Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0387691 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (A)
·

Open or short in bus main line

·

Open or short in bus branch line

·

Open or short in wire harness connector (No. 5 CAN junction connector)

·

Clearance warning ECU assembly internal malfunction

·

Blind spot monitor sensor LH (A) internal malfunction

·

Blind spot monitor sensor LH (A) power source circuit malfunction

·

Blind spot monitor sensor RH (B) internal malfunction


○
U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (B)
·

Open or short in bus main line

·

Open or short in bus branch line

·

Open or short in wire harness connector (No. 5 CAN junction connector)

·

Clearance warning ECU assembly internal malfunction

·

Blind spot monitor sensor RH (B) internal malfunction

·

Blind spot monitor sensor RH (B) power source circuit malfunction

·

Blind spot monitor sensor LH (A) internal malfunction


○

WIRING DIAGRAM

E454218E02
0.24,0.146 1.573,0.573 1.333,0.427 10 false from IG1-NO. 1 Relay 2.031,0.333 3.031,0.698 1,0.365 10 false ECU-IG1 NO. 4 2.844,1.563 3,1.76 0.156,0.198 10 false 1 2.854,1.125 3.01,1.323 0.156,0.198 10 false 5 2.354,3.896 2.948,4.156 0.594,0.26 10 false CANH 2.854,2.281 3.01,2.479 0.156,0.198 10 false 6 1.771,3.188 3.917,3.906 2.146,0.719 10 false Blind Spot Monitor Sensor LH (A) 1.771,3.031 2.229,3.292 0.458,0.26 10 false W6 5.656,3.156 6.854,3.917 1.198,0.76 10 false Blind Spot Monitor Sensor RH (B) 5.646,3.01 5.99,3.292 0.344,0.281 10 false W5 6.823,1.688 6.979,1.885 0.156,0.198 10 false 5 6.792,2.396 7.031,2.656 0.24,0.26 10 false 10 5.531,1.552 5.688,1.75 0.156,0.198 10 false 1 5.531,2.281 5.688,2.479 0.156,0.198 10 false 6 2.458,1.25 3.052,1.51 0.594,0.26 10 false BLB 1.865,2.573 2.458,2.833 0.594,0.26 10 false BLGD 6.323,2.531 6.917,2.792 0.594,0.26 10 false BRGD 5.719,1.552 6.313,1.813 0.594,0.26 10 false CA2P 6.427,1.802 7.021,2.063 0.594,0.26 10 false BRB 2.385,2.281 2.979,2.542 0.594,0.26 10 false CA2N 5.708,2.281 6.302,2.542 0.594,0.26 10 false CA2N 1.781,4.719 2.25,5.021 0.469,0.302 10 false R39 1.771,4.875 2.99,5.521 1.219,0.646 10 false Clearance Warning ECU Assembly 3.604,4.75 5.906,5.354 2.302,0.604 10 false No. 5 CAN Junction Connector 2.354,4.375 2.948,4.635 0.594,0.26 10 false CANL 2.854,4.24 3.385,4.531 0.531,0.292 10 false 38 2.844,3.771 3.229,4.083 0.385,0.313 10 false 37 3.531,4.344 3.885,4.563 0.354,0.219 10 false R100 3.521,2.385 3.875,2.604 0.354,0.219 10 false R100 3.521,1.667 3.875,1.885 0.354,0.219 10 false R100 4.552,1.677 4.906,1.896 0.354,0.219 10 false R100 4.552,2.385 4.906,2.604 0.354,0.219 10 false R100 3.635,1.469 3.792,1.667 0.156,0.198 10 false 3 4.615,2.177 4.885,2.375 0.271,0.198 10 false 13 4.646,1.479 4.802,1.677 0.156,0.198 10 false 2 3.51,3.875 3.865,4.094 0.354,0.219 10 false R100 3.635,3.677 3.792,3.875 0.156,0.198 10 false 1 3.604,4.156 3.875,4.354 0.271,0.198 10 false 12 2.375,1.573 2.969,1.833 0.594,0.26 10 false CA2P 3.583,2.177 3.854,2.375 0.271,0.198 10 false 14 1.615,2.448 1.833,2.656 0.219,0.208 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for parking support brake system DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
No DTCs are output A
DTC U117787 only is output B
DTC U117887 only is output C
DTC U117787 and U117887 are output D



A

B

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - BODY GROUND)

C

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - BODY GROUND)

D

6.CHECK CAN BUS (CONFIRM PROBLEM SYMPTOMS)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - BODY GROUND)
a.
E435677C34
1.5,0.25 1.958,0.51 0.458,0.26 2.021,1.375 2.594,1.854 true 1.625,0.302 1.979,0.51 0.354,0.208 10 false W6 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.656,1.792 3.156,1.99 0.5,0.198 10 false BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A))


Disconnect the connector of the blind spot monitor sensor LH (A).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - POWER SOURCE)
a.
E435677C35
1.5,0.25 1.958,0.5 0.458,0.25 2.042,1.146 2.563,0.615 true 1.625,0.292 1.979,0.5 0.354,0.208 10 false W6 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.646,0.552 3.146,0.75 0.5,0.198 10 false BLB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A))


Disconnect the connector of the blind spot monitor sensor LH (A).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W6-5 (BLB) - Body ground Ignition Switch ON 11 to 14 V
W6-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - BODY GROUND)
a.
E435677C36
1.5,0.333 2,0.583 0.5,0.25 2.573,1.865 2.01,1.385 true 1.656,0.375 2.01,0.583 0.354,0.208 10 false W5 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.667,1.781 3.167,1.979 0.5,0.198 10 false BRGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B))


Disconnect the connector of the blind spot monitor sensor RH (B).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - POWER SOURCE)
a.
E435677C54
1.5,0.302 1.958,0.552 0.458,0.25 2.552,0.635 2.302,0.635 2.302,0.635 2.01,1.167 true 1.615,0.344 1.969,0.552 0.354,0.208 10 false W5 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.635,0.552 3.135,0.75 0.5,0.198 10 false BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B))


Disconnect the connector of the blind spot monitor sensor RH (B).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W5-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
W5-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CAN BUS (CONFIRM PROBLEM SYMPTOMS)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
E401715C19
1.458,2.823 1.865,3.073 0.406,0.25 1.479,0.521 1.885,0.771 0.406,0.25 2.354,3.792 2.844,3.521 true 1,1.458 1.49,2.542 true 0.885,1.469 0.74,2.323 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 1.417,2.573 2.031,2.771 0.615,0.198 10 false CANH 0.51,2.375 1.125,2.573 0.615,0.198 10 false CANL 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.5,2.854 1.958,3.052 0.458,0.198 10 false K154 1.552,0.542 2.01,0.74 0.458,0.198 10 false R39
*a Component with wire harness connected
(Clearance Warning ECU Assembly)
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Problem Symptom if Specified Condition Not Met
R39-37 (CANH) - R39-38 (CANL) Disconnect cable from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short in line
70 Ω or higher: Open in main line
R39-37 (CANH) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Short to ground
R39-38 (CANL) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Short to ground
R39-37 (CANH) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: Short to +B
R39-38 (CANL) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: Short to +B



Result:
Result Proceed to
OK A
NG (open in main line) B
NG (short in line) C
NG (short to +B or ground) D



A

7.CLEAR DTCS

B

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)

C

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)

D

17.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR LH (A) CONNECTION MAIN LINE)
7.CLEAR DTCS
a.

Using the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 and U117887 are output A
DTC U117787 and U117887 are not output B



A

B

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction connector.

E429360C08
3.177,0.396 3.583,0.646 0.406,0.25 2.896,1.438 2.688,0.469 true 2.896,1.771 2.76,2.24 true 2.698,1.781 2.125,2.26 true 2.531,1.771 1.521,2.042 true 1.51,1.302 2.521,1.49 true 2.719,1.438 2.344,0.635 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.958,1.219 1.625,1.458 0.667,0.24 10 false CANH*b 2.396,2.271 3.063,2.51 0.667,0.24 10 false CANL*d 2.417,0.24 3.083,0.479 0.667,0.24 10 false CANH*d 1.844,2.271 2.51,2.51 0.667,0.24 10 false CANL*c 1,1.99 1.667,2.229 0.667,0.24 10 false CANL*b 2.052,0.469 2.719,0.708 0.667,0.24 10 false CANH*c 3.219,0.427 3.719,0.667 0.5,0.24 10 false R100
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire
*c to Blind Spot Monitor Sensor RH (B) CAN Main Wire *d to Blind Spot Monitor Sensor LH (A) CAN Main Wire



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-1 (CANH) - R100-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R100-2 (CANH) - R100-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R100-3 (CANH) - R100-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (A) CAN main wire) B
NG (to blind spot monitor sensor RH (B) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (A))

C

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (B))

D

12.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (A))
a.
E435677C38
1.51,0.302 1.969,0.552 0.458,0.25 0.823,1.833 1.323,1.365 true 0.792,0.74 1.333,1.167 true 1.615,0.344 1.969,0.552 0.354,0.208 10 false W6 0.375,0.594 0.875,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.427,1.781 0.927,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A))


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the W6 blind spot monitor sensor LH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - W6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - NO. 5 CAN JUNCTION CONNECTOR)

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (B))
a.
E435677C39
1.51,0.302 1.958,0.552 0.448,0.25 1.365,1.125 0.802,0.698 true 1.344,1.375 0.875,1.833 true 1.615,0.344 1.969,0.552 0.354,0.208 10 false W5 0.396,0.594 0.896,0.792 0.5,0.198 10 false CA2P 0.135,0.094 0.635,0.292 0.5,0.198 10 false *a 0.458,1.781 0.958,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B))


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the W5 blind spot monitor sensor RH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - NO. 5 CAN JUNCTION CONNECTOR)

12.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.
C440681C07
1.5,0.5 1.917,0.75 0.417,0.25 2.271,2.385 2.708,1.823 true 2.375,2.615 2.844,1.833 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,2.344 2.24,2.531 0.406,0.188 10 false CANH 1.594,0.542 1.906,0.74 0.313,0.198 10 false R39 2.031,2.635 2.438,2.823 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Reconnect the No. 5 CAN junction connector.


b.

Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37 (CANH) - R39-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction connector.

E429360C08
3.177,0.396 3.583,0.646 0.406,0.25 2.896,1.438 2.688,0.469 true 2.896,1.771 2.76,2.24 true 2.698,1.781 2.125,2.26 true 2.531,1.771 1.521,2.042 true 1.51,1.302 2.521,1.49 true 2.719,1.438 2.344,0.635 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.958,1.219 1.625,1.458 0.667,0.24 10 false CANH*b 2.396,2.271 3.063,2.51 0.667,0.24 10 false CANL*d 2.417,0.24 3.083,0.479 0.667,0.24 10 false CANH*d 1.844,2.271 2.51,2.51 0.667,0.24 10 false CANL*c 1,1.99 1.667,2.229 0.667,0.24 10 false CANL*b 2.052,0.469 2.719,0.708 0.667,0.24 10 false CANH*c 3.219,0.427 3.719,0.667 0.5,0.24 10 false R100
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire
*c to Blind Spot Monitor Sensor RH (B) CAN Main Wire *d to Blind Spot Monitor Sensor LH (A) CAN Main Wire



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-1 (CANH) - R100-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R100-2 (CANH) - R100-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R100-3 (CANH) - R100-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (A) CAN main wire) B
NG (to blind spot monitor sensor RH (B) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (A))

C

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (B))

D

16.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (A))
a.
E435677C40
1.51,0.302 1.917,0.552 0.406,0.25 0.927,1.792 1.344,1.375 true 0.802,0.698 1.333,1.167 true 1.604,0.354 1.958,0.563 0.354,0.208 10 false W6 0.375,0.594 0.875,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.427,1.781 0.927,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A))


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the W6 blind spot monitor sensor LH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - W6-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - NO. 5 CAN JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (B))
a.
E435677C41
1.51,0.302 1.969,0.552 0.458,0.25 1.323,1.125 0.813,0.74 true 1.323,1.365 0.854,1.781 true 1.646,0.344 2,0.552 0.354,0.208 10 false W5 0.396,0.594 0.896,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.458,1.781 0.958,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B))


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the W5 blind spot monitor sensor RH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - W5-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - NO. 5 CAN JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
C440681C08
1.5,0.5 1.917,0.75 0.417,0.25 2.26,2.427 2.729,1.833 true 2.438,2.688 2.833,1.844 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,2.344 2.24,2.531 0.406,0.188 10 false CANH 1.594,0.542 1.906,0.74 0.313,0.198 10 false R39 2.031,2.635 2.438,2.823 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Reconnect the No. 5 CAN junction connector.


b.

Disconnect the R39 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37 (CANH) - R39-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR LH (A) CONNECTION MAIN LINE)
a.

Disconnect the No. 5 CAN junction connector.

C407343C74
1.563,0.5 2.063,0.75 0.5,0.25 4.979,0.458 5.479,0.708 0.5,0.25 1.313,2.125 1.5,1.635 true 1.01,0.719 1.5,1.385 true 6.177,2.073 5.854,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.688,0.542 2.188,0.781 0.5,0.24 10 false R100 0.615,0.594 1.281,0.833 0.667,0.24 10 false CANH 1.271,2.156 1.938,2.396 0.667,0.24 10 false CANL 5.042,0.51 5.542,0.75 0.5,0.24 10 false K154 6.219,2.125 6.885,2.365 0.667,0.24 10 false BAT 3.813,0.115 4.125,0.313 0.313,0.198 10 false *1
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*1 DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-3 (CANH) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R100-14 (CANL) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R100-3 (CANH) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher
R100-14 (CANL) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG



OK

18.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR RH (B) CONNECTION MAIN LINE)

NG

22.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR LH (A))
18.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR RH (B) CONNECTION MAIN LINE)
a.

Disconnect the No. 5 CAN junction connector.

C407343C75
1.563,0.5 2.063,0.75 0.5,0.25 4.979,0.458 5.406,0.708 0.427,0.25 0.865,2.094 1.365,1.646 true 0.792,0.635 1.365,1.375 true 6.177,2.073 5.854,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.667,0.542 2.167,0.781 0.5,0.24 10 false R100 0.365,0.552 1.031,0.792 0.667,0.24 10 false CANH 0.458,2.104 1.125,2.344 0.667,0.24 10 false CANL 5.031,0.51 5.531,0.75 0.5,0.24 10 false K154 6.219,2.125 6.885,2.365 0.667,0.24 10 false BAT 3.813,0.115 4.125,0.313 0.313,0.198 10 false *1
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*1 DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-2 (CANH) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R100-13 (CANL) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R100-2 (CANH) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher
R100-13 (CANL) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG



OK

19.CHECK FOR SHORT IN CAN BUS (CLEARANCE WARNING ECU ASSEMBLY CONNECTION BRANCH LINE)

NG

21.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR RH (B))
19.CHECK FOR SHORT IN CAN BUS (CLEARANCE WARNING ECU ASSEMBLY CONNECTION BRANCH LINE)
a.

Reconnect the No. 5 CAN junction connector.

C407343C76
1.563,0.5 2.063,0.75 0.5,0.25 4.979,0.458 5.427,0.708 0.448,0.25 0.865,2.104 1.229,1.656 true 0.823,0.625 1.229,1.396 true 6.177,2.073 5.854,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.656,0.542 2.156,0.781 0.5,0.24 10 false R100 0.365,0.552 1.031,0.792 0.667,0.24 10 false CANH 0.458,2.104 1.125,2.344 0.667,0.24 10 false CANL 5.042,0.5 5.542,0.74 0.5,0.24 10 false K154 6.219,2.125 6.885,2.365 0.667,0.24 10 false BAT 3.667,0.052 3.979,0.25 0.313,0.198 10 false *1
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*1 DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R100-1 (CANH) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R100-12 (CANL) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R100-1 (CANH) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher
R100-12 (CANL) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 5 CAN JUNCTION CONNECTOR

NG

20.CHECK FOR SHORT IN CAN BUS (CLEARANCE WARNING ECU ASSEMBLY)
20.CHECK FOR SHORT IN CAN BUS (CLEARANCE WARNING ECU ASSEMBLY)
a.
E401717C17
1.458,2.823 1.865,3.073 0.406,0.25 1.479,0.521 1.885,0.771 0.406,0.25 2.354,3.792 2.844,3.521 true 2.625,1.427 3.115,2.51 true 2.521,1.406 2.375,2.26 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 2.188,2.323 2.802,2.521 0.615,0.198 10 false CANH 2.979,2.552 3.427,2.75 0.448,0.198 10 false CANL 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.51,2.875 1.969,3.073 0.458,0.198 10 false K154 1.552,0.542 2.01,0.74 0.458,0.198 10 false R39
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*1 DLC3


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the connector of the clearance warning ECU assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R39-37 (CANH) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R39-38 (CANL) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
R39-37 (CANH) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher
R39-38 (CANL) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 5 CAN JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR RH (B))
a.
E401716C34
1.458,2.823 1.865,3.073 0.406,0.25 1.406,0.406 1.813,0.656 0.406,0.25 2.354,3.792 2.844,3.521 true 1.229,1.5 0.698,2.135 true 1.24,1.354 0.74,0.917 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 0.25,2.094 0.865,2.292 0.615,0.198 10 false CA2N 0.26,0.833 0.875,1.031 0.615,0.198 10 false CA2P 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.51,2.875 1.969,3.073 0.458,0.198 10 false K154 1.49,0.438 1.948,0.635 0.458,0.198 10 false W5
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B))
*1 DLC3


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the connector of the blind spot monitor sensor RH (B).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W5-1 (CA2P) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
W5-6 (CA2N) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
W5-1 (CA2P) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher
W5-6 (CA2N) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (B) - NO. 5 CAN JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN CAN BUS (BLIND SPOT MONITOR SENSOR LH (A))
a.
E401716C35
1.458,2.823 1.865,3.073 0.406,0.25 1.406,0.406 1.813,0.656 0.406,0.25 2.354,3.792 2.844,3.521 true 1.229,1.5 0.698,2.135 true 1.24,1.354 0.74,0.917 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 0.25,2.094 0.865,2.292 0.615,0.198 10 false CA2N 0.26,0.833 0.875,1.031 0.615,0.198 10 false CA2P 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.51,2.865 1.969,3.063 0.458,0.198 10 false K154 1.49,0.438 1.948,0.635 0.458,0.198 10 false W6
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A))
*1 DLC3


Reconnect the R100 No. 5 CAN junction connector.


b.

Disconnect the connector of the blind spot monitor sensor LH (A).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-1 (CA2P) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
W6-6 (CA2N) - Body ground Disconnect cable from negative (-) battery terminal 200 Ω or higher
W6-1 (CA2P) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher
W6-6 (CA2N) - K154-16 (BAT) Disconnect cable from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (A) - NO. 5 CAN JUNCTION CONNECTOR)