Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _078700 TELEMATICS _0387130 TELEMATICS SYSTEM(for eCall) L

TELEMATICS  TELEMATICS SYSTEM(for eCall)  PRECAUTION  


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the cable is reconnected.

System Name See Procedure
Lane Tracing Assist System (Click here)
Parking Support Brake System
Parking Assist Monitor System
Pre-collision System



COMMUNICATION FUNCTION PAUSING


NOTICE:
·

Before performing inspections or repairs which may cause warning messages to be displayed or DTCs to be stored, such as a simulation test or road test, it is necessary to enter communication function pausing mode so that unnecessary warning messages are not sent to the service center.

·

After completing maintenance work, be sure to cancel the communication function pausing mode.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>UTILITY



HINT:
·

To cancel communication function pausing mode, turn the ignition switch off and ON to display the service mode screen and cancel communication function pausing mode.



a.

Communication function pausing mode

i.

Enter communication function pausing mode (Using the GTS) (Method 1)

1.

Turn the ignition switch off.

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Enter the following menus: Body Electrical / Telematics


Body Electrical > Telematics > Trouble Codes
50001 459

ii.

Enter communication function pausing mode (Method 2)

·

w/ Navigation System:

Enter diagnostic mode of navigation system.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR


·

w/o Navigation System:

Enter diagnostic mode of audio and visual system.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR





STRICT PROHIBITION OF MANUAL EMERGENCY CALL USING EMERGENCY CALL SERVICE


a.

Do not make emergency calls in non-emergency situations. When performing an inspection, use the manual maintenance check.

NOTICE:
·

If the emergency call service is used to connect to the PSAP in a non-emergency situation, an unnecessary workload will be generated at the PSAP. This may cause a delayed response by the PSAP to other emergency calls.

·

If emergency vehicles are dispatched due to an accidental operation of the manual (SOS) switch, you may be charged or punished according to local law.




b.

If the manual (SOS) switch is accidentally operated:

i.

Contact the PSAP to tell them that the call was made by mistake.


ii.

An emergency call cannot be halted or finished from the vehicle. Only the PSAP can halt or finish an emergency call.

HINT:

The emergency call can be canceled by pressing the manual (SOS) switch within 5 seconds after the dial tone begins to sound.



iii.

If the PSAP cannot be informed that the emergency call was made by mistake, the center will report an emergency to authorities, emergency facilities and dealerships in compliance with its agreements. As a result, emergency vehicles may be dispatched.




INSPECTION PROCEDURE FOR TELEMATICS TRANSCEIVER


a.

The telematics transceiver uses electrical waves (LTE [Long Term Evolution]). Radio waves and telephone network line may occasionally be unstable depending on time or location factors. Therefore, as for the connection malfunction, as there is the possibility of a temporary phenomenon due to the condition of electrical waves, it is necessary to determine by comparing with occurrence frequency or cellular phone.


b.

With the exception of replacing the mobilephone battery, the telematics transceiver cannot be disassembled (the telematics transceiver case must not be opened). Replace parts.



PRECAUTIONS FOR EMERGENCY CALL SERVICE


a.

Depending on the troubleshooting procedure, it may be necessary to enter test mode and perform a system check.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>OPERATION CHECK


b.

If any of the following parts are replaced, refer to Initialization of Repair Instruction.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Telematics Transceiver

·

Mobilephone battery



c.

The telematics transceiver functions as the emergency call service device and has the IMEI and ICCID.



PRECAUTION FOR MOBILEPHONE BATTERY


a.

The mobilephone battery (back-up battery) has a service life of not less than 3 years.


b.

The mobilephone battery is a Lithium-ion type battery and can be charged from the telematics transceiver.


c.

When the mobilephone battery needs to be replaced, the manual (SOS) switch indicator (red) will illuminate. The telematics transceiver will also store a Diagnostic Trouble Code (DTC) or vehicle control history (RoB) code.



IF AN EMERGENCY CALL CANNOT BE MADE


a.

The emergency call service may not be available, or the call quality may deteriorate in the following situations. (For details, refer to the terms of service and operation manual for the device.)

Cause Details
Communication is interrupted due to the network used for the emergency call system.*
·

The registered vehicle is located outside the cellular phone service area of the emergency call system.

·

The vehicle is overseas.

·

The vehicle is in a cellular phone service area where communication is not possible, such as an indoor environment, a basement parking area, mountains, tunnels or beside a building.

·

Network availability or the time of use is limited, such as when cellular phone networks or public fixed networks (including junction networks) are extremely busy.

·

Network availability is limited by the communication service provider due to a large-scale disaster.

·

The cellular phone network or public fixed network (including junction networks) service used for the emergency call system is suspended or halted due to accidents, maintenance or construction.


The PSAP system cannot determine the vehicle location.
·

The vehicle is in an area where the Global Navigation Satellite System (GNSS) radio signals cannot be received or where it is difficult for radio waves to penetrate, such as an indoor environment, a basement parking area, mountains, tunnels or beside a building.

·

The vehicle location cannot be determined normally or accurately because the vehicle is in the following areas:

-

Areas that cause a large error in the GNSS location calculation, such as in tunnels or a densely built-up area, or after getting off a ferry.


-

Areas that cause a large error in map matching due to an old map database.


·

The GNSS is malfunctioning.


Others Although a manual call is made, the situation cannot be confirmed because the user cannot respond to questions from the PSAP.

NOTICE:

*: Even when the vehicle is within the cellular phone service area, it may be difficult to make emergency phone calls due to radio wave signal conditions or busy lines. In this case, it may not be possible to access the PSAP. As a result, no calls can be made to ask for rescue in the event of a traffic accident. If emergency calls cannot be made, use a landline telephone or cellular phone.