Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING ECU (for LHD) › from 2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0334375 CLEARANCE WARNING ECU(for LHD) A

PARK ASSIST / MONITORING  CLEARANCE WARNING ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during clearance warning ECU assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
w/o Parking Support Brake System

Clearance warning ECU assembly


Register bumper type TOYOTA Parking Assist-sensor System (Click here)
w/ Parking Support Brake System

Clearance warning ECU assembly


·

Measure ultrasonic sensor detection angle

·

Steering angle zero point learning

·

Register bumper type

·

Register ultrasonic sensor detection angle


·

TOYOTA Parking Assist-sensor System

·

Parking Support Brake System


(Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an airbag deploys for any reason, it may cause a serious injury.



Hide 55435B 4.REMOVE NO. 1 METER HOOD CLUSTER

Hide 55012A 5.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55476C 6.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH

Hide 67913 7.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 8.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 9.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 55317A 10.REMOVE INSTRUMENT SIDE PANEL RH

Hide 55607 11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 73990 12.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 55303B 13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Passenger Side Knee Airbag)

Hide 55303B 14.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 82877 15.REMOVE ECU INTEGRATION BOX RH

Hide 89340A 16.REMOVE CLEARANCE WARNING ECU ASSEMBLY

a.
E371960C01
1.375,3.094 1.615,2.365 true 1.271,3.094 1.583,3.25 0.313,0.156 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the clearance warning ECU assembly as shown in the illustration.

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the claw more than necessary.