Before performing troubleshooting for the road sign assist system, make sure that the pre-collision system and lane tracing assist system are not malfunctioning.
Pre-collision system: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Lane tracing assist system: Click hereEngine / Hybrid System>CRUISE CONTROL>LANE TRACING ASSIST SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the following procedure to troubleshoot the road sign assist system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the power switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, check for DTCs.
If a DTC is output, record the DTC.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
If the Vehicle Control History (RoB) is output, record it.
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) is not output | A |
| Vehicle Control History (RoB) is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using the GTS, clear the DTCs.
Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
Refer to each corresponding DTC for details on the detection conditions.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) is not output | A |
| Vehicle Control History (RoB) is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B