When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift Position.
| Tester Display |
|---|
| Sports Shift Position |
Read the value displayed on the GTS.
| Result | Proceed to |
|---|---|
| The GTS display changes according to the shift lever operation | A |
| The GTS display does not change according to the shift lever operation | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift UP Signal, Sports Shift DOWN Signal.
| Tester Display |
|---|
| Sports Shift UP Signal |
| Sports Shift DOWN Signal |
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Sports Shift UP Signal | Operation of "+" transmission control switch. | ON or OFF | Shift lever held in "+" operated: ON
Shift lever in S: OFF |
| Sports Shift DOWN Signal | Operation of "-" transmission control switch. | ON or OFF | Shift lever held in "-" operated: ON
Shift lever in S: OFF |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the transmission control switch (shift lock control unit assembly) operation | A |
| The GTS display does not change according to the transmission control switch (shift lock control unit assembly) operation | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.
Turn the power switch on (IG).
| *a | Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-4 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-4 (IG) - Body ground | Power switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-2 (E) - Body ground | Power switch off | Below 1 Ω |
Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-4 (IG) - K29-5 (S) | Shift lever in S
Shift lever held in "+" or "-" |
Below 13 Ω |
| K29-4 (IG) - K29-5 (S) | Shift lever in any position except S | 10 kΩ or higher |
| K29-3 (SFTU) - K29-2 (E) | Shift lever held in "+" | Below 13 Ω |
| K29-3 (SFTU) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
| K29-1 (SFTD) - K29-2 (E) | Shift lever held in "-" | Below 13 Ω |
| K29-1 (SFTD) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-4 (IG) - K29-5 (S) | Shift lever in S
Shift lever held in "+" or "-" |
Below 13 Ω |
| K29-4 (IG) - K29-5 (S) | Shift lever in any position except S | 10 kΩ or higher |
| K29-1 (SFTU) - K29-2 (E) | Shift lever held in "+" | Below 13 Ω |
| K29-1 (SFTU) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
| K29-3 (SFTD) - K29-2 (E) | Shift lever held in "-" | Below 13 Ω |
| K29-3 (SFTD) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Disconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-1 (M) - Body ground | Power switch on (IG)
Shift lever in S, "+" or "-" |
11 to 14 V |
| Power switch on (IG)
Except shift lever in S, "+" and "-" |
Below 1 V |
If the power switch is turned on (IG) with the hybrid vehicle control ECU assembly connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.
Turn the power switch off.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-9 (SFTU) - Body ground | Shift lever held in "+" | Below 13 Ω |
| K70-9 (SFTU) - Body ground | Shift lever in S | 10 kΩ or higher |
| K70-8 (SFTD) - Body ground | Shift lever held in "-" | Below 13 Ω |
| K70-8 (SFTD) - Body ground | Shift lever in S | 10 kΩ or higher |
Reconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K29 transmission control switch (shift lock control unit assembly) connector.
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(to Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-3 (SFTU) - K29-2 (E) | Shift lever held in "+" | Below 13 Ω |
| K29-3 (SFTU) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
| K29-1 (SFTD) - K29-2 (E) | Shift lever held in "-" | Below 13 Ω |
| K29-1 (SFTD) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-1 (SFTU) - K29-2 (E) | Shift lever held in "+" | Below 13 Ω |
| K29-1 (SFTU) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
| K29-3 (SFTD) - K29-2 (E) | Shift lever held in "-" | Below 13 Ω |
| K29-3 (SFTD) - K29-2 (E) | Shift lever in S | 10 kΩ or higher |
Reconnect the K29 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K70 hybrid vehicle control ECU assembly connector.
Disconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K70-9 (SFTU) - Body ground | Shift lever held in "+" | Below 13 Ω |
| Shift lever in S | 10 kΩ or higher | |
| K70-8 (SFTD) - Body ground | Shift lever held in "-" | Below 13 Ω |
| Shift lever in S | 10 kΩ or higher |
Reconnect the K22 spiral cable sub-assembly connector. (w/ Shift paddle switch)
Reconnect the K70 hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG