Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C060B12  Left Electric Parking Brake Actuator Control Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060B12 Left Electric Parking Brake Actuator Control Circuit Short to Battery
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to +B).

·

Detection Time:

Approximately 1 second


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness and connector

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the combination meter assembly.

PROCEDURE

1.CHECK FOR SHORT TO +B
a.

Turn the power switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the v1 parking brake actuator assembly LH connector.


d.
C401220C78
1.5,0.333 1.917,0.583 0.417,0.25 0.979,2.615 1.427,1.958 true 2.417,2.604 2,1.979 true 0.25,0.229 0.563,0.427 0.313,0.198 10 false *a 1.646,0.365 1.958,0.563 0.313,0.198 10 false v1 0.875,2.667 1.542,2.875 0.667,0.208 10 false LE- 2.354,2.667 3.021,2.875 0.667,0.208 10 false LE+
*a Front view of No. 2 Parking Brake Wire Assembly
(to Parking Brake Actuator Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
v1-2 (LE+) - v1-1 (LE-) Electric parking brake not operating Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

2.CHECK FOR SHORT TO +B
2.CHECK FOR SHORT TO +B
a.

Disconnect the vR2 No. 2 parking brake wire assembly connector.


b.
C446427C18
1.5,0.417 1.917,0.667 0.417,0.25 0.25,0.25 0.583,0.5 0.333,0.25 10 false *a 1.604,0.448 1.906,0.677 0.302,0.229 10 false vR2
*a Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
vR2-2 - vR2-1 Electric parking brake not operating Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

NG

3.CHECK FOR SHORT TO +B
3.CHECK FOR SHORT TO +B
a.

Disconnect the vR2 No. 2 parking brake wire assembly connector.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

C454647C05
1.781,0.417 2.198,0.667 0.417,0.25 5.125,0.417 5.542,0.667 0.417,0.25 2.885,2.208 2.531,1.427 true 2.01,2.208 2.375,1.417 true 1.885,0.448 2.344,0.646 0.458,0.198 10 false A44 5.229,0.448 5.688,0.646 0.458,0.198 10 false vR2 0.479,0.75 0.938,1.031 0.458,0.281 10 false *b 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 4.583,0.75 5.125,0.948 0.542,0.198 10 false *c 2.771,2.25 3.271,2.5 0.5,0.25 10 false MRL- 1.844,2.25 2.344,2.5 0.5,0.25 10 false MRL+
*a Front view of wire harness connector *b (to Parking Brake ECU (Brake Actuator Assembly))
*c (to No. 2 Parking Brake Wire Assembly) - -


Standard Voltage:
Tester Connection Condition Specified Condition
vR2-2 or A44-7 (MRL+) - Body ground Always Below 1 V
vR2-1 or A44-8 (MRL-) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR