicle control ECU assembly terminals.

Item Content
Terminal A28-13 (IWP) - K69-6 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Power switch on (IG)

OK:

Waveform duty ratio is between 3% and 9%.



d.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

15.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

15.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

16.ADD HV COOLANT AND PERFORM AIR BLEEDING
16.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COOLANT(for Inverter)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END