Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2021.02
RM33C0E _58 Vehicle Interior _065464 HEATING / AIR CONDITIONING _0329891 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Operation not Accepted Even If Air Conditioning Switch is Operated  


DESCRIPTION

If the air conditioning system cannot be operated using the air conditioning control assembly, the following factors may be the cause.

Symptom Factor
Air conditioning system cannot be operated using air conditioning control assembly

(With the exception of the switch indicators, no inputs are reflected when other switches operated)


·

LIN communication malfunction between air conditioning amplifier assembly and air conditioning control assembly

·

Short to +B or ground in air conditioning amplifier assembly circuit

·

Air conditioning amplifier assembly malfunction

·

Air conditioning control assembly malfunction

·

Harness or connector



WIRING DIAGRAM

E375276E01
2.052,0.604 3.469,0.833 1.417,0.229 10 false from Auxiliary Battery 2.052,1.115 3.469,1.344 1.417,0.229 10 false from IG1-NO. 1 Relay 3.979,0.75 4.885,0.958 0.906,0.208 10 false ECU-B NO. 2 3.927,1.271 4.99,1.479 1.063,0.208 10 false ECU-IG1 NO. 4 5.26,0.625 5.51,0.792 0.25,0.167 10 false B 5.26,1.667 5.667,1.865 0.406,0.198 10 false LIN1 1.646,1.667 2.052,1.865 0.406,0.198 10 false LIN1 5.25,1.125 5.656,1.323 0.406,0.198 10 false IG+ 5.26,2.385 5.667,2.583 0.406,0.198 10 false GND 5.063,0.49 5.313,0.656 0.25,0.167 10 false 1 5.01,1.5 5.271,1.677 0.26,0.177 10 false 14 5.063,1.01 5.323,1.188 0.26,0.177 10 false 2 5.083,2.26 5.344,2.438 0.26,0.177 10 false 4 2.021,1.51 2.281,1.688 0.26,0.177 10 false 9 0.583,2.906 2.781,3.115 2.198,0.208 10 false Air Conditioning Control Assembly 0.583,2.729 0.99,2.927 0.406,0.198 10 false K26 4.927,2.771 5.333,2.969 0.406,0.198 10 false K54 4.917,2.948 7.115,3.156 2.198,0.208 10 false Air Conditioning Amplifier Assembly 0.948,3.396 2.771,3.615 1.823,0.219 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
B14B2 is not output A
B14B2 is output B



A

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - POWER SOURCE AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - POWER SOURCE AND BODY GROUND)
E328994C12
1.531,0.448 1.917,0.698 0.385,0.25 2.573,1.958 2.75,1.229 2.75,1.229 2.917,1.229 true 0.802,1.979 0.531,1.552 0.531,1.552 0.323,1.552 true 1.021,1.958 0.667,1.302 0.667,1.302 0.458,1.302 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.604,0.479 1.927,0.656 0.323,0.177 10 false K54 2.969,1.135 3.344,1.333 0.375,0.198 10 false GND 0.208,1.208 0.521,1.385 0.313,0.177 10 false IG+ 0.198,1.458 0.354,1.625 0.156,0.167 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K54-1 (B) - Body ground Power switch off 11 to 14 V
K54-2 (IG+) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
K54-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR