Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0328967 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU assembly. The hybrid vehicle control ECU assembly uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the hybrid vehicle control ECU assembly determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the power switch is on (IG) and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU assembly detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

Hybrid vehicle control ECU assembly


Cruise Control

WIRING DIAGRAM

E446907E07
5.563,2.323 6.969,2.917 1.406,0.594 10 false Hybrid Vehicle Control ECU Assembly 3.125,2.479 5.417,2.677 2.292,0.198 10 false Stop Light Switch Assembly 3.583,1.417 3.74,1.615 0.156,0.198 10 false B 3.573,0.917 3.729,1.115 0.156,0.198 10 false B 4.177,0.792 4.333,0.99 0.156,0.198 10 false L 4.177,1.594 4.333,1.792 0.156,0.198 10 false L 3.563,1.927 3.99,2.125 0.427,0.198 10 false GND 2.115,1.563 3.115,1.833 1,0.271 10 false ECU-IG2 NO. 3 2.396,1.073 3.396,1.344 1,0.271 10 false STOP 0.073,0.906 1.76,1.104 1.688,0.198 10 false from Auxiliary Battery 0.083,1.417 1.51,1.792 1.427,0.375 10 false from IG2-NO. 2 Relay 3.385,0.813 3.542,1.01 0.156,0.198 10 false 7 4.333,1.458 4.49,1.656 0.156,0.198 10 false 5 3.385,1.813 3.542,2.01 0.156,0.198 10 false 2 3.375,1.292 3.531,1.49 0.156,0.198 10 false 6 4.333,0.688 4.49,0.885 0.156,0.198 10 false 3 3.135,2.313 3.594,2.531 0.458,0.219 10 false A85 5.323,0.781 5.781,1 0.458,0.219 10 false A28 5.344,0.594 5.563,0.813 0.219,0.219 10 false 15 5.354,1.385 5.688,1.604 0.333,0.219 10 false 28 5.667,0.688 6.125,0.885 0.458,0.198 10 false STP 5.677,1.469 6.135,1.667 0.458,0.198 10 false ST1- 2.563,2.979 3.531,3.177 0.969,0.198 10 false to Each ECU 5.323,1.573 5.656,1.792 0.333,0.219 10 false A29

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
E462804C04
1.479,0.083 1.885,0.323 0.406,0.24 1.302,1.333 1.135,1.885 true 2.292,1.333 2.781,1.594 true 2.063,1.365 2.083,1.875 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.115 1.99,0.333 0.427,0.219 10 false A85 2.844,1.542 3.01,1.708 0.167,0.167 10 false B 0.958,1.917 1.375,2.104 0.417,0.188 10 false GND 2.042,1.906 2.208,2.073 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-7 (B) - Body ground Power switch off 11 to 14 V
A85-6 (B) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the A81 stop light switch assembly connector.


b.

Disconnect the A28 and A29 hybrid vehicle control ECU assembly connectors.


c.

Disconnect each ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-3 (L) - A28-15 (STP) Always Below 1 Ω
A81-5 (L) - A29-28 (ST1-) Always Below 1 Ω
A81-3 (L) or A28-15 (STP) - Body ground Always 10 kΩ or higher
A81-5 (L) or A29-28 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR