Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light) › from 2021.02
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0341614 HEADLIGHT ASSEMBLY(for Bulb Type Turn Signal Light) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Bulb Type Turn Signal Light)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81056A 1.REMOVE HEADLIGHT ECU SUB-ASSEMBLY (w/ Automatic Headlight Beam Level Control System)

Hide 81134 2.REMOVE HEADLIGHT GASKET (w/ Automatic Headlight Beam Level Control System)

Hide 81510C 3.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.

w/ Automatic Headlight Beam Level Control System:

i.
E375110C01
0,0 0,0 false
V113147

Disconnect in this Direction


Turn the headlight cord with the front turn signal light bulb as shown in the illustration to disconnect them as a unit.


ii.

Remove the front turn signal light bulb from the headlight cord.



b.

w/o Automatic Headlight Beam Level Control System:

i.
E386177C01
0,0 0,0 false
V113147

Disconnect in this Direction


Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove them as a unit.


ii.

Remove the front turn signal light bulb from the front turn signal light socket.



Hide 81515B 4.REMOVE FRONT TURN SIGNAL LIGHT SOCKET (w/o Automatic Headlight Beam Level Control System)

Hide 81171B 5.REMOVE HEADLIGHT LENS

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E375112

Remove the 8 screws.


b.
E375113

Using a hair dryer, heat the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



c.
E375114

Disengage the 9 claws.


d.

Remove the headlight lens from the headlight housing sub-assembly.

HINT:

If the headlight lens cannot be removed even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens. Be careful not to damage the headlight lens and headlight housing sub-assembly.



Hide 81132B 6.REMOVE HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E375115

Remove the headlight lens gasket from the headlight housing sub-assembly.

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



Hide 81169 7.REMOVE HEADLIGHT REFLECTOR

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight reflector or other components.

·

Do not touch the headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E375120C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the screw.


b.

Disengage the 2 guides to remove the headlight reflector as shown in the illustration.


Hide 8116A 8.REMOVE NO. 1 HEADLIGHT CLEARANCE LED UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 1 headlight clearance LED unit or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the No. 1 headlight clearance LED unit with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 1 headlight clearance LED unit or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E447818

Disconnect the 2 connectors.


b.

Disengage the 2 clamps.


c.
E447819C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 screws.


d.

Disengage the guide to remove the No. 1 headlight clearance LED unit as shown in the illustration.


Hide 81160A 9.REMOVE HEADLIGHT LED UNIT ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight LED unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight LED unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight LED unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E447821

Disengage the 5 clamps.


b.

Disconnect the connector.


c.

Disengage the pivot collar.

E461083C01
0.083,0.094 0.458,0.333 0.375,0.24 12 false *A 3.708,0.094 4.083,0.333 0.375,0.24 12 false *B
*A w/o Automatic Headlight Beam Level Control System *B w/ Automatic Headlight Beam Level Control System



d.
E375127C01
0,0 0,0 false
V113147

Turn in this Direction


While holding the headlight LED unit assembly by hand, turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight LED unit assembly.

HINT:

Make sure to remember the number of aiming screw rotations.



e.
E447823

Disengage the 2 clamps.


f.

Disconnect the connector to remove the headlight LED unit assembly from the headlight housing sub-assembly.


Hide 85967 10.REMOVE LIGHT CONTROL ECU (w/o Automatic Headlight Beam Level Control System)

a.
E386176

Disconnect the connector.


b.

Remove the 2 screws and light control ECU.


Hide 81102 11.REMOVE HEADLIGHT HOUSING SUB-ASSEMBLY (w/ Automatic Headlight Beam Level Control System)

HINT:

As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.


a.
E436648C01
0,0 0,0 false
V113147

Disengage in this Direction


Disengage the grommet as shown in the illustration.


b.

Disengage the 2 clamps.


c.
E447815

Disconnect the connector.


d.

Disengage the 3 clamps to remove the headlight cord from the headlight housing sub-assembly.


e.
E436651

Remove the 3 screws.


f.

Disengage the guide to remove the headlight leveling motor from the headlight housing sub-assembly.


g.
E461077

Remove the 2 screws and bracket C from the headlight housing sub-assembly.


h.
E461078

Remove the 2 screws and bracket D from the headlight housing sub-assembly.


Hide 81102 12.REMOVE HEADLIGHT HOUSING SUB-ASSEMBLY (w/o Automatic Headlight Beam Level Control System)

HINT:

As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.


a.
E461084

Disengage the claw.


b.
E461085C01
0,0 0,0 false
V113147

Disengage in this Direction


Disengage the grommet as shown in the illustration.


c.
E461087

Disengage the 2 clamps to remove the headlight cord from the headlight housing sub-assembly.


d.
E461077

Remove the 2 screws and bracket C from the headlight housing sub-assembly.


e.
E461078

Remove the 2 screws and bracket D from the headlight housing sub-assembly.