Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0468732 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  CALIBRATION  


ADJUST PANORAMIC VIEW MONITOR SYSTEM


a.

This panoramic view monitor system can be set from the diagnostic screen of the radio and display receiver assembly.


b.

If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

Part Name Operation Adjustment Item Proceed to

*: When "!" is displayed on the panoramic view monitor screen, perform steering sensor zero point calibration.

Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize panoramic view monitor system)* (Click here)
Adjust steering angle Procedure 9
Television camera controller Replacement Television camera controller initialization Procedure 2
Procedure 7
Procedure 8
Adjust steering angle Procedure 9
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Television camera controller initialization Procedure 2
Procedure 7
Procedure 8
Adjust steering angle Procedure 9
Rear television camera view adjustment (for Rear camera detection function) Procedure 10
Rear television camera assembly
·

Replacement

·

Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.


Rear television camera view adjustment Procedure 2
Procedure 4
Procedure 8
Rear television camera view adjustment (for Rear camera detection function) Procedure 10
·

Front television camera assembly

·

Front bumper assembly

·

Radiator grille sub-assembly


·

Replacement

·

Installation angle of the front television camera changes because of the removal and installation of the front television camera, etc.


Front television camera view adjustment Procedure 2
Procedure 3
Procedure 8
·

Side television camera assembly LH

·

Outer rear view mirror assembly LH


·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 5
Procedure 8
·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 6
Procedure 8
·

Front television camera assembly, front bumper assembly or radiator grille sub-assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Replacement or removal and installation of 2 or more parts Television camera view adjustment Procedure 2
Procedure 7
Procedure 8
Rear television camera view adjustment (for Rear camera detection function) Procedure 10

HINT:

The adjustment values stored while performing panoramic view monitor system calibration are stored in the television camera controller.




PROCEDURE 1: PRE-WORK CHECKS


a.

Preliminary checks

NOTICE:
·

Provide shadow to prevent back-up light from hitting the camera.

·

Use string that does not stretch.

·

Apply pieces of adhesive tape to serve as check markers. When placing the markers, make them 100 mm (3.94 in.) wide.



i.

Perform the work at a wide, level location (There is approximately 2000 mm [6.56 ft.] all around the vehicle).


ii.

Park the vehicle on a flat surface with the steering wheel centered.

NOTICE:

Before stopping the vehicle, move the vehicle backward and forward to ensure that both the steering wheel and the tires point straight ahead.



iii.

Adjust the tire pressure to the specified value(s).


iv.

Remove all luggage from the vehicle before starting work.



b.

Marker locations

i.

Secure the string to the locations required to make the checks and set markers as shown in the illustration.

·
E287135C01
0.479,0.698 0.844,1.146 false 2.229,0.469 1.844,1.115 false 2.302,1.333 2.552,1.708 false 1.104,1.333 0.854,1.74 false 2.01,4.052 1.708,3.688 false 2.573,3.49 2.271,3.083 false 0.292,0.583 0.75,0.781 0.458,0.198 10 false *e 2.302,0.396 3.188,0.677 0.885,0.281 10 false *b 0.729,1.76 0.948,2 0.219,0.24 10 false *a 2.063,4 2.521,4.198 0.458,0.198 10 false *d 2.615,3.5 3.073,3.698 0.458,0.198 10 false *c 2.531,1.75 2.75,1.99 0.219,0.24 10 false *a
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3


Front camera adjustment only

·
E287136C01
1.719,1.042 2.073,0.563 false 2.552,3.135 2.781,2.729 false 2.375,3.823 2.5,4.01 false 0.958,3.823 0.708,4.094 false 1.521,3.813 1.521,4.292 false 0.552,3.49 0.76,3.792 false 2.146,0.469 2.604,0.667 0.458,0.198 10 false *d 0.385,3.406 0.844,3.604 0.458,0.198 10 false *e 0.563,4.094 1.25,4.458 0.688,0.365 10 false *a 2.458,4.042 3.146,4.406 0.688,0.365 10 false *a 1.427,4.344 2.365,4.552 0.938,0.208 10 false *b 2.823,2.635 3.323,2.854 0.5,0.219 10 false *c
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 4


Rear camera adjustment only

·
E287137C01
1.063,0.917 0.688,0.563 false 2.281,0.958 2.688,0.656 false 2.271,2.906 2.625,2.646 false 2.375,3.521 2.688,3.313 false 1.719,3.635 1.927,3.875 false 1.125,3.542 1.49,4.125 false 1.094,3.833 0.844,4.083 false 1.073,1.542 0.771,1.365 false 1.052,2.25 0.781,2.375 false 0.531,0.458 1.24,0.833 0.708,0.375 10 false *a 1.469,4.167 1.698,4.406 0.229,0.24 10 false *a 0.594,1.281 0.969,1.573 0.375,0.292 10 false *b 0.708,4.083 1.156,4.333 0.448,0.25 10 false *g 1.958,3.844 2.406,4.094 0.448,0.25 10 false *d 2.667,2.563 3.115,2.813 0.448,0.25 10 false *c 2.74,3.24 3.188,3.49 0.448,0.25 10 false *f 2.719,0.583 3.167,0.833 0.448,0.25 10 false *e 0.604,2.323 0.979,2.615 0.375,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 5


Left camera adjustment only

·
E287138C01
0.573,0.438 0.854,0.906 false 2.615,0.563 2.344,0.854 false 2.594,3.781 2.313,3.74 false 2.271,3.521 1.844,4.188 false 1.708,3.615 1.365,3.844 false 0.969,3.479 0.75,3.229 false 0.885,2.865 0.667,2.615 false 2.615,1.188 2.344,1.479 false 2.677,2.427 2.344,2.167 false 2.646,0.5 3.344,0.844 0.698,0.344 10 false *a 1.74,4.188 2.104,4.448 0.365,0.26 10 false *a 2.635,1.094 2.979,1.385 0.344,0.292 10 false *b 0.406,0.323 0.792,0.542 0.385,0.219 10 false *e 0.51,2.49 0.896,2.708 0.385,0.219 10 false *c 0.594,3.125 0.979,3.344 0.385,0.219 10 false *f 1.188,3.792 1.573,4.01 0.385,0.219 10 false *d 2.635,3.729 3.021,3.948 0.385,0.219 10 false *g 2.708,2.427 3.052,2.719 0.344,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 6


Right camera adjustment only

·

Adjustment of 4 cameras

E287104C01
4.833,3.344 5.083,3 false 2.417,1.5 2.875,1.5 false 4.26,1.5 4.75,1.5 false 3.25,4.469 3.573,4.135 false 3.917,4.469 3.792,4.073 false 5,4.031 5.25,4.344 false 5,1.115 5.25,0.833 false 4.292,1.073 5,0.417 false 2.823,1.083 2.406,0.667 false 3.667,1.083 3.844,0.76 false 4.302,1.771 4.823,1.771 false 4.302,2.552 4.823,2.552 false 4.292,4.094 4.542,4.406 false 2.5,4.417 2.823,4.083 false 2.313,1.792 2.833,1.792 false 2.313,2.552 2.833,2.552 false 2.219,0.521 2.51,0.75 0.292,0.229 10 false *a 5.052,0.333 6.302,0.5 1.25,0.167 10 false *a 4.875,1.698 5.708,1.865 0.833,0.167 10 false *b 3.865,4.5 4.115,4.719 0.25,0.219 10 false *b 3.854,0.646 4.083,0.896 0.229,0.25 10 false *b 2.25,1.438 2.667,1.604 0.417,0.167 10 false *g 4.802,1.417 5.219,1.583 0.417,0.167 10 false *h 5.135,2.917 5.552,3.083 0.417,0.167 10 false *c 5.302,0.75 5.719,0.917 0.417,0.167 10 false *e 5.229,4.385 5.646,4.552 0.417,0.167 10 false *f 3.063,4.5 3.479,4.667 0.417,0.167 10 false *d 4.865,2.479 5.698,2.646 0.833,0.167 10 false *b 4.531,4.448 4.948,4.615 0.417,0.167 10 false *a 2.365,4.406 2.781,4.573 0.417,0.167 10 false *a 2.125,1.719 2.958,1.885 0.833,0.167 10 false *b 2.125,2.458 2.958,2.625 0.833,0.167 10 false *b
*a Cross Check Marker *b Check Marker
*c String 1 *d String 2
*e String 3 *f String 4
*g String 5 *h String 6





c.

Marker positions

i.

Set the check markers at the positions shown in the illustration.

E287105C01
1.594,2.135 1.594,1.938 1.594,1.938 1.927,1.938 false 1.594,4.073 1.594,3.875 1.594,3.875 1.927,3.875 false 3.76,0.5 3.76,0.198 3.76,0.198 4.094,0.198 false 4.927,3.281 4.927,3.125 4.927,3.125 4.646,3.125 false 3.385,0.5 3.385,0.198 3.385,0.198 3.073,0.198 false 5.5,3.073 5.5,2.917 5.5,2.917 5.219,2.917 false 6.073,2.75 6.073,2.594 6.073,2.594 5.792,2.594 false 6.656,2.531 6.656,2.375 6.656,2.375 6.375,2.375 false 3.313,5.094 3.406,4.99 false 3.167,5.458 3.24,5.333 false 3.802,5.104 3.729,4.99 false 4,5.469 3.927,5.333 false 1.51,2.167 1.823,2.365 0.313,0.198 10 false *a 1.531,4.104 1.844,4.302 0.313,0.198 10 false *b 3.073,5.479 3.385,5.677 0.313,0.198 10 false *c 3.938,5.479 4.25,5.677 0.313,0.198 10 false *c 4.865,3.302 5.177,3.5 0.313,0.198 10 false *e 6,2.76 6.313,2.958 0.313,0.198 10 false *g 6.583,2.573 6.896,2.771 0.313,0.198 10 false *h 4.135,0.125 4.448,0.323 0.313,0.198 10 false *d 3.208,5.125 3.521,5.323 0.313,0.198 10 false *d 2.885,0.135 3.198,0.333 0.313,0.198 10 false *d 3.74,5.125 4.052,5.323 0.313,0.198 10 false *d 5.438,3.115 5.75,3.313 0.313,0.198 10 false *f
*a 4800 mm (15.74 ft.) (for Bar Type Radiator Grille)
4900 mm (16.07 ft.) (for Mesh Type Radiator Grille)
*b 1500 mm (4.92 ft.)
*c 1400 mm (4.60 ft.) *d 693 mm (2.27 ft.)
*e 1500 mm (4.92 ft.) *f 1700 mm (5.58 ft.)
*g 3000 mm (9.84 ft.) *h 3200 mm (10.50 ft.)





PROCEDURE 2: SET DATUM POINTS


a.

Extend the datum line (string 1).

i.
E450891C01
2.25,2.573 2.052,2.573 2.052,2.573 1.677,2.698 false 2.219,3.031 1.969,3.031 1.969,3.031 1.667,2.833 false 2.271,2.938 2.583,3.135 0.313,0.198 10 false *a 2.302,2.479 2.615,2.677 0.313,0.198 10 false *b
*a Mark A
*b Weight


Hang a weight with a pointed tip and accurately mark the center position on the road surface. (Mark A)

NOTICE:

Make sure that the weight hangs straight down from the string.



ii.

Repeat the procedure to mark the right side. (Mark B)


iii.
E287139C01
1.01,2.771 1.292,2.458 false 2.417,2.74 2.125,2.458 false 2.385,2.458 2.542,2.073 false 2.594,1.969 2.875,2.135 0.281,0.167 10 false *a 0.885,2.802 1.135,2.938 0.25,0.135 10 false *b 2.385,2.792 2.646,2.969 0.26,0.177 10 false *c
*a String 1
*b Mark A
*c Mark B


Secure string 1 so that it passes through marks A and B on the left and right sides.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.




b.

Extend the vehicle center line (string 2).

i.

Hang a weight with a pointed tip so that it passes through the center of the front television camera assembly and accurately mark the center position on the road surface. (Mark C)

E450892C01
0.542,2.344 0.792,2.344 0.792,2.344 1.271,1.25 true 1.917,0.083 1.656,0.083 1.656,0.083 1.344,0.406 true 2.083,2.427 1.823,2.427 1.823,2.427 1.344,1.729 true 3.094,2.146 3.344,2.146 3.344,2.146 3.625,2.396 false 4,2.646 3.74,2.646 3.74,2.646 3.656,2.49 false 0.354,2.25 0.667,2.406 0.313,0.156 10 false *1 2.135,2.344 2.448,2.5 0.313,0.156 10 false *a 2.917,2.042 3.229,2.198 0.313,0.156 10 false *b 1.948,0 2.26,0.156 0.313,0.156 10 false *c 4.042,2.552 4.354,2.729 0.313,0.177 10 false *d
*1 Front Television Camera Assembly - -
*a Center Point *b Weight
*c String *d Mark C



ii.

Hang a weight with a pointed tip from the center of the rear emblem and accurately mark the center position on the road surface. (Mark D)

E450893C01
2.719,2.625 3.125,2.625 true 5.177,1.552 5.615,2.156 5.615,2.156 5.865,2.156 true 5.167,1.927 5.646,2.5 5.646,2.5 5.896,2.5 true 2.688,2.531 2.542,2.656 2.542,2.656 2.281,2.656 true 2.094,2.552 2.406,2.708 0.313,0.156 10 false *b 5.948,2.406 6.198,2.615 0.25,0.208 10 true *a 3.177,2.521 3.49,2.677 0.313,0.156 10 false *d 4.844,0.49 5.021,0.646 0.177,0.156 10 true *e 5.917,2.063 6.229,2.219 0.313,0.156 10 false *c 5.344,0.49 5.521,0.646 0.177,0.156 10 true *e
*a Center *b Weight
*c String *d Mark D
*e Equal on both sides - -



iii.
E287140C01
1.719,1.333 2.229,0.896 false 2.219,2.927 2.583,2.427 false 1,2.188 1.708,2.917 false 1.719,3.208 2.104,3.573 false 1.375,3.969 1.719,3.656 false 0.802,2.083 1.021,2.281 0.219,0.198 10 false *a 2.271,0.781 2.458,0.958 0.188,0.177 10 false *d 2.156,3.542 2.385,3.729 0.229,0.188 10 false *e 2.625,2.313 2.875,2.51 0.25,0.198 10 false *b 1.24,3.979 1.427,4.177 0.188,0.198 10 false *c
*a Datum Point
*b String 1
*c String 2
*d Mark C
*e Mark D


Secure string 2 so that it passes through marks C and D at the front and rear of the vehicle.

NOTICE:

When securing string 2, check that there is no slack and the string is not twisted.


HINT:

Set the point where strings 1 and 2 intersect as the datum point.





PROCEDURE 3: SET MARKERS (when checking front)


a.
E287141C01
1.719,1.208 2.24,0.76 false 2.594,3.448 2.333,3.156 false 2.01,4.104 1.708,3.76 false 1.125,3.781 1.323,3.781 1.323,3.781 1.719,3.156 false 0.583,1.917 0.771,1.74 0.771,1.74 0.99,1.74 false 1.031,1.667 1.281,1.865 0.25,0.198 10 false *a 2.302,0.677 2.583,0.875 0.281,0.198 10 false *e 2.635,3.479 2.865,3.656 0.229,0.177 10 false *c 2.063,4.125 2.281,4.292 0.219,0.167 10 false *d 0.958,3.708 1.208,3.885 0.25,0.177 10 false *b
*a 4800 mm (15.74 ft.) (for Bar Type Radiator Grille)
4900 mm (16.07 ft.) (for Mesh Type Radiator Grille)
*b Datum Point
*c String 1
*d String 2
*e Mark E


In front of the vehicle, extend string 3 perpendicular to the vehicle center line (string 2) and place a marker.

i.

Mark the position on string 2 in front of the vehicle, 4800 mm (15.74 ft.)*1 or 4900 mm (16.07 ft.)*2 from the datum point. (Mark E)

*1: for Bar Type Radiator Grille

*2: for Mesh Type Radiator Grille



ii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



iv.
E287142C01
0.771,0.927 1.094,1.25 false 1.115,1.656 1.396,1.25 false 2.281,1.688 2.042,1.25 false 2.688,1.438 2.313,1.25 false 2.688,0.573 2.583,0.573 2.583,0.573 2.458,1.25 false 2.042,4.073 1.719,3.76 false 2.521,3.51 2.198,3.198 false 1.938,0.938 2.094,0.448 2.094,0.448 2.25,0.448 false 1.417,0.938 1.26,0.51 1.26,0.51 1.104,0.51 false 0.917,0.417 1.115,0.583 0.198,0.167 10 false *a 0.594,0.823 0.802,1.01 0.208,0.188 10 false *g 0.938,1.635 1.167,1.792 0.229,0.156 10 false *e 2.333,1.688 2.51,1.833 0.177,0.146 10 false *f 2.74,1.427 2.979,1.583 0.24,0.156 10 false *h 2.74,0.5 2.948,0.656 0.208,0.156 10 false *d 2.583,3.531 2.792,3.688 0.208,0.156 10 false *b 2.083,4.073 2.292,4.24 0.208,0.167 10 false *c 2.292,0.354 2.521,0.51 0.229,0.156 10 false *a
*a 1400 mm (4.60 ft.)
*b String 1
*c String 2
*d String 3
*e Mark F
*f Mark G
*g Mark H
*h Mark I


Secure string 3 so that it passes through marks F and G as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string 3, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I).


vi.
E287109C01
0.75,1.667 1.063,1.25 false 2.333,1.667 1.917,1.125 false 1.083,1.083 0.833,0.833 false 2.052,1.083 1.833,0.333 false 1.385,1.083 1.167,0.5 false 2.323,0.635 2.323,0.333 2.323,0.333 2.583,0.333 false 2.333,1.083 2.667,0.75 2.667,0.75 2.833,0.75 false 3.25,1.333 3.25,1.104 3.25,1.104 3.052,1.104 false 2.781,1.708 2.365,1.229 false 0.604,1.688 0.823,1.875 0.219,0.188 10 false *c 2.313,1.698 2.51,1.854 0.198,0.156 10 false *d 0.677,0.688 0.896,0.865 0.219,0.177 10 false *g 1.052,0.354 1.292,0.521 0.24,0.167 10 false *e 1.708,0.188 1.948,0.333 0.24,0.146 10 false *f 2.885,0.667 3.063,0.813 0.177,0.146 10 false *h 2.635,0.25 2.865,0.417 0.229,0.167 10 false *a 3.188,1.354 3.406,1.521 0.219,0.167 10 false *b 2.74,1.708 2.958,1.896 0.219,0.188 10 false *c
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c Cross Check Marker
*d Check Marker
*e Mark F
*f Mark G
*g Mark H
*h Mark I


Place and secure the cross check markers, centered on marks H and I.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.




vii.

Place the check marker between marks F and G.


viii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 4: SET MARKERS (When checking rear)


a.

To the rear of the vehicle, extend string 4 perpendicular to the vehicle center line (string 2) and place a check marker.

i.
E287143C01
1.719,1.104 2.208,0.854 false 0.948,2.26 1.167,2.26 1.167,2.26 1.719,2.844 false 1.229,4.021 1.688,3.573 false 0.698,3.104 0.896,3.104 0.896,3.104 1.094,3.271 false 2.74,3.24 2.552,2.833 false 0.531,3.031 1.604,3.229 1.073,0.198 10 false *a 1.063,3.99 1.542,4.25 0.479,0.26 10 false *e 0.792,2.198 1.615,2.458 0.823,0.26 10 false *b 2.271,0.802 3.094,1.063 0.823,0.26 10 false *d 2.75,3.26 3.229,3.521 0.479,0.26 10 false *c
*a 1500 mm (4.92 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark J


Mark a position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


ii.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



iv.
E287144C01
1.708,0.896 2.208,0.542 false 0.583,2.063 1.094,2.688 false 1,3.052 1.396,3.354 false 0.677,3.802 1.094,3.354 false 2.385,3.042 2.073,3.344 false 2.875,3.646 2.677,3.344 false 2.615,3.802 2.313,3.344 false 2.167,3.969 1.969,3.667 false 1.188,3.979 1.417,3.667 false 2.292,0.5 2.75,0.698 0.458,0.198 10 false *c 0.385,1.969 0.844,2.167 0.458,0.198 10 false *b 0.844,2.938 1.302,3.135 0.458,0.198 10 false *f 2.438,2.969 2.896,3.167 0.458,0.198 10 false *e 2.844,3.698 3.302,3.896 0.458,0.198 10 false *d 2.542,3.854 3,4.052 0.458,0.198 10 false *h 2.167,4.042 3.104,4.26 0.938,0.219 10 false *a 1.115,4 2.052,4.219 0.938,0.219 10 false *a 0.552,3.833 1.01,4.031 0.458,0.198 10 false *g
*a 1400 mm (4.60 ft.)
*b String 1
*c String 2
*d String 4
*e Mark K
*f Mark L
*g Mark M
*h Mark N


Secure string 4 so that it passes through marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string 4, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


vi.
E287106C01
2.583,2.948 2.833,2.667 false 1.917,4.25 1.833,3.667 false 1.375,3.604 1.302,3.396 1.302,3.396 1.385,3.396 false 2.052,3.604 2.135,3.396 2.135,3.396 2.052,3.396 false 3.167,3.885 3.167,3.635 3.167,3.635 3.052,3.635 false 1.5,4 1.5,3.729 1.5,3.729 1.344,3.729 false 2.583,4.25 2.333,4.021 false 2.354,3.74 2.781,3.969 false 0.792,4.063 0.99,3.656 false 1.115,3.625 0.792,3.281 false 2.323,3.635 2.573,3.354 false 2.885,2.583 3.302,2.75 0.417,0.167 10 false *f 2.802,3.99 3.167,4.344 0.365,0.354 10 false *d 1.875,4.313 2.708,4.479 0.833,0.167 10 false *e 1.427,4.042 2.01,4.208 0.583,0.167 10 false *c 2.531,4.292 3.115,4.458 0.583,0.167 10 false *a 3.115,3.917 3.396,4.135 0.281,0.219 10 false *b 1.448,3.333 1.698,3.5 0.25,0.167 10 false *h 1.865,3.333 2.115,3.5 0.25,0.167 10 false *g 0.677,4.125 1.375,4.458 0.698,0.333 10 false *d 0.719,3.146 1.417,3.479 0.698,0.333 10 false *i 2.552,3.208 3.25,3.542 0.698,0.333 10 false *j
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g Mark K
*h Mark L
*i Mark M
*j Mark N


Place and secure the cross check markers, centered on marks M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




vii.

Place the check marker between marks K and L.


viii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 5: SET MARKERS (When checking left side)


a.

To the left side of the vehicle, extend string 5 parallel to the vehicle center line (string 2) and place a check marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 4800 mm (15.74 ft.) (for Bar Type Radiator Grille)
4900 mm (16.07 ft.) (for Mesh Type Radiator Grille)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 4800 mm (15.74 ft.)*1 or 4900 mm (16.07 ft.)*2 from the datum point. (Mark E)

*1: for Bar Type Radiator Grille

*2: for Mesh Type Radiator Grille



ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287146C01
0.563,0.5 1.094,1.073 false 1.135,1.438 1.406,1.063 false 2.042,1.052 2.177,0.583 false 2.552,1.063 2.792,0.594 false 2.583,3.719 2.74,3.958 false 2.052,3.719 2.208,3.958 false 1.104,3.417 1.385,3.708 false 0.781,4.073 1.083,3.708 false 1.365,4.021 1.469,4.281 false 1.365,0.771 1.438,0.438 false 0.385,0.417 0.698,0.615 0.313,0.198 10 false *f 1.385,0.26 2.021,0.469 0.635,0.208 10 false *a 0.99,1.469 1.302,1.667 0.313,0.198 10 false *d 2.156,0.427 2.469,0.625 0.313,0.198 10 false *e 2.781,0.427 3.188,0.667 0.406,0.24 10 false *b 2.719,3.99 3.125,4.229 0.406,0.24 10 false *c 2.156,3.99 2.469,4.188 0.313,0.198 10 false *g 1.427,4.313 2.063,4.521 0.635,0.208 10 false *a 0.656,4.094 1.063,4.365 0.406,0.271 10 false *i 0.938,3.323 1.25,3.521 0.313,0.198 10 false *h
*a 1400 mm (4.60 ft.)
*b String 3
*c String 4
*d Mark F
*e Mark G
*f Mark H
*g Mark K
*h Mark L
*i Mark M


Secure strings 3 and 4 so that they pass through marks F and G, marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings 3 and 4, 1400 mm (4.60 ft.) to the left of the vehicle center line (string 2). (Marks H and M)


ix.
E395048C01
2.396,2.958 2.583,2.677 false 1.563,3.938 1.698,3.823 false 2.5,1 2.688,0.719 false 0.656,3.594 0.448,3.333 false 1.094,0.688 1.281,0.406 false 0.865,1.271 1.094,1.021 false 0.865,3.854 1.094,3.604 false 2.563,2.51 2.875,2.708 0.313,0.198 10 false *a 1.385,3.906 1.698,4.104 0.313,0.198 10 false *b 2.656,0.552 2.969,0.75 0.313,0.198 10 false *c 0.333,3.167 0.646,3.365 0.313,0.198 10 false *d 1.25,0.25 1.563,0.448 0.313,0.198 10 false *e 0.698,1.292 1.01,1.49 0.313,0.198 10 false *f 0.719,3.906 1.031,4.104 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f Mark H
*g Mark M


Secure string 5 so that it passes through marks H and M as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.
E287147C04
0.771,0.771 1.385,1.021 false 0.781,0.385 1.396,0.635 false 1.406,1.531 1.24,1.365 false 1.385,1.677 1.229,1.792 false 1.385,2.208 1.188,2.083 false 1.396,2.354 1.281,2.51 false 2.531,2.979 2.656,3.219 false 1.385,3.594 1.563,3.75 false 0.24,2.354 0.125,2.354 0.125,2.354 0.125,2.635 false 0.51,2.354 0.396,2.354 0.396,2.354 0.396,2.635 false 0.802,2.354 0.688,2.354 0.688,2.354 0.688,2.635 false 1.063,2.51 0.948,2.51 0.948,2.51 0.948,2.792 false 0.615,0.313 1.073,0.51 0.458,0.198 10 false *f 0.604,0.677 0.917,0.885 0.313,0.208 10 false *g 1.104,1.24 1.563,1.438 0.458,0.198 10 false *l 1.073,1.792 1.531,1.99 0.458,0.198 10 false *k 1.073,1.969 1.531,2.167 0.458,0.198 10 false *j 1.208,2.552 1.667,2.75 0.458,0.198 10 false *i 2.625,3.281 3.083,3.479 0.458,0.198 10 false *e 1.615,3.771 2.073,3.969 0.458,0.198 10 false *h 0.865,2.781 1.802,3.052 0.938,0.271 10 false *a 0.594,2.698 1.531,2.969 0.938,0.271 10 false *b 0.333,2.677 1.271,2.948 0.938,0.271 10 false *c 0.042,2.677 0.313,2.896 0.271,0.219 10 false *d
*a 1500 mm (4.92 ft.)
*b 1700 mm (5.58 ft.)
*c 3000 mm (9.84 ft.)
*d 3200 mm (10.50 ft.)
*e String 1
*f String 5
*g Mark H
*h Mark M
*i Mark O
*j Mark P
*k Mark Q
*l Mark R


Make marks on string 5 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.50 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xi.
E287107C01
1.094,3.615 0.75,3.333 false 1.438,0.167 1.104,0.167 1.104,0.167 1.104,0.396 false 2,0.5 1.135,0.917 false 1.073,3.75 0.667,4.25 false 1.583,4 1.583,3.74 1.583,3.74 1.438,3.74 false 0.885,1.219 1.104,1.031 false 1.104,0.667 0.667,0.5 false 2.583,3.031 2.833,2.74 false 0.885,2.604 1.115,2.406 false 0.875,2.052 1.115,2.229 false 1.229,1.896 1.115,1.75 false 1.333,1.396 1.115,1.573 false 0.365,1.031 0.198,1.031 0.198,1.031 0.198,1.5 false 1.063,2.323 0.813,2.323 false 1.073,1.667 0.823,1.667 false 1.49,0.083 2.073,0.25 0.583,0.167 10 false *b 0.49,0.406 0.906,0.573 0.417,0.167 10 false *g 2.052,0.417 3.302,0.583 1.25,0.167 10 false *d 0.646,2.25 1.479,2.417 0.833,0.167 10 false *e 0.573,4.271 2.073,4.438 1.5,0.167 10 false *d 0.594,3.229 0.927,3.396 0.333,0.167 10 false *i 1.51,4.042 2.094,4.208 0.583,0.167 10 false *c 2.885,2.604 3.302,2.771 0.417,0.167 10 false *f 0.719,1.25 1.052,1.417 0.333,0.167 10 false *h 1.292,1.25 1.625,1.417 0.333,0.167 10 false *m 1.177,1.927 1.51,2.094 0.333,0.167 10 false *l 0.75,1.906 1.083,2.073 0.333,0.167 10 false *k 0.792,2.646 1.125,2.813 0.333,0.167 10 false *j 0.146,1.552 0.729,1.719 0.583,0.167 10 false *a 0.594,1.583 1.427,1.75 0.833,0.167 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 5
*h Mark H
*i Mark M
*j Mark O
*k Mark P
*l Mark Q
*m Mark R


Place and secure the cross check markers, centered on marks H and M.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks O and P, and marks Q and R.


xiii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 6: SET MARKERS (When checking right side)


a.

At the right side of the vehicle, extend string 6 parallel to the vehicle and place a marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 4800 mm (15.74 ft.) (for Bar Type Radiator Grille)
4900 mm (16.07 ft.) (for Mesh Type Radiator Grille)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 4800 mm (15.74 ft.)*1 or 4900 mm (16.07 ft.)*2 from the datum point. (Mark E)

*1: for Bar Type Radiator Grille

*2: for Mesh Type Radiator Grille



ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287712C01
0.927,0.49 1.344,1.052 false 2,1.063 2.229,1.469 false 2.313,1.063 2.792,0.385 false 2.5,1.063 2.896,1.323 false 2.813,3.615 2.906,3.354 false 2.313,3.635 2.573,3.948 false 2.01,3.615 2.219,3.354 false 1.354,3.625 1.125,3.344 false 1.969,3.938 2.094,4.188 false 1.99,0.76 2.146,0.448 false 2.115,0.313 3.188,0.51 1.073,0.198 10 false *a 2.052,4.229 3.125,4.427 1.073,0.198 10 false *a 0.708,0.385 1.021,0.583 0.313,0.198 10 false *d 2.833,0.24 3.146,0.438 0.313,0.198 10 false *f 2.969,1.302 3.417,1.531 0.448,0.229 10 false *b 2.26,1.5 2.573,1.698 0.313,0.198 10 false *e 2.948,3.271 3.396,3.5 0.448,0.229 10 false *c 2.271,3.271 2.583,3.469 0.313,0.198 10 false *g 2.594,3.979 2.906,4.177 0.313,0.198 10 false *i 0.896,3.219 1.208,3.417 0.313,0.198 10 false *h
*a 1400 mm (4.60 ft.)
*b String 3
*c String 4
*d Mark F
*e Mark G
*f Mark I
*g Mark K
*h Mark L
*i Mark N


Secure strings 3 and 4 so that they pass through marks F and G and marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings 3 and 4, 1400 mm (4.60 ft.) to the left of the vehicle center line (string 2). (Marks I and N)


ix.
E395049C01
2.51,2.948 2.688,2.656 false 1.51,3.906 1.719,3.813 false 2.573,0.99 2.719,0.74 false 0.688,3.594 0.458,3.313 false 2.313,0.688 2.49,0.396 false 2.313,1.01 2.604,1.354 false 2.313,3.594 2.604,3.938 false 2.667,2.5 2.979,2.698 0.313,0.198 10 false *a 1.323,3.875 1.635,4.073 0.313,0.198 10 false *b 2.698,0.594 3.01,0.792 0.313,0.198 10 false *c 0.302,3.156 0.615,3.354 0.313,0.198 10 false *d 2.5,0.229 2.813,0.427 0.313,0.198 10 false *e 2.646,1.365 2.958,1.563 0.313,0.198 10 false *f 2.635,3.938 2.948,4.135 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 6
*f Mark I
*g Mark N


Secure string 6 so that it passes through marks I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.
E287713C14
2.01,0.781 2.365,0.573 false 1.823,0.729 2.021,1.021 false 2.26,1.333 2.021,1.531 false 2.229,1.833 2.031,1.667 false 1.885,2.01 2.01,2.219 false 1.896,2.531 2.01,2.344 false 0.656,3.125 0.771,3.125 0.771,3.125 0.875,2.969 false 2.99,2.76 2.99,2.563 2.99,2.563 3.167,2.563 false 1.854,3.792 2.01,3.615 false 2.448,2.75 2.448,2.552 2.448,2.552 2.604,2.552 false 2.729,2.75 2.729,2.552 2.729,2.552 2.885,2.552 false 2.177,2.74 2.177,2.542 2.177,2.542 2.333,2.542 false 1.646,0.615 1.958,0.813 0.313,0.198 10 false *g 2.427,0.51 2.958,0.75 0.531,0.24 10 false *f 2.313,1.229 2.625,1.427 0.313,0.198 10 false *l 2.219,1.865 2.531,2.063 0.313,0.198 10 false *k 1.802,1.802 2.115,2 0.313,0.198 10 false *j 1.833,2.552 2.146,2.75 0.313,0.198 10 false *i 0.438,3.042 0.906,3.292 0.469,0.25 10 false *e 1.677,3.76 1.99,3.958 0.313,0.198 10 false *h 2.927,2.792 3.26,3.021 0.333,0.229 10 false *d 2.677,2.792 2.969,3.031 0.292,0.24 10 false *c 2.104,2.792 3.063,3 0.958,0.208 10 false *a 2.385,2.792 3.344,3 0.958,0.208 10 false *b
*a 1500 mm (4.92 ft.)
*b 1700 mm (5.58 ft.)
*c 3000 mm (9.84 ft.)
*d 3200 mm (10.50 ft.)
*e String 1
*f String 6
*g Mark I
*h Mark N
*i Mark S
*j Mark T
*k Mark U
*l Mark V


Make marks on string 6 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.50 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xi.
E287108C01
1.5,0.583 2.292,0.917 false 2.563,1.406 2.323,1.573 false 2.615,1.896 2.323,1.76 false 2.198,2.583 2.333,2.406 false 2.74,3.375 2.365,3.25 false 3.167,1.333 3.167,1.031 3.167,1.031 3.063,1.031 false 2.5,3.021 2.75,2.729 false 2.323,0.667 2.75,0.333 false 2.323,0.396 2.323,0.167 2.323,0.167 2.083,0.167 false 1.99,3.74 1.833,3.74 1.833,3.74 1.833,4.25 false 2.333,3.615 2.552,3.927 false 2.198,2.01 2.333,2.229 false 2.333,1.01 2.75,0.667 false 2.656,1.667 2.354,1.667 false 2.656,2.302 2.354,2.302 false 1.292,0.51 2.542,0.677 1.25,0.167 10 false *d 2.719,1.604 3.333,1.76 0.615,0.156 10 false *e 2.74,3.375 3.125,3.646 0.385,0.271 10 false *d 1.781,4.292 2.365,4.458 0.583,0.167 10 false *c 2.604,3.927 2.938,4.094 0.333,0.167 10 false *i 2.802,2.583 3.219,2.75 0.417,0.167 10 false *f 3.104,1.385 3.417,1.594 0.313,0.208 10 false *a 2.802,0.583 3.135,0.75 0.333,0.167 10 false *h 2.802,0.25 3.219,0.417 0.417,0.167 10 false *g 1.917,0.104 2.5,0.271 0.583,0.167 10 false *b 2.583,1.323 2.917,1.49 0.333,0.167 10 false *m 2.656,1.865 2.99,2.031 0.333,0.167 10 false *l 2.135,1.844 2.385,2.042 0.25,0.198 10 false *k 2.135,2.625 2.469,2.792 0.333,0.167 10 false *j 2.698,2.229 3.313,2.385 0.615,0.156 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 6
*h Mark I
*i Mark N
*j Mark S
*k Mark T
*l Mark U
*m Mark V


Place and secure the cross check markers, centered on marks I and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks S and T, and marks U and V.


xiii.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 7: SET MARKERS (When checking all cameras)


a.

Set markers in every direction from the vehicle.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1500 mm (4.92 ft.)
*b 4800 mm (15.74 ft.) (for Bar Type Radiator Grille)
4900 mm (16.07 ft.) (for Mesh Type Radiator Grille)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string 2 in front of the vehicle, 4800 mm (15.74 ft.)*1 or 4900 mm (16.07 ft.)*2 from the datum point. (Mark E)

*1: for Bar Type Radiator Grille

*2: for Mesh Type Radiator Grille



ii.

Mark the position on string 2 to the rear of the vehicle, 1500 mm (4.92 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Secure the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Secure the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287148C01
0.615,0.708 0.76,0.708 0.76,0.708 1.094,1.052 false 1.042,1.552 1.188,1.552 1.188,1.552 1.396,1.063 false 2.344,1.531 2.167,1.531 2.167,1.531 2.042,1.063 false 2.76,0.292 2.583,0.292 2.583,0.292 2.354,1.073 false 2.865,0.719 2.688,0.719 2.688,0.719 2.573,1.052 false 2.292,3.135 2.146,3.135 2.146,3.135 2.042,3.448 false 2.75,4.177 2.604,4.177 2.604,4.177 2.365,3.458 false 2.76,3.75 2.646,3.75 2.646,3.75 2.563,3.458 false 2.021,4.323 1.906,4.323 1.906,4.323 1.719,4.042 false 0.833,3.719 0.969,3.719 0.969,3.719 1.083,3.458 false 0.979,3.115 1.115,3.115 1.115,3.115 1.406,3.448 false 1.375,0.76 1.271,0.375 false 2,0.76 2.125,0.396 false 1.313,3.99 1.385,3.76 false 2.135,3.99 2.073,3.76 false 1.188,0.229 2.26,0.427 1.073,0.198 10 false *a 2.083,0.24 3.156,0.438 1.073,0.198 10 false *a 0.417,0.646 0.865,0.833 0.448,0.188 10 false *g 2.948,0.656 3.396,0.844 0.448,0.188 10 false *c 2.833,0.229 3.281,0.417 0.448,0.188 10 false *h 0.781,1.479 1.229,1.667 0.448,0.188 10 false *e 2.396,1.469 2.844,1.656 0.448,0.188 10 false *f 2.354,3.083 2.802,3.271 0.448,0.188 10 false *i 0.802,3.063 1.25,3.25 0.448,0.188 10 false *j 0.667,3.667 1.115,3.854 0.448,0.188 10 false *k 2.813,4.125 3.26,4.313 0.448,0.188 10 false *l 2.833,3.698 3.281,3.885 0.448,0.188 10 false *d 2.094,4.26 2.542,4.448 0.448,0.188 10 false *b 2.094,4.031 2.823,4.25 0.729,0.219 10 false *a 1.208,4.01 1.938,4.229 0.729,0.219 10 false *a
*a 1400 mm (4.60 ft.)
*b String 2
*c String 3
*d String 4
*e Mark F
*f Mark G
*g Mark H
*h Mark I
*i Mark K
*j Mark L
*k Mark M
*l Mark N


Secure strings 3 and 4 so that they pass through marks F, G, K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark string 3, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I)


ix.

Mark string 4, 1400 mm (4.60 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


x.
E287132C02
1.094,0.688 1.292,0.271 false 2.302,0.667 2.688,0.177 false 2.604,1 2.875,0.677 false 2.625,1.375 2.302,1.01 false 0.781,1.385 1.104,1 false 0.458,3.26 0.698,3.583 false 0.771,4.031 1.094,3.594 false 1.552,3.833 1.708,3.74 false 2.646,3.948 2.313,3.594 false 2.635,2.646 2.469,2.958 false 1.344,0.198 1.802,0.396 0.458,0.198 10 false *e 2.75,0.104 3.208,0.302 0.458,0.198 10 false *f 2.938,0.604 3.396,0.802 0.458,0.198 10 false *c 2.688,1.396 3.146,1.594 0.458,0.198 10 false *h 0.625,1.417 1.083,1.615 0.458,0.198 10 false *g 0.313,3.104 0.771,3.302 0.458,0.198 10 false *d 0.646,4.073 1.104,4.271 0.458,0.198 10 false *i 1.375,3.875 1.833,4.073 0.458,0.198 10 false *b 2.667,4 3.125,4.198 0.458,0.198 10 false *j 2.729,2.573 3.188,2.771 0.458,0.198 10 false *a
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f String 6
*g Mark H
*h Mark I
*i Mark M
*j Mark N


Secure strings 5 and 6 so that they pass through marks H, M, I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xi.
E288356C02
2.542,3.885 2.354,3.885 2.354,3.885 2.281,3.604 false 0.396,3.26 0.531,3.26 0.531,3.26 0.552,2.979 false 2.344,2.615 2.188,2.615 2.188,2.615 2.177,2.75 false 2.594,2.615 2.479,2.615 2.479,2.615 2.469,2.75 false 2.875,2.615 2.74,2.615 2.74,2.615 2.729,2.75 false 3.167,2.625 3.031,2.625 3.031,2.625 3.021,2.76 false 0.781,0.75 0.635,0.5 0.635,0.5 0.479,0.5 false 1.396,0.76 1.25,0.51 1.25,0.51 1.094,0.51 false 2.021,0.719 2.146,0.458 2.146,0.458 2.385,0.458 false 2.344,1.021 2.469,0.76 2.469,0.76 2.708,0.76 false 2.021,1.521 2.115,1.313 2.115,1.313 2.24,1.313 false 2.031,2.208 2.125,2 2.125,2 2.25,2 false 0.792,1.531 0.677,1.333 0.677,1.333 0.479,1.333 false 0.792,2.208 0.677,2.01 0.677,2.01 0.479,2.01 false 0.771,2.354 0.688,2.5 0.688,2.5 0.542,2.5 false 0.781,1.688 0.698,1.833 0.698,1.833 0.552,1.833 false 1.906,1.865 2.021,1.677 false 1.896,2.542 2.01,2.354 false 2.104,2.76 2.417,2.917 0.313,0.156 10 false *a 2.396,2.771 2.708,2.927 0.313,0.156 10 false *b 2.667,2.75 2.979,2.906 0.313,0.156 10 false *c 2.969,2.771 3.281,2.927 0.313,0.156 10 false *d 0.198,3.177 0.51,3.333 0.313,0.156 10 false *e 0.958,0.448 1.271,0.604 0.313,0.156 10 false *f 2.75,0.677 3.063,0.833 0.313,0.156 10 false *g 2.625,3.813 2.938,3.969 0.313,0.156 10 false *h 0.344,0.438 0.656,0.594 0.313,0.156 10 false *i 2.438,0.396 2.75,0.552 0.313,0.156 10 false *j 0.375,2.458 0.688,2.615 0.313,0.156 10 false *k 0.344,1.948 0.656,2.104 0.313,0.156 10 false *l 0.344,1.75 0.656,1.906 0.313,0.156 10 false *m 0.302,1.271 0.615,1.427 0.313,0.156 10 false *n 1.802,2.552 2.115,2.708 0.313,0.156 10 false *o 2.271,1.927 2.583,2.083 0.313,0.156 10 false *p 1.823,1.875 2.135,2.031 0.313,0.156 10 false *q 2.281,1.24 2.594,1.396 0.313,0.156 10 false *r
*a 1500 mm (4.92 ft.)
*b 1700 mm (5.58 ft.)
*c 3000 mm (9.84 ft.)
*d 3200 mm (10.50 ft.)
*e String 1
*f String 2
*g String 3
*h String 4
*i String 5
*j String 6
*k Mark O
*l Mark P
*m Mark Q
*n Mark R
*o Mark S
*p Mark T
*q Mark U
*r Mark V


Make marks on string 5 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.50 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xii.

Make marks on string 6 that are 1500 mm (4.92 ft.), 1700 mm (5.58 ft.), 3000 mm (9.84 ft.), and 3200 mm (10.50 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xiii.

Place and secure the cross check markers, centered on marks H, I, M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.



E287112C01
4.26,2.052 4.583,1.917 false 4.26,2.792 4.583,2.667 false 4.25,2.25 4.583,2.375 false 4.25,2.99 4.583,3.115 false 2.573,2.385 2.896,2.25 false 2.573,3.115 2.896,2.979 false 2.573,1.927 2.906,2.052 false 2.563,2.667 2.896,2.792 false 4.365,1.406 4.833,0.917 false 4.271,2.896 5.708,2.521 5.708,2.521 4.292,2.135 false 2.5,1.167 2.896,1.427 false 4.26,0.26 4.26,0.167 4.26,0.167 4.677,0.167 false 5.469,1.448 5.635,1.448 5.635,1.448 5.635,1.75 false 2.5,4.667 2.896,4.365 false 4.667,4.667 4.26,4.365 false 3.417,5.469 3.417,4.396 false 3.083,4.75 3.208,4.375 false 4.083,4.75 3.958,4.375 false 4.906,3.708 5.24,3.354 false 3.927,1.146 4.01,1.146 4.01,1.146 3.958,1.438 false 3.24,1.146 3.156,1.146 3.156,1.146 3.198,1.438 false 4.26,1.438 4.438,1.635 false 3.531,1.417 3.729,0.521 false 2.865,2.906 1.156,2.51 1.156,2.51 2.875,2.146 false 2.865,1.271 2.385,0.625 false 4.281,4.51 4.667,5.25 false 2.865,4.51 2.406,5.25 false 3.354,5.5 4.188,5.667 0.833,0.167 10 false *d 2.99,4.781 3.24,4.948 0.25,0.167 10 false *k 2.354,4.677 2.688,4.844 0.333,0.167 10 false *l 4.031,4.792 4.281,4.958 0.25,0.167 10 false *j 4.698,4.698 4.948,4.865 0.25,0.167 10 false *m 5.292,3.302 5.708,3.469 0.417,0.167 10 false *e 4.635,3.063 4.969,3.229 0.333,0.167 10 false *r 4.635,2.583 4.969,2.75 0.333,0.167 10 false *s 4.635,2.323 4.969,2.49 0.333,0.167 10 false *t 4.635,1.833 4.969,2 0.333,0.167 10 false *u 4.75,0.104 5.333,0.271 0.583,0.167 10 false *b 4.885,0.833 6.135,1 1.25,0.167 10 false *c 5.563,1.792 6.146,1.958 0.583,0.167 10 false *a 3.75,1.083 4.083,1.25 0.333,0.167 10 false *g 3.302,1.083 3.635,1.25 0.333,0.167 10 false *f 2.292,1.063 2.625,1.229 0.333,0.167 10 false *h 2.396,1.833 2.667,2.052 0.271,0.219 10 false *q 2.385,2.323 2.719,2.49 0.333,0.167 10 false *p 2.365,2.604 2.698,2.771 0.333,0.167 10 false *o 2.406,3.125 2.74,3.292 0.333,0.167 10 false *n 0.969,2.448 1.802,2.615 0.833,0.167 10 false *d 4.479,1.604 4.813,1.771 0.333,0.167 10 false *i 3.74,0.365 4.323,0.531 0.583,0.167 10 false *d 5.802,2.438 6.635,2.604 0.833,0.167 10 false *d 2.302,0.469 3.552,0.635 1.25,0.167 10 false *c 4.677,5.302 5.927,5.469 1.25,0.167 10 false *c 2.313,5.313 3.563,5.479 1.25,0.167 10 false *c
*a 100 mm (0.33 ft.) *b 800 mm (2.62 ft.)
*c Cross Check Marker *d Check Marker
*e String 1 *f Mark F
*g Mark G *h Mark H
*i Mark I *j Mark K
*k Mark L *l Mark M
*m Mark N *n Mark O
*o Mark P *p Mark Q
*q Mark R *r Mark S
*s Mark T *t Mark U
*u Mark V - -



xiv.

Place check markers between marks F and G, marks K and L, marks O and P, marks Q and R, marks S and T, and marks U and V.


xv.

Perform camera view adjustment (calibration) (procedure 8).




PROCEDURE 8: CAMERA VIEW ADJUSTMENT (CALIBRATION)


a.

Enter diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

NOTICE:

Adjustment must be performed with the engine running. Therefore, apply the parking brake, depress the brake pedal and move the shift lever to P to ensure that the vehicle does not begin moving unexpectedly.



b.
E422909

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E432763

Select "Camera Setting" from the Function Check/Setting I screen to display the Mode Setting(*) screen.

NOTICE:

If "Camera Setting" is not displayed on the screen, turn the ignition switch off, and then turn it ON again and enter the diagnostic mode.



d.
E384441

Select "View Adjustment" on the Mode Setting(*) screen to display the Signal Check(*) screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



e.
E435680

Select "Next" from the Signal Check(*) screen to display the adjustment screen.

NOTICE:
·

When "CHK" (red) is displayed for an item on the Signal Check(*) screen, selecting "Next" will not change to the adjustment screen.

·

Check the Signal Check(*) screen when "CHK" (red) is displayed for an item on the Signal Check(*) screen.




f.

Perform the view adjustment.

E449370C01
0.917,0.833 2.75,0.833 2.75,0.833 2.917,1 true 2,1.271 2.167,1.438 true 1.583,0.208 1.833,0.208 1.833,0.208 2.167,0.542 true 2.854,0.125 2.604,0.125 2.604,0.125 2.531,0.542 true 0.917,1.281 2.75,1.281 2.75,1.281 2.917,1.448 true 2,0.833 2.167,1 true 0.917,1.781 2.75,1.781 2.75,1.781 2.917,1.948 true 2,1.781 2.167,1.948 true 3.438,0.188 3.188,0.188 3.188,0.188 2.938,0.552 true 4.979,2.615 4.729,2.615 4.729,2.615 4.333,1.865 true 5.813,0.208 5.563,0.208 5.563,0.208 5.333,0.5 true 5.76,1.708 5.51,1.708 5.51,1.708 5.156,1.448 true 1.646,2.583 1.896,2.583 1.896,2.583 2.167,2.188 true 2.865,2.698 2.615,2.698 2.615,2.698 2.531,2.198 true 3.51,2.573 3.26,2.573 3.26,2.573 2.917,2.198 true 0.719,0.75 1.031,0.906 0.313,0.156 10 false *a 1.406,0.146 1.719,0.302 0.313,0.156 10 false *b 5.031,2.552 5.344,2.708 0.313,0.156 10 false *c 5.896,0.146 6.208,0.302 0.313,0.156 10 false *d 5.823,1.635 6.135,1.792 0.313,0.156 10 false *e 0.74,1.219 1.052,1.375 0.313,0.156 10 false *a 0.74,1.719 1.052,1.875 0.313,0.156 10 false *a 2.906,0.052 3.219,0.208 0.313,0.156 10 false *a 3.521,0.115 3.833,0.271 0.313,0.156 10 false *b 1.458,2.479 1.771,2.635 0.313,0.156 10 false *b 2.938,2.615 3.25,2.771 0.313,0.156 10 false *a 3.573,2.49 3.885,2.646 0.313,0.156 10 false *b
*a Red Line *b Cross Check Marker (for Connection Judgment)
*c Adjustment Buttons *d Camera Select Buttons
*e Vehicle Height Adjustment Buttons - -


NOTICE:

After replacing a camera, use the camera select buttons to select the replaced camera, and select "New Camera".


i.

Check that the cross check markers displayed on the adjustment screen appear connected.

E271143

NOTICE:
·

Before checking the markers on the adjustment screen, ensure that the cross target bars have been placed correctly.

·

If a cross check marker appears displaced on the adjustment screen, use the camera select buttons to select the corresponding camera, and then use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.

E449371E01
4.781,0.198 6.604,0.448 1.823,0.25 10 false After selecting the button 5.479,1.729 6.844,1.969 1.365,0.24 10 false button selected 0.885,1.885 2.688,2.135 1.802,0.25 10 false When selecting button 5.479,3.49 6.896,3.719 1.417,0.229 10 false button selected 5.479,5.281 6.615,5.479 1.135,0.198 10 false button selected 5.479,7.198 6.969,7.375 1.49,0.177 10 false button selected



HINT:

To repeat the adjustment, select "All View Reset" to return all adjustment values to their initial values.



ii.

Check that the target bars do not protrude outside the red frames displayed on the adjustment screen.

E271144

NOTICE:
·

Before checking the adjustment screen, ensure that the check markers have been placed correctly.

·

If a target bar protrudes outside a red frame on the adjustment screen, use the camera select buttons to select the corresponding camera, and use the adjustment buttons or vehicle height adjustment buttons to adjust the screen.

E449371E01
4.781,0.198 6.604,0.448 1.823,0.25 10 false After selecting the button 5.479,1.729 6.844,1.969 1.365,0.24 10 false button selected 0.885,1.885 2.688,2.135 1.802,0.25 10 false When selecting button 5.479,3.49 6.896,3.719 1.417,0.229 10 false button selected 5.479,5.281 6.615,5.479 1.135,0.198 10 false button selected 5.479,7.198 6.969,7.375 1.49,0.177 10 false button selected

HINT:

To repeat the adjustment, select "All View Reset" to return all adjustment values to their initial values.






g.
E372775

When all adjustments are completed, press "OK".


h.

If data writing ends normally, "The view data writing was completed." is displayed.


i.

Select "OK".




PROCEDURE 9: STEERING ANGLE SETTING


a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.

HINT:

Before stopping the vehicle, move the vehicle slightly backward and forward to ensure that both the steering wheel and the tires point straight ahead.



ii.

Adjust the tire pressure to the specified value(s).



b.

Enter diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

NOTICE:

Adjustment must be performed with the engine running. Therefore, apply the parking brake, depress the brake pedal and move the shift lever to P to ensure that the vehicle does not begin moving unexpectedly.



c.
E422909

Select "Function Check/Setting" on the "Service Menu" screen.


d.
E432763

Select "Camera Setting" from the Function Check/Setting I screen to display the Mode Setting(*) screen.

NOTICE:

If "Camera Setting" is not displayed on the screen, turn the ignition switch off, and then turn it ON again and enter the diagnostic mode.



e.
E384441

Select "Steering Angle Setting" from the Mode Setting(*) screen to display the Signal Check(*) screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



f.
E435680

Select "Next" from the Signal Check(*) screen to display the Steering Angle Setting D (*) screen.

NOTICE:
·

If "CHK" (red) is displayed for an item on the Signal Check(*) screen, selecting "Next" will not change to the Steering Angle Setting D (*) screen.

·

Check the Signal Check(*) screen when "CHK" (red) is displayed for an item on the Signal Check(*) screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.




g.

Adjust the steering angle

i.
E432772

Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "Steering Center Memorize".


ii.

After selecting "Steering Center Memorize", turn the steering angle fully to the left and fully to the right, and then select "Max Steering Angle Memorize". (Turning right and then left is OK)


iii.

When "Max Steering Angle Memorize" is selected, the steering angle setting values (steering neutral point and maximum steering angle) are stored and the system beeps for a long duration to notify the user that storing is complete before the Mode Setting(*) screen is displayed again.

HINT:
·

A long beep will sound to confirm that the adjustment values have been stored.

·

When all signals are input normally, the Mode Setting(*) screen is displayed automatically after the maximum steering angle is stored.

·

When Steering Angle Setting is incomplete, "OK" is disabled.

·

Even if no DTC is output, a steering sensor malfunction may disable the use of "Max Steering Angle Memorize".

·

If selecting "Max Steering Angle Memorize" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL






i.

Confirm steering angle adjustment.

HINT:

After performing Steering Angle Setting, cancel diagnostic mode and perform Steering Angle Setting Check on the rear view screen.



j.

Check on the rear view screen that the displayed estimated course lines move in synchronization with the steering wheel movements when the steering wheel is turned fully left or right.

HINT:

If the estimated course line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform adjustment again.




PROCEDURE 10: REAR TELEVISION CAMERA VIEW ADJUSTMENT (for REAR CAMERA DETECTION FUNCTION)


HINT:
·

Be sure to check for DTCs before performing this procedure.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.
E386357C01
1.708,0.49 1.958,0.24 1.958,0.24 2.125,0.24 true 1.99,0.719 2.24,0.469 2.24,0.469 2.406,0.469 true 0.917,2.417 1.115,2.417 1.115,2.417 1.677,2.229 true 0.667,2.615 0.865,2.615 0.865,2.615 1.052,2.729 true 2.208,0.156 2.521,0.354 0.313,0.198 10 false *a 2.479,0.375 2.792,0.573 0.313,0.198 10 false *b 0.469,0.698 0.781,0.896 0.313,0.198 10 false *c 0.719,2.323 1.031,2.521 0.313,0.198 10 false *d 0.479,2.521 0.771,2.76 0.292,0.24 10 false *e 1.635,3.031 1.927,3.271 0.292,0.24 10 false *f 2.76,2.406 3.052,2.646 0.292,0.24 10 false *g
*a Vehicle Center
*b Vehicle
*c Front
*d Vehicle End
*e Target Bar for Back Camera Adjustment
*f 1995 to 2005 mm (6.54 to 6.58 ft.)
*g A


Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.


ii.

Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).

HINT:

Create a target bar for adjustment only when adjusting the optical axis of the rear television camera assembly.


Dimension:
Area Specification
A 1000 mm (3.28 ft.)


HINT:
·

Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 100 mm (0.33 ft.) and 1995 to 2005 mm (6.54 to 6.58 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.

·

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.

·

Check that the luggage compartment door is fully closed.





b.

Start diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

NOTICE:

Adjustment must be performed with the engine running. Therefore, apply the parking brake, depress the brake pedal and move the shift lever to P to ensure that the vehicle does not begin moving unexpectedly.


i.
E422909

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E432763

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.



iii.
E384441

Select "Back Camera Setting" on the "Mode Setting (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E435680

Select "Next" on the "Signal Check (*)" screen.

NOTICE:
·

When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, selecting "Next" will not change the screen to the "Back Camera Position Setting D (*)" screen.

·

When "CHK" (red) is displayed for any items on the "Signal Check (*)" screen, perform inspections using the "Signal Check (*)" screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM





c.
E366770C01
1.698,1.042 1.875,0.729 1.875,0.729 2.125,0.719 false 0.333,1.167 0.969,1.083 true 2.688,1.417 3.104,1.583 true 1.177,1.885 1.177,1.719 true 1.49,1.885 1.49,1.719 true 1.813,1.875 1.813,1.708 true 2.135,1.875 2.135,1.708 true 2.677,0.75 3.094,0.667 true 2.427,1.094 2.615,1.073 2.615,1.073 2.427,1.021 true 2.625,1.073 3.063,1.073 true 2.156,0.635 2.469,0.792 0.313,0.156 10 false *a 0.177,1.125 0.333,1.323 0.156,0.198 10 false A 3.125,0.99 3.281,1.188 0.156,0.198 10 false B 1.125,1.917 1.281,2.115 0.156,0.198 10 false C 1.448,1.917 1.604,2.115 0.156,0.198 10 false D 3.167,0.583 3.323,0.781 0.156,0.198 10 false G 2.104,1.906 2.26,2.104 0.156,0.198 10 false F 1.771,1.917 1.927,2.115 0.156,0.198 10 false E 3.167,1.531 3.323,1.729 0.156,0.198 10 false H
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Both Ends of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform vertical and horizontal position adjustment.

·

Move the circle (A) left, right, up and down by selecting the buttons (C), (D), (E) and (F) so that the left end of Target Bar for Back Camera Position Setting is positioned within the center of the circle (A) (center of the inner red circle).



ii.

Perform roll angle adjustment.

·

Rotate the bar (B) by selecting the buttons (G) or (H) so that the bar (B) becomes parallel to target bar for back camera position setting.



iii.

Select "Next" on the "Back Camera Position Setting D (*)" screen.



d.
E366780C01
1.177,1.854 1.177,1.688 true 1.531,1.865 1.531,1.698 true 1.865,1.854 1.865,1.688 true 2.219,1.865 2.219,1.698 true 2.438,1.042 2.833,0.667 2.833,0.667 3.083,0.667 true 1.458,0.906 1.625,0.906 1.625,0.906 1.74,1.063 true 3.115,0.563 3.427,0.719 0.313,0.156 10 false *a 1.323,0.833 1.542,1.031 0.219,0.198 10 false A 1.125,1.885 1.344,2.083 0.219,0.198 10 false B 1.49,1.896 1.708,2.094 0.219,0.198 10 false C 1.813,1.875 2.031,2.073 0.219,0.198 10 false D 2.188,1.875 2.406,2.073 0.219,0.198 10 false E
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Upper Left Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the adjustment mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the corner of the mark (A) with the upper left corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the upper left corner of the target bar.


E366764C02
5.281,5.5 5.594,5.656 0.313,0.156 10 false *c 3.406,5.479 3.719,5.635 0.313,0.156 10 false *b 2.698,3.167 3.01,3.323 0.313,0.156 10 false *a 4.604,3.167 4.917,3.323 0.313,0.156 10 false *a 6.521,3.135 6.833,3.292 0.313,0.156 10 false *a 0.115,2.406 1.344,2.604 1.229,0.198 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) L_TOP" screen.



e.
E366781C01
2.698,0.885 2.969,0.635 2.969,0.635 3.156,0.635 true 1.219,0.76 1.385,0.76 1.385,0.76 1.698,1.052 true 1.167,1.854 1.167,1.688 true 1.531,1.865 1.531,1.698 true 1.875,1.865 1.875,1.698 true 2.219,1.875 2.219,1.708 true 1.063,0.688 1.198,0.917 0.135,0.229 10 false A 3.177,0.552 3.427,0.719 0.25,0.167 10 false *a 2.177,1.896 2.313,2.125 0.135,0.229 10 false E 1.833,1.906 1.969,2.135 0.135,0.229 10 false D 1.49,1.896 1.625,2.125 0.135,0.229 10 false C 1.125,1.885 1.26,2.115 0.135,0.229 10 false B
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Lower Left Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower left corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the lower left corner of the target bar.


E366765C02
2.677,4.406 2.99,4.563 0.313,0.156 10 false *b 6.51,4.365 6.823,4.521 0.313,0.156 10 false *c 4.635,4.479 4.948,4.635 0.313,0.156 10 false *c 5.594,3.396 5.906,3.552 0.313,0.156 10 false *a 3.667,3.396 3.979,3.552 0.313,0.156 10 false *a 0.104,2.385 1.104,2.75 1,0.365 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) L_BTM" screen.



f.
E366782C01
1.167,1.875 1.167,1.708 true 1.51,1.865 1.51,1.698 true 1.854,1.865 1.854,1.698 true 2.219,1.865 2.219,1.698 true 2.323,0.833 2.156,0.833 2.156,0.833 1.708,1.083 true 0.75,1.021 0.583,0.729 0.583,0.729 0.333,0.729 true 0.177,0.646 0.49,0.802 0.313,0.156 10 false *a 2.385,0.771 2.698,0.927 0.313,0.156 10 false A 1.115,1.906 1.438,2.063 0.323,0.156 10 false B 1.479,1.896 1.792,2.052 0.313,0.156 10 false C 1.823,1.885 2.135,2.052 0.313,0.167 10 false D 2.188,1.896 2.5,2.052 0.313,0.156 10 false E
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Upper Right Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the upper right corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the upper right corner of the target bar.


E366767C02
1.479,3.167 1.792,3.323 0.313,0.156 10 false *a 2.115,5.5 2.427,5.656 0.313,0.156 10 false *b 4.083,5.51 4.396,5.667 0.313,0.156 10 false *c 3.458,3.177 3.771,3.333 0.313,0.156 10 false *a 5.344,3.135 5.656,3.292 0.313,0.156 10 false *a 0.115,2.417 1.052,2.792 0.938,0.375 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) R_TOP" screen.



g.
E366783C01
1.719,1.063 2.146,0.802 2.146,0.802 2.229,0.802 true 0.333,0.656 0.583,0.656 0.583,0.656 0.771,0.896 true 1.177,1.854 1.177,1.677 true 1.521,1.844 1.521,1.677 true 1.865,1.865 1.865,1.698 true 2.208,1.865 2.208,1.698 true 1.146,1.885 1.458,2.042 0.313,0.156 10 false B 0.146,0.573 0.458,0.729 0.313,0.156 10 false *a 1.49,1.896 1.802,2.052 0.313,0.156 10 false C 1.823,1.906 2.135,2.063 0.313,0.156 10 false D 2.177,1.917 2.49,2.073 0.313,0.156 10 false E 2.281,0.719 2.594,0.875 0.313,0.156 10 false A
*a Target Bar for Back Camera Position Setting


Back Camera Position Setting (Lower Right Corner of Target Bar)

HINT:
·

When the luggage compartment door is open, the "You can not calibrate the camera when the door is open. Please close the door." message will be displayed and camera position setting will not be possible.

·

If the "You can not calibrate the camera when the door is open. Please close the door." message is displayed even when the luggage compartment door is closed, perform inspections according to Problem Symptoms Table (When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE



i.

Perform camera optical axis adjustment (high accuracy adjustment).

·

Move the mark (A) using the left, right, down and up buttons (B), (C), (D) and (E) to align the outer corner of the mark (A) with the lower right corner of the target bar.

Standard:

The outer corner of the mark (A) is aligned with the lower right corner of the target bar.


E366766C02
5.094,3.375 5.406,3.531 0.313,0.156 10 false *a 2.073,4.344 2.385,4.5 0.313,0.156 10 false *b 5.969,4.313 6.281,4.469 0.313,0.156 10 false *c 4.063,4.396 4.375,4.552 0.313,0.156 10 false *c 3.167,3.344 3.479,3.5 0.313,0.156 10 false *a 0.104,2.417 0.885,2.75 0.781,0.333 10 false Example:
*a Too Far Inside *b Inner Corner Contacting
*c Too Far Outside - -




ii.

Select "Next" on the "Back Camera Position Setting D (*) R_BTM" screen.



h.
E366771E01
1.875,1.063 2.333,0.75 2.333,0.75 2.5,0.75 false 2.542,0.688 2.729,0.927 0.188,0.24 10 false A

Back Verify Mode

i.

Check that (A) and the target adjustment bar are overlapping.

·

If the lines are not aligned, perform the "Steering Center Memorize" and "Max Steering Angle Memorize" operations.

·

If (A) and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the back camera position setting operation.



ii.

Select "OK" to return to the "Mode Setting (*)" screen and complete the adjustment.

HINT:
·

The update is not completed until "OK" is selected.

·

When "OK" is selected, a beep will sound to confirm that the adjustment values have been stored.

·

The adjustment values are not stored until the beep has sounded.