Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
89305
1.INSTALL ULTRASONIC SENSOR CUSHION SET
Only perform this procedure when removing and installing the ultrasonic sensor cushion set.
Install the ultrasonic sensor cushion set as shown in the illustration.
|
Install in this Direction | - | - |
89347B
2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/o Parking Support Brake System)
Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.
If a front corner ultrasonic sensor retainer has been removed, replace it with a new one. Install the front corner ultrasonic sensor with a new front corner ultrasonic sensor retainer as a set to the front bumper assembly.
Engage the 2 claws to install a new front corner ultrasonic sensor retainer to the front corner ultrasonic sensor.
Clean the surface of the front bumper assembly.
Remove any remaining double-sided tape from the front bumper assembly.
Wipe off any adhesive residue with cleaner.
| *a | 19 mm (0.748 in.) |
Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.
for Bar Type Radiator Grille:
|
Primer |
Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.
Use a clean brush or felt.
Do not touch the front bumper assembly until the primer has dried.
Mesh Type Radiator Grille:
|
Primer |
Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.
Use a clean brush or felt.
Do not touch the front bumper assembly until the primer has dried.
Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.
Peel off the release paper from the front corner ultrasonic sensor retainer.
for Bar Type Radiator Grille:
| *a | Scribed Line |
|
Press Here |
Align the front corner ultrasonic sensor retainer with front corner ultrasonic sensor with the mark on the front bumper assembly and install it as shown in the illustration.
Ensure that the sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.
Ensure that the front corner ultrasonic sensor retainer is within the scribed line.
The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.
Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.
Mesh Type Radiator Grille:
| *a | Scribed Line |
|
Press Here |
Align the front corner ultrasonic sensor retainer with front corner ultrasonic sensor with the mark on the front bumper assembly and install it as shown in the illustration.
Ensure that the sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.
Ensure that the front corner ultrasonic sensor retainer is within the scribed line.
The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.
Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.
89348J
3.INSTALL ULTRASONIC SENSOR CLIP (w/o Parking Support Brake System)
Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
for Bar Type Radiator Grille:
Engage the clamp to install the ultrasonic sensor clip to the wire.
89341K
4.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/o Parking Support Brake System)
for Bar Type Radiator Grille:
|
Install in this Direction |
When replacing only the front corner ultrasonic sensor:
Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.
|
Install in this Direction |
Engage the claw as shown in the illustration.
Connect the connector.
for Mesh Type Radiator Grille:
|
Install in this Direction |
When replacing only the front corner ultrasonic sensor:
Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.
Connect the connector.
89347B
5.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.
If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.
Clean the surface of the front bumper assembly.
Remove any remaining double-sided tape from the front bumper assembly.
Wipe off any adhesive residue with cleaner.
| *a | 25 mm (0.984 in.) |
Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.
Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.
| *A | for LH Side | *B | for RH Side |
|
Primer | - | - |
Use a clean brush or felt.
Do not touch the front bumper assembly until the primer has dried.
Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.
Peel off the release paper from a new front corner ultrasonic sensor retainer.
Align the front corner ultrasonic sensor retainer with the mark on the front bumper assembly and install it as shown in the illustration.
| *A | for LH Side | *B | for RH Side |
| *a | Scribed Line | - | - |
|
Press Here | - | - |
Ensure that the front corner ultrasonic sensor retainer is within the scribed line.
The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.
Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.
89348J
6.INSTALL ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)
Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
Engage the clamp to install the ultrasonic sensor clip to the wire.
89341K
7.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)
|
Install in this Direction |
Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.
|
Install in this Direction |
Engage the 4 claws as shown in the illustration.
Connect the connector.
89341L
8.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)
|
Install in this Direction |
Engage the 2 claws to install the front center ultrasonic sensor as shown in the illustration.
Connect the connector.
9.INSTALL FRONT BUMPER ASSEMBLY
10.PERFORM CALIBRATION (w/o Parking Support Brake System)
11.PERFORM CALIBRATION (w/ Parking Support Brake System)
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION