Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2021.02
RM33C0E _59 Vehicle Exterior _065474 EXTERIOR PANELS / TRIM _0328281 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


PROCEDURE

Hide 52536 1.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B470417C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips as shown in the illustration.


b.
B470415

Install the front bumper side retainer LH with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 52535 2.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52131A 3.INSTALL FRONT BUMPER REINFORCEMENT

a.

Install the front bumper reinforcement with the 6 bolts.

B481987

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.
B481986

Engage the 4 clamps.



d.

Install the headlight assembly RH.

HINT:

Use the same procedure as for the LH side.



Hide 52611 4.INSTALL FRONT BUMPER ENERGY ABSORBER

a.
B489579C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 guides to install the front bumper energy absorber as shown in the illustration.


Hide 53879H 5.INSTALL FRONT FENDER LINER RETAINER

a.
B479551C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the 2 front fender liner retainers as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 47749F 6.INSTALL PIN HOLD CLIP

a.
B610732C02
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws to install the 2 pin hold clips as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



Hide 52713A 7.INSTALL FRONT BUMPER SIDE MOULDING LH (for Mesh Type Radiator Grille)

a.
B604944

Engage the 2 guides and 2 claws.


b.
B604943

Install the front bumper side moulding LH with the 2 clips.


Hide 52712 8.INSTALL FRONT BUMPER SIDE MOULDING RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 53102A 9.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)

a.

Engage the 17 claws.

B607500


b.
B607499

Install the lower radiator grille sub-assembly with the 4 screws.


Hide 53102A 10.INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)

a.

Engage the 6 guides and 24 claws.

B607502


b.
B607501

Install the lower radiator grille sub-assembly with the 4 screws.


Hide 53122G 11.INSTALL LOWER CENTER RADIATOR GRILLE MOULDING (for Mesh Type Radiator Grille)

a.

Engage the guide and 4 claws.

B607498


b.
B607497

Install the lower center radiator grille moulding with the screw.


Hide 52534 12.INSTALL FRONT NO. 2 BUMPER RETAINER BRACKET (for Mesh Type Radiator Grille)

HINT:

When installing the front No. 2 bumper retainer bracket, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new front No. 2 bumper retainer bracket.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B606197C03
0,0 0,0 false
V100155

Double-sided Tape


Engage the claw and attach the double-sided tape to install the front No. 2 bumper retainer bracket.

HINT:

Press the front No. 2 bumper retainer bracket firmly to install it.



Hide 52533 13.INSTALL FRONT NO. 1 BUMPER RETAINER BRACKET (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 53124D 14.INSTALL LOWER RADIATOR GRILLE MOULDING LH (for Mesh Type Radiator Grille)

a.
B607496

Engage the guide and 8 claws.


b.
B607495

Install the lower radiator grille moulding LH with the screw.


Hide 53123C 15.INSTALL LOWER RADIATOR GRILLE MOULDING RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 81482C 16.INSTALL FOG LIGHT COVER LH (for Mesh Type Radiator Grille)

a.
B607494

Engage the 6 claws.


b.
B607493

Install the clip.


c.
B607492

Install the fog light cover LH with the 4 clips.


Hide 81481E 17.INSTALL FOG LIGHT COVER RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52713A 18.INSTALL FRONT BUMPER SIDE MOULDING LH (for Bar Type Radiator Grille)

a.
B607491

Engage the 2 guides and 3 claws.


b.
B607490

Install the front bumper side moulding LH with the 5 screws.


Hide 52712 19.INSTALL FRONT BUMPER SIDE MOULDING RH (for Bar Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 81220 20.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 21.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 53101 22.INSTALL RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)

a.
B607486

Engage the guide and 10 claws.


b.
B607485

Install the radiator grille sub-assembly with the 2 screws.


Hide 53101 23.INSTALL RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)

a.
B607489

Engage the 8 claws


b.
B607488

Install the 10 screws.


c.
B607487

Install the radiator grille sub-assembly with the 2 clips.


Hide 52111F 24.INSTALL FRONT CENTER BUMPER BAR (for Bar Type Radiator Grille)

a.
B607484C01
1.042,0.188 1.354,0.344 0.313,0.156 10 false *a 0.646,0.24 0.958,0.396 0.313,0.156 10 false *b 2.563,0.063 2.875,0.219 0.313,0.156 10 false *a 1.448,0.115 1.76,0.271 0.313,0.156 10 false *b 2.208,0.052 2.521,0.208 0.313,0.156 10 false *b 2.885,0.063 3.198,0.219 0.313,0.156 10 false *b
*a Clip
*b Screw


Install the 4 screws.


b.

Install the front center bumper bar with the 2 clips.


Hide 25.INSTALL FRONT BUMPER UPPER RETAINER

HINT:

Use the same procedure for the RH side and LH side.


a.
B596565

Engage the 2 guides.


b.

Install the front bumper upper retainer with the screw.


Hide 75310A 26.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY

a.
B596564

Engage the guide and 4 claws.


b.
B596563

Install the radiator grille emblem assembly with the screw.


Hide 53395E 27.INSTALL HOOD TO FRONT END PANEL SEAL

HINT:

When installing the hood to front end panel seal, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B607482

Engage the 6 clips.


c.

Remove the release paper from a new hood to front end panel seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B607483C01
0,0 0,0 false
V100155

Double-sided Tape


Engage the guide and attach the double-sided tape as shown in the illustration to install the hood to front end panel seal.

HINT:

Press the hood to front end panel seal firmly to install it.



Hide 52128B 28.INSTALL FRONT BUMPER HOLE COVER LH (for Bar Type Radiator Grille)

a.
B607476C01
2.542,2.865 2.375,2.865 false 2.188,2.781 2.406,2.969 0.219,0.188 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 2 guides and 4 claws to install the front bumper hole cover LH as shown in the illustration.


Hide 52128B 29.INSTALL FRONT BUMPER HOLE COVER LH (for Mesh Type Radiator Grille)

a.
B607478C01
2.656,0.427 2.906,0.427 false 2.938,0.344 3.25,0.542 0.313,0.198 10 false *a
*a Hook
V113147

Install in this Direction


Engage the hook.


b.

Engage the 5 claws to install the front bumper hole cover LH as shown in the illustration.


Hide 52127D 30.INSTALL FRONT BUMPER HOLE COVER RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 31.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

a.

Engage the 7 clamps to install the headlight cleaner hose.

B607507


Hide 85208A 32.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 33.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 85354 34.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)

Hide 85353 35.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)

HINT:

Use the same procedure as for the LH side.


Hide 86790B 36.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Hide 86790B 37.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

Hide 38.INSTALL FRONT BUMPER COVER INSERT (w/ Panoramic View Monitor System)

a.

for Mesh Type Radiator Grille:

i.
B607481

Engage the 2 claws to install the front bumper cover insert.



Hide 52423A 39.INSTALL FRONT BUMPER PAD LH (for Bar Type Radiator Grille)

HINT:

When installing the front bumper pad LH, heat the front bumper cover using a heat light.


Heating Temperature
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.


a.

Clean the front bumper cover surface.

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new front bumper pad LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B608630C02
0.927,0.99 1.229,0.99 true 0.729,0.896 0.938,1.104 0.208,0.208 10 true *a
*a Line


Install the front bumper pad LH as shown in the illustration.

HINT:

Press the front bumper pad LH firmly to install it.



Hide 52422A 40.INSTALL FRONT BUMPER PAD RH (for Bar Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52423A 41.INSTALL FRONT BUMPER PAD LH (for Mesh Type Radiator Grille)

a.
B607480

Engage the guide and 2 claws to install the front bumper pad LH.


Hide 52422A 42.INSTALL FRONT BUMPER PAD RH (for Mesh Type Radiator Grille)

HINT:

Use the same procedure as for the LH side.


Hide 52114A 43.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Bar Type Radiator Grille)

a.
B608148C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration.


b.
B608146

Install the front bumper extension mounting bracket with the 2 screws.


Hide 52114A 44.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Mesh Type Radiator Grille)

a.
B608151C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 guides and 2 claws as shown in the illustration.


b.
B608149

Install the front bumper extension mounting bracket with the 2 screws.


Hide 88211B 45.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)

Hide 82114 46.INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

for Bar Type Radiator Grille:

i.

Engage the 7 clamps to install the No. 4 engine room wire.

B607467



b.

for Mesh Type Radiator Grille:

i.

Engage the 12 clamps to install the No. 4 engine room wire.

B607468



Hide 89347B 47.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 48.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89341L 49.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89347B 50.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 51.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)