These DTCs are stored when a malfunction occurs in the telephone sub antenna circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B153711 | Telephone Sub Antenna Circuit Short to Ground | Navigation antenna (sub) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Short circuit) |
·
Telematics transceiver ·
Navigation antenna assembly ·
Antenna cord sub-assembly (for Type A) ·
Antenna cord sub-assembly (for Type B) |
| B153713 | Telephone Sub Antenna Circuit Open | Navigation antenna (sub) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON.
(Open circuit) |
·
Telematics transceiver ·
Navigation antenna assembly ·
Antenna cord sub-assembly (for Type A) ·
Antenna cord sub-assembly (for Type B) |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds or more.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type A)) |
Disconnect the F antenna cord sub-assembly (for Type A) connector.
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type A)) |
Disconnect the E antenna cord sub-assembly (for Type A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-4 - E-3 | Always | Below 1 Ω |
| F-4 or E-3 - Body ground | Always | 10 kΩ or higher |
| F-4a - E-3a | Always | Below 1 Ω |
| F-4a or E-3a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type B)) |
Disconnect the D antenna cord sub-assembly (for Type B) connector.
| *a | Component without harness connected (Antenna Cord Sub-assembly (for Type B)) |
Disconnect the A antenna cord sub-assembly (for Type B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-3 - A-1 | Always | Below 1 Ω |
| D-3 or A-1 - Body ground | Always | 10 kΩ or higher |
| D-3a - A-1a | Always | Below 1 Ω |
| D-3a or A-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation antenna assembly with a known good one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT