Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2021.02
RM33C0E _54 Brake _065446 PARKING BRAKE _0329402 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C123A14  IG1 Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C123A14 IG1 Circuit Short to Ground or Open Both of following conditions are met:
1.

Power switch on (IG)

2.

When hybrid vehicle control ECU assembly communicates with main body ECU (multiplex network body ECU) via CAN communication, IG power supply voltage is not received for approximately 3 seconds.


·

Wire harness and connector

·

Parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the combination meter assembly.

WIRING DIAGRAM

C381928E28
1.375,0.948 2.625,1.24 1.25,0.292 10 false ECU-IG1 NO. 3 3.26,0.667 3.542,0.979 0.281,0.313 10 false 26 3.531,0.792 3.813,1.104 0.281,0.313 10 false IG 4.531,0.781 5.177,1.031 0.646,0.25 10 false EGND 5.021,0.667 5.302,0.979 0.281,0.313 10 false 2 3.417,2.458 3.813,2.708 0.396,0.25 10 false A44 3.417,2.625 5.073,3.073 1.656,0.448 10 false Parking Brake ECU (Brake Actuator Assembly) 1.229,1.802 2.688,2.208 1.458,0.406 10 false to CAN Communication System 0.958,3.24 2.99,3.552 2.031,0.313 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (IG1 VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG1 Voltage IG voltage value Min.: 0.0 V
Max.: 25.5 V
Power switch on (IG): 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
Chassis > Electric Parking Brake > Data List
Tester Display
IG1 Voltage
50003 485 296

Result:
Result Proceed to
The value of IG1 Voltage is between 11 and 14 V A
None of the above conditions are met B



A

2.CLEAR DTC

B

4.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 485

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 485

Result:
Result Proceed to
C123A14 is output A
C123A14 is not output B



A

B

4.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-26 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EGND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EGND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A44 parking brake ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-2 (EGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR