Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _078700 TELEMATICS _0466484 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157213 Microphone Circuit Open Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telematics transceiver

·

Roof console box sub-assembly

·

Telephone microphone assembly

·

Harness or connector



WIRING DIAGRAM

w/ Sliding Roof
E280570E34
1.115,0.635 1.563,0.896 0.448,0.26 10 false MCVD 1.635,0.635 1.906,0.875 0.271,0.24 10 false 5 1.156,0.958 1.542,1.208 0.385,0.25 10 false MCI+ 1.635,0.958 1.885,1.198 0.25,0.24 10 false 6 1.156,1.271 1.531,1.5 0.375,0.229 10 false MCI- 1.635,1.271 1.969,1.688 0.333,0.417 10 false 7 1.115,1.594 1.594,1.844 0.479,0.25 10 false SGND 1.635,1.594 1.885,1.833 0.25,0.24 10 false 23 3.865,0.635 4.448,0.906 0.583,0.271 10 false MACC 3.677,0.635 3.958,0.865 0.281,0.229 10 false 9 3.865,0.958 4.354,1.188 0.49,0.229 10 false MCO+ 3.688,0.958 3.896,1.188 0.208,0.229 10 false 8 3.865,1.271 4.323,1.5 0.458,0.229 10 false MCO- 2.417,1.625 3.125,1.938 0.708,0.313 10 false (Shielded) 3.677,1.281 3.906,1.5 0.229,0.219 10 false 7 0.198,2.135 0.635,2.375 0.438,0.24 10 false K151 0.198,2.302 2.125,2.552 1.927,0.25 10 false Telematics Transceiver 4.313,2.146 4.656,2.427 0.344,0.281 10 false V14 4.313,2.302 6.448,2.604 2.135,0.302 10 false Roof Console Box Sub-assembly 4.385,1.677 6.469,2.021 2.083,0.344 10 false Telephone Microphone Assembly 4.542,1.5 4.698,1.698 0.156,0.198 10 false A 4.74,0.667 5.323,0.938 0.583,0.271 10 false MACC 4.74,0.979 5.229,1.208 0.49,0.229 10 false MIC+ 4.75,1.302 5.208,1.531 0.458,0.229 10 false MIC- 4.604,0.667 4.833,0.885 0.229,0.219 10 false 5 4.604,0.979 4.833,1.198 0.229,0.219 10 false 3 4.604,1.292 4.833,1.51 0.229,0.219 10 false 2

w/o Sliding Roof
E280570E35
1.115,0.635 1.563,0.896 0.448,0.26 10 false MCVD 1.635,0.635 1.906,0.875 0.271,0.24 10 false 5 1.156,0.958 1.542,1.208 0.385,0.25 10 false MCI+ 1.635,0.958 1.885,1.198 0.25,0.24 10 false 6 1.156,1.271 1.531,1.5 0.375,0.229 10 false MCI- 1.635,1.271 1.969,1.688 0.333,0.417 10 false 7 1.115,1.594 1.594,1.844 0.479,0.25 10 false SGND 1.635,1.594 1.885,1.833 0.25,0.24 10 false 23 3.865,0.635 4.448,0.906 0.583,0.271 10 false MACC 3.677,0.635 3.958,0.865 0.281,0.229 10 false 6 3.865,0.958 4.354,1.188 0.49,0.229 10 false MCO+ 3.677,0.958 3.885,1.188 0.208,0.229 10 false 5 3.865,1.271 4.323,1.5 0.458,0.229 10 false MCO- 2.417,1.625 3.125,1.938 0.708,0.313 10 false (Shielded) 3.677,1.281 3.906,1.5 0.229,0.219 10 false 4 0.198,2.135 0.635,2.375 0.438,0.24 10 false K151 0.198,2.302 2.125,2.552 1.927,0.25 10 false Telematics Transceiver 4.313,2.146 4.656,2.427 0.344,0.281 10 false V18 4.313,2.302 6.448,2.604 2.135,0.302 10 false Roof Console Box Sub-assembly 4.344,1.677 6.427,2.021 2.083,0.344 10 false Telephone Microphone Assembly 4.51,1.49 4.667,1.688 0.156,0.198 10 false A 4.74,0.656 5.323,0.927 0.583,0.271 10 false MACC 4.74,0.979 5.229,1.208 0.49,0.229 10 false MIC+ 4.74,1.302 5.198,1.531 0.458,0.229 10 false MIC- 4.604,0.667 4.813,0.896 0.208,0.229 10 false 5 4.604,0.979 4.813,1.208 0.208,0.229 10 false 3 4.604,1.292 4.813,1.521 0.208,0.229 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CONFIRM MODEL
2.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/ Sliding Roof A
w/o Sliding Roof B




A

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K151 telematics transceiver connector.


b.

Disconnect the V14 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K151-5 (MCVD) - V14-9 (MACC) Always Below 1 Ω
K151-6 (MCI+) - V14-8 (MCO+) Always Below 1 Ω
K151-7 (MCI-) - V14-7 (MCO-) Always Below 1 Ω
K151-23 (SGND) - Body ground Always 10 kΩ or higher
K151-5 (MCVD) or V14-9 (MACC) - Body ground Always 10 kΩ or higher
K151-6 (MCI+) or V14-8 (MCO+) - Body ground Always 10 kΩ or higher
K151-7 (MCI-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEMATICS TRANSCEIVER (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TELEMATICS TRANSCEIVER (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)
a.
E360650C11
1.521,0.406 1.906,0.688 0.385,0.281 1.49,1.802 1.115,0.979 false 1.781,1.802 2.198,0.979 false 0.333,0.302 0.646,0.5 0.313,0.198 10 false *a 1.594,0.469 2.052,0.667 0.458,0.198 10 false V14 0.885,0.813 1.5,1.01 0.615,0.198 10 false MACC 2.073,0.802 2.688,1 0.615,0.198 10 false MCO-
*a Component with harness connected
(Roof Console Box Sub-assembly)


Remove the telephone microphone assembly but do not disconnect the connectors.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V14-9 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
V14-7 (MCO-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

9.REPLACE TELEMATICS TRANSCEIVER
5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.
E462870C01
0.073,0.313 0.417,0.531 0.344,0.219 0.344,2.396 0.698,2.625 0.354,0.229 2.281,2.823 2.49,3.094 true 1.438,2.823 1.25,3.083 true 1.802,0.958 2.292,0.375 true 1.438,0.958 0.938,0.354 true 1.625,0.375 1.625,0.958 true 1.719,2.823 1.719,3.083 true 0.156,0.073 0.469,0.271 0.313,0.198 10 false *a 0.115,0.344 0.417,0.615 0.302,0.271 10 false V14 0.458,2.427 0.667,2.646 0.208,0.219 10 false A 2.542,3.104 2.979,3.313 0.438,0.208 10 false MACC 0.656,0.156 1.302,0.375 0.646,0.219 10 false MACC 2.135,0.167 2.771,0.531 0.635,0.365 10 false MCO- 0.99,3.104 1.469,3.323 0.479,0.219 10 false MIC- 0.188,1.938 0.5,2.135 0.313,0.198 10 false *b 1.438,0.156 2.073,0.521 0.635,0.365 10 false MCO+ 1.604,3.125 2.083,3.344 0.479,0.219 10 false MIC+
*a Component without harness connected
(Roof Console Box Sub-assembly (Wire Harness Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (MACC) - A-5 (MACC) Always Below 1 Ω
8 (MCO+) - A-3 (MIC+) Always Below 1 Ω
7 (MCO-) - A-2 (MIC-) Always Below 1 Ω
9 (MACC) - 8 (MCO+) Always 10 kΩ or higher
9 (MACC) - 7 (MCO-) Always 10 kΩ or higher
8 (MCO+) - 7 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K151 telematics transceiver connector.


b.

Disconnect the V18 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K151-5 (MCVD) - V18-6 (MACC) Always Below 1 Ω
K151-6 (MCI+) - V18-5 (MCO+) Always Below 1 Ω
K151-7 (MCI-) - V18-4 (MCO-) Always Below 1 Ω
K151-23 (SGND) - Body ground Always 10 kΩ or higher
K151-5 (MCVD) or V18-6 (MACC) - Body ground Always 10 kΩ or higher
K151-6 (MCI+) or V18-5 (MCO+) - Body ground Always 10 kΩ or higher
K151-7 (MCI-) or V18-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK TELEMATICS TRANSCEIVER (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TELEMATICS TRANSCEIVER (TELEPHONE MICROPHONE ASSEMBLY POWER SOURCE)
a.
E187122C82
1.469,0.469 1.875,0.76 0.406,0.292 1.656,2.042 1.323,1.229 false 1.917,2.031 2.229,1.24 false 1.552,0.542 2.01,0.74 0.458,0.198 10 false V18 0.177,0.177 0.49,0.375 0.313,0.198 10 false *a 1.125,1.042 1.74,1.24 0.615,0.198 10 false MACC 2.104,1.052 2.719,1.25 0.615,0.198 10 false MCO-
*a Component with harness connected
(Roof Console Box Sub-assembly)


Remove the roof console box sub-assembly but do not disconnect the connectors.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V18-6 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
V18-4 (MCO-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

9.REPLACE TELEMATICS TRANSCEIVER
8.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.
E452633C03
0.198,0.521 0.542,0.74 0.344,0.219 0.344,2.396 0.698,2.625 0.354,0.229 2.281,2.823 2.49,3.094 true 1.438,2.823 1.25,3.083 true 1.969,0.958 2.458,0.375 true 1.615,0.958 1.115,0.354 true 1.802,0.375 1.802,0.958 true 1.719,2.823 1.719,3.083 true 0.156,0.177 0.469,0.375 0.313,0.198 10 false *a 0.26,0.542 0.563,0.813 0.302,0.271 10 false V18 0.458,2.427 0.667,2.646 0.208,0.219 10 false A 2.542,3.104 2.979,3.313 0.438,0.208 10 false MACC 0.802,0.156 1.448,0.375 0.646,0.219 10 false MACC 2.323,0.167 2.958,0.531 0.635,0.365 10 false MCO- 0.99,3.104 1.469,3.323 0.479,0.219 10 false MIC- 0.188,1.938 0.5,2.135 0.313,0.198 10 false *b 1.604,0.156 2.24,0.521 0.635,0.365 10 false MCO+ 1.604,3.125 2.083,3.344 0.479,0.219 10 false MIC+
*a Component without harness connected
(Roof Console Box Sub-assembly (Wire Harness Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (MACC) - A-5 (MACC) Always Below 1 Ω
5 (MCO+) - A-3 (MIC+) Always Below 1 Ω
4 (MCO-) - A-2 (MIC-) Always Below 1 Ω
6 (MACC) - 5 (MCO+) Always 10 kΩ or higher
6 (MACC) - 4 (MCO-) Always 10 kΩ or higher
5 (MCO+) - 4 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

9.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT