Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2021.02
RM33C0E _59 Vehicle Exterior _065474 EXTERIOR PANELS / TRIM _0328281 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Applies only for when removing and installing or replacing the rear television camera assembly.

Front bumper assembly (w/ Parking Support Brake System)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front bumper assembly (w/ Panoramic View Monitor System) Front television camera view adjustment Panoramic View Monitor System (Click here)for Initialization
(Click here)for Calibration
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, front bumper assembly or radiator grille

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


·

Television camera view adjustment

·

Rear television camera assembly optical axis (Back camera position setting)*



HINT:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

TARGET ADJUSTMENT(TRIANGLE TARGET):

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

TARGET ADJUSTMENT(FLAT SURFACE TARGET):

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

DRIVING ADJUSTMENT:

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


PROCEDURE

Hide 53295E 1.REMOVE COOL AIR INTAKE DUCT SEAL

a.
B596540

Remove the 5 clips.


b.
B596541C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the guide and remove the cool air intake duct seal as shown in the illustration.


Hide 2.REMOVE FRONT BUMPER ASSEMBLY

a.
B607458C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front bumper assembly as shown in the illustration.


b.
B610750C02
1.073,1.74 1,1.583 true 1,1.74 1.198,1.938 0.198,0.198 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



c.
B470347

Remove the clip.

HINT:

Use the same procedure for the RH side and LH side.



d.
B607459

Remove the 8 screws.


e.
B607460C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



f.

w/ Pre-collision System:

i.
B607462

Disconnect the connector.



g.

w/ TOYOTA Parking Assist-sensor System:

i.
B607463

Disconnect the connector.



h.
B607464

Remove the 2 clips.


i.

Remove the 4 bolts.


j.
B607465C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides to remove the front bumper assembly as shown in the illustration.


k.

w/ Fog Light:

i.

Disconnect the connector.



l.

w/ Headlight Cleaner System:

i.
B490252

Disconnect the headlight cleaner hose and drain the washer fluid.

HINT:

Use a container to collect the washer fluid.