The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.REMOVE REAR BUMPER ASSEMBLY
89342
2.REMOVE REAR CORNER ULTRASONIC SENSOR (w/o Parking Support Brake System)
|
Remove in this Direction |
Disconnect the connector.
Disengage the claw as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.
89348J
3.REMOVE ULTRASONIC SENSOR CLIP (w/o Parking Support Brake System)
Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
Disengage the clamp to remove the ultrasonic sensor clip from the wire.
89348R
4.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/o Parking Support Brake System)
Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.
When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.
Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Rear Corner Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the rear corner ultrasonic sensor retainer.
89342A
5.REMOVE REAR CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)
|
Remove in this Direction |
Disconnect the connector.
Disengage the 4 claws as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.
89342
6.REMOVE REAR CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)
|
Remove in this Direction |
Disconnect the connector.
Disengage the 4 claws as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.
89348J
7.REMOVE ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)
Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
Use the same procedure for all ultrasonic sensor clips.
Disengage the clamp to remove the ultrasonic sensor clip from the wire.
89348S
8.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.
When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.
Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Rear Center Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the rear center ultrasonic sensor retainer.
89348R
9.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.
When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.
Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Rear Corner Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Remove the rear corner ultrasonic sensor retainer.
89305
10.REMOVE ULTRASONIC SENSOR CUSHION SET
Only perform this procedure when removing and installing the ultrasonic sensor cushion set.
Remove the ultrasonic sensor cushion set as shown in the illustration.
|
Remove in this Direction | - | - |