Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA › from 2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0331761 FRONT CAMERA A

CRUISE CONTROL  FRONT CAMERA  DRIVING ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:
·

Make sure to read "Before Starting Driving Adjustment" before proceeding with work.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>BEFORE STARTING DRIVING ADJUSTMENT

·

Make sure to perform the transition to online axis alignment mode with the vehicle stopped.

·

Transitioning to online axis alignment mode will erase the learning value, so make sure to complete the adjustment.

·

Turning the power switch off while in online axis alignment mode will cause the system to exit online axis alignment mode, so to continue with the adjustment, it is necessary to transition to online axis alignment mode again.

·

All of the driving support system functions will be inoperative while the adjustment is in progress.

·

When driving the vehicle with the GTS connected, be careful with how the wires are routed.

·

If the adjustment does not complete within a total cumulative time of 15 minutes when the vehicle is driven with all conditions met, perform the adjustment on another route.

·

If the adjustment does not complete within a total cumulative time of 30 minutes when the vehicle is driven with all conditions met, perform the adjustment using target recognition.

·

After adjustment is complete, to start the various systems it is necessary to turn the power switch off and then to on (IG) again.

·

In situations such as when the online axis alignment terminates abnormally, to perform online axis alignment again, turn the power switch off and then back to on (IG) and enter online axis alignment mode again.

·

For vehicles with height adjustment function, perform the adjustment at the standard vehicle height.



PROCEDURE

Hide 1. PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING (When driving with GTS connected to vehicle)

NOTICE:
·

Perform this procedure with the vehicle unloaded (without the emergency tire puncture repair kit or tools).

·

Only 1 person should be in the vehicle.



a.

Adjust the tire pressures to the standard values.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Clean the windshield glass.


c.

If the windshield glass in front of the forward recognition camera is fogged up, remove the forward recognition camera and forward recognition hood, clear the condensation, and then reinstall the forward recognition camera and forward recognition hood.

Forward recognition hood removal: Click hereEngine / Hybrid System>CRUISE CONTROL>CAMERA HEATER>REMOVAL

Forward recognition hood installation: Click hereEngine / Hybrid System>CRUISE CONTROL>CAMERA HEATER>INSTALLATION


d.

Check that RoB/DTCs other than "X2014 Front Recognition Camera Optical Axis Not Adjusted" are not output.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


e.

Transition to online axis alignment mode.

i.

With the power switch off, connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Enter the following menus: Chassis / Front Recognition Camera / Utility / Transition to Online Axis Alignment Mode

Chassis > Front Recognition Camera > Utility
Tester Display
Transition to Online Axis Alignment Mode
50005 430 2633

iv.

Confirm the conditions displayed on the screen and then press "Next".


v.

Select "Front recognition camera" and then press "Next".


vi.

Check the GTS screen and confirm that it has transitioned to online axis alignment mode.


vii.

Press "Next".



f.

Online axis adjustment (Optical Axis Learning)

i.

Drive the vehicle to perform optical axis learning.

HINT:

If the alignment is performed with the GTS connected to the vehicle, the alignment progress can be monitored through 5 stages on the GTS screen.



ii.

If the online axis alignment completes normally, the buzzer will sound 5 times.

NOTICE:
·

If the alignment terminates abnormally, the buzzer will sound for 3 seconds continuously.

·

If an error code is displayed, perform troubleshooting according to the following table, then perform the optical axis alignment again.

Error No. Error Description Cause of Error Action to be Taken
31 Exceeded vehicle speed precondition for start of online axis alignment
·

Excessive vehicle speed at the start of online axis alignment


·

Ensure that the vehicle is stopped (vehicle speed 0 km/h) when starting online axis alignment.


32 Camera dirty during online axis alignment
·

During online axis alignment, dirtiness of the camera interferes with the axis adjustment.


·

Check that front of camera is not covered.

·

Check that front of camera is not dirty.

·

Check that front of camera is not fogged.

·

Check that weather is not bad (rain/fog).

·

Check that camera view is not backlit or high-glare.


33 Recognition invalid during online axis alignment
·

DTC/RoB is stored during online axis alignment.


·

Check whether DTC/RoB is stored.


34 Online axis alignment FOE out-of-range
·

FOE result from online axis alignment is offset from standard value.


·

Check camera installation condition. (Check if camera is not seated correctly)

·

Check whether tire inflation pressure is correct.


35 Online axis alignment FOE write error
·

FOE result from online axis alignment cannot be written to camera.


·

Inspect front camera.






iii.

Press "Exit" to exit the Online axis adjustment mode.


iv.

Turn the power switch off.


v.

Turn the power switch on (IG) and check that the warning light turns off.


vi.

Turn the power switch off.


vii.

Disconnect the GTS from the DLC3.



g.

Forward recognition camera optical axis learning is complete.


h.

After beam axis adjustment completes, clear the following system vehicle control history entries.

i.

Clear vehicle control history (Dynamic Radar Cruise Control System).

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY


ii.

Clear vehicle control history (Front Camera System).

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>VEHICLE CONTROL HISTORY


iii.

Clear vehicle control history (Lane Tracing Assist System).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY


iv.

Clear vehicle control history (Road Sign Assist System).

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY


v.

Clear vehicle control history (Pre-collision System).

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY




Hide 2. PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING (When driving with GTS not connected to vehicle)

NOTICE:
·

Perform this procedure with the vehicle unloaded (without the emergency tire puncture repair kit or tools).

·

Only 1 person should be in the vehicle.



a.

Adjust the tire pressures to the standard values.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Clean the windshield glass.


c.

If the windshield glass in front of the forward recognition camera is fogged up, remove the forward recognition camera and forward recognition hood, clear the condensation, and then reinstall the forward recognition camera and forward recognition hood.

Forward recognition hood removal: Click hereEngine / Hybrid System>CRUISE CONTROL>CAMERA HEATER>REMOVAL

Forward recognition hood installation: Click hereEngine / Hybrid System>CRUISE CONTROL>CAMERA HEATER>INSTALLATION


d.

Check that RoB/DTCs other than "X2014 Front Recognition Camera Optical Axis Not Adjusted" are not output.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


e.

Transition to online axis alignment mode.

i.

With the power switch off, connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Enter the following menus: Chassis / Front Recognition Camera / Utility / Transition to Online Axis Alignment Mode

Chassis > Front Recognition Camera > Utility
Tester Display
Transition to Online Axis Alignment Mode
50005 430 2633

iv.

Confirm the conditions displayed on the screen and then press "Next".


v.

Select "Front recognition camera" and then press "Next".


vi.

Check the GTS screen and confirm that it has transitioned to online axis alignment mode.


vii.

Press "Next".


viii.

In accordance with the instructions on the screen press "Exit" and then disconnect the GTS from the DLC3.



f.

Online axis adjustment (Optical Axis Learning)

i.

Drive the vehicle to perform optical axis learning.


ii.

If the online axis alignment completes normally, the buzzer will sound 5 times.

NOTICE:

If the alignment terminates abnormally, the buzzer will sound for 3 seconds continuously.



iii.

Turn the power switch off.


iv.

Turn the power switch on (IG) and check that the warning light turns off.


v.

Turn the power switch off.



g.

Forward recognition camera optical axis learning is complete.


h.

After beam axis adjustment completes, clear the following system vehicle control history entries.

i.

Clear vehicle control history (Dynamic Radar Cruise Control System).

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY


ii.

Clear vehicle control history (Front Camera System).

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>VEHICLE CONTROL HISTORY


iii.

Clear vehicle control history (Lane Tracing Assist System).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY


iv.

Clear vehicle control history (Road Sign Assist System).

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY


v.

Clear vehicle control history (Pre-collision System).

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY