Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0468732 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PANORAMIC VIEW MONITOR DIAGNOSIS SYSTEM


a.

For panoramic view monitor system diagnosis, signals received by the television camera controller can be checked, and the panoramic view monitor system can be calibrated, adjusted and checked using the radio and display receiver assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (VIEW ADJUSTMENT)


E393502E01
2.76,0.927 4.25,1.229 1.49,0.302 2.823,0.99 6.031,1.188 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (STEERING ANGLE SETTING)


E393503E01
2.708,0.917 4.177,1.271 1.469,0.354 2.771,0.99 5.979,1.188 3.208,0.198 10 false Start diagnostic mode 6.344,4.906 6.656,5.104 0.313,0.198 10 false or


DIAGNOSIS SCREEN TRANSITION (BACK CAMERA SETTING)


E393504E01
2.698,0.906 4.188,1.25 1.49,0.344 2.75,0.979 5.958,1.177 3.208,0.198 10 false Start diagnostic mode 4.542,5.104 4.854,5.302 0.313,0.198 10 false or

E372772


DIAGNOSIS SCREEN TRANSITION (CAMERA CHECK)


E432424E01
2.76,0.99 5.969,1.188 3.208,0.198 10 false Start diagnostic mode


DIAGNOSIS SCREEN TRANSITION (DIAG CHECK)


E432425E01
2.771,1 5.979,1.198 3.208,0.198 10 false Start diagnostic mode



DIAG CHECK


a.

Start diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

i.
E422909

Select "Function Check/Setting" on the Service Menu screen.


ii.
E432763

Select "Camera Setting" on the Function Check/Setting I screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.



iii.
E403246

Select "Diag Check" on the Mode Setting(*) screen to display the Diag check (*) screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Check diagnosis.

i.

On the Diag check (*) screen, DTCs output when the television camera controller detects a malfunction can be checked.

E376966

Indication Name Measurement Item Note
Present Diag Code Current DTC DTCs output when the television camera controller detects a malfunction
Past Diag Code Past DTC
PID PID table Values based on information displayed on Data List





SIGNAL CHECK (TELEVISION CAMERA CONTROLLER INPUT SIGNAL)


a.

Start diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

i.
E422909

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E432763

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the television camera controller was performed after television camera controller replacement.

Television Camera Controller Initialization Screen Transition
Not performed "Signal Check" screen
Performed "Mode Setting" screen



iii.
E384441

When the screen changes to the "Mode Setting" screen, select "View Adjustment" to display the "Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Signal check

i.
E435680

On the "Signal Check" screen, it is possible to inspect the state of signals sent to the television camera controller and check the settings.

Item Inspection Detail Note
CAN Speed signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
CAMERA SW Panoramic view monitor switch signal input

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, check that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

i.

Check that "OK" (blue) is displayed for "CAN" and select "OK".

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.




d.

CAMERA SW inspection

i.

Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.






CAMERA CHECK


HINT:
·

Use this function when symptoms such as the camera images not being displayed occur.

·

On the DTC screen, the 4 camera images are displayed as one image and the images input to the television camera controller from the cameras can be checked.



a.

Start diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

i.
E422909

Select "Function Check/Setting" on the Service Menu screen to display the Function Check/Setting I screen.


ii.
E432763

Select "Camera Setting" on the Function Check/Setting I screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the television camera controller was performed after television camera controller replacement.

Television Camera Controller Initialization Screen Transition
Not performed Signal Check(*) screen
Performed Mode Setting(*) screen



iii.
E384441

When the screen changes to the "Mode Setting(*)" screen, select "Camera Check" to display the "Camera Check(*)" screen.



b.

Check camera images.

i.
E376965

On the Camera Check(*) screen, the images that are input to the television camera controller from the 4 cameras are displayed on the screen and the camera images can be checked.

Indication Name Measurement Item Indication Name Measurement Item
Front Front television camera assembly Back Rear television camera assembly
Left Side television camera assembly LH Right Side television camera assembly RH





CAMERA DETECTION SETTING


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options.

Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

i.
E422909

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E432763

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the television camera controller was performed after television camera controller replacement.

Television Camera Controller Initialization Screen Transition
Not performed "Signal Check (*)" screen
Performed "Mode Setting (*)" screen




b.

Camera Detection Setting.

i.
E384441

Select "Camera Detection Setting" on the "Mode Setting (*)" screen.


ii.
E366791

Select ON or OFF on the "Camera Detection Setting (*)" screen as necessary.

HINT:

After selecting ON or OFF, return to the "Mode Setting (*)" screen by selecting "OK" or "Back".






RCD MEMORY CLEAR


a.

Start diagnostic mode.

w/ Navigation System: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

i.
E422909

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E432763

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the television camera controller was performed after television camera controller replacement.

Television Camera Controller Initialization Screen Transition
Not performed "Signal Check (*)" screen
Performed "Mode Setting (*)" screen




b.

RCD Memory Clear

i.
E384441

When the screen changes to the "Mode Setting (*)" screen, select "RCD Memory Clear" to select and hold the item for 2 seconds or more.

NOTICE:

Check the blind spot monitor system first before normally the selected "RCD Memory Clear" screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING






CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION