Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD) › from 2021.02
RM33C0E _54 Brake _065443 BRAKE SYSTEM (OTHER) _0319353 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)

CAUTION / NOTICE / HINT

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide 55708 3.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 4.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 12601B 5.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 6.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 44572C 7.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C378044

Slide the clip and disconnect the No. 2 brake actuator hose from the No. 1 brake actuator tube.


Hide 473A1 8.DISCONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C378046

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.




Hide 47070 9.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C377744C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C378048

Disengage the claw and clamp to separate the brake booster pump assembly wire harness from the brake actuator bracket assembly.


c.
C381027

Remove the nut from the brake booster pump assembly.


d.
C378049C01
0.656,3.156 1.01,3.156 false 0.583,3.75 0.938,3.75 false 2.375,3.99 2.729,3.99 false 1.125,4.354 1.125,4.063 false 2.75,3.906 3.063,4.063 0.313,0.156 10 false *a 0.5,3.083 0.813,3.24 0.313,0.156 10 false *b 0.438,3.677 0.75,3.833 0.313,0.156 10 false *c 1.063,4.365 1.375,4.521 0.313,0.156 10 false *d
*a Union
*b Connector
*c Wire Harness
*d Stud
V113147

Remove in this Direction


Remove the brake booster pump assembly, brake booster pump bushing and brake actuator case collar from the brake actuator bracket assembly as shown in the illustration.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.




e.
C380676

Remove the 2 brake booster pump collars and 2 brake booster pump bushings from the brake booster pump assembly.

HINT:

Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.



Hide 44572C 10.REMOVE NO. 2 BRAKE ACTUATOR HOSE

a.
C378052

Slide the clip and remove the No. 2 brake actuator hose from the brake booster pump assembly.