CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-3 - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 3C-1 - Body ground | LG - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| 3F-1 - Body ground | W - Body ground | Auxiliary battery power supply | Power switch off | 11 to 14 V |
Connect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3C-19 - Body ground | BE - Body ground | BKUP LP relay drive output | Power switch off, shift lever not in R | Below 1 V |
| Power switch on (IG), shift lever in R | 11 to 14 V | |||
| 3C-25 - Body ground* | BE - Body ground | FOG FR relay drive output | Light control switch in tail or head position, fog light switch in front position | Below 1 V |
| Light control switch in tail or head position, fog light switch off position | 11 to 14 V | |||
| 3C-28 - Body ground | GR - Body ground | Daytime running light system drive output | Daytime running light system operating | Below 1 V |
| Daytime running light system not operating | 11 to 14 V | |||
| 3C-31 - Body ground | V - Body ground | H-LP LH relay drive output | Light control switch in head position | Below 1 V |
| Taillights off | 11 to 14 V | |||
| 3C-32 - Body ground | LA-B - Body ground | Clearance lights drive output | Taillights on | 11 to 14 V |
| Taillights off | Below 1 V | |||
| 3D-10 - Body ground | LG - Body ground | Back-up lights drive output | Power switch off, shift lever not in R | Below 1 V |
| Power switch on (IG), shift lever in R | 11 to 14 V | |||
| 3D-21 - Body ground | LG - Body ground | Rear fog light drive output | Light control switch in tail or head position, fog light switch in rear position | 11 to 14 V |
| Light control switch in tail or head position, fog light switch off position | Below 1 V | |||
| 3D-30 - Body ground | LA-B - Body ground | Taillights and license plate lights drive output | Taillights on | 11 to 14 V |
| Taillights off | Below 1 V | |||
| K51-14 (LLEW) - Body ground | GR - Body ground | Light control ECU signal input | Power switch on (IG), taillights off | 11 to 14 V |
| Power switch on (IG), light control switch in head position | Pulse generation | |||
| K51-15 (RLEW) - Body ground | R - Body ground | Light control ECU signal input | Power switch on (IG), taillights off | 11 to 14 V |
| Power switch on (IG), light control switch in head position | Pulse generation | |||
| K51-19 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| K52-12 (HRY2) - Body ground | BE - Body ground | H-LP RH relay drive output | Light control switch in head position | Below 1 V |
| Taillights off | 11 to 14 V | |||
| K52-13 (DIM) - Body ground | G - Body ground | High beam headlight drive output | Light control switch in head position and dimmer switch in high or high flash position | Below 1 V |
| Dimmer switch not in high or high flash position | 11 to 14 V | |||
| K52-16 (HEAD) - Body ground | LG - Body ground | Light control switch head position input | Light control switch in head position | Below 1 V |
| Light control switch not in head position | 11 to 14 V | |||
| K52-23 (CLTB) - K52-25 (CLTE) | BE - GR | Automatic light control sensor power supply output | Power switch off | Below 1 V |
| Power switch on (IG) | 11 to 14 V | |||
| K52-24 (CLTS) - Body ground | R - Body ground | Automatic light control sensor signal input | Power switch off | Below 1 V |
| Power switch on (IG) | Pulse generation
(See waveform 1) |
*: w/ Front Fog Light
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | K52-24 (CLTS) - Body ground |
| Tool setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Power switch on (IG) |
The communication waveform changes according to the surrounding brightness.
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
CHECK STEERING SENSOR
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
for NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
for LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>TERMINALS OF ECU