Home › General › MAINTENANCE › REAR DISC BRAKE PAD › from 2021.02
RM33C0E _V1 General _065432 MAINTENANCE _0328019 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>PRECAUTION



Hide 2.REMOVE REAR WHEEL

Hide 3.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 4.DISABLE BRAKE CONTROL

Hide 890C0A 5.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 04466 6.REMOVE REAR DISC BRAKE PAD

CAUTION:
C379268

·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when removing the rear disc brake pads.

·

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C379267C02
2.594,2.365 2.906,2.521 0.313,0.156 10 false *a 2.375,1.146 2.688,1.302 0.313,0.156 10 false *b
*a Hold
*b Turn


Hold the rear No. 1 disc brake cylinder slide pin and remove the bolt.


b.

Pull the rear disc brake cylinder assembly upward.


c.
C379269

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 7.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C371419C03
0.49,1.594 0.49,1.177 false 0.979,1.781 0.979,1.365 false 1.844,2.833 1.844,2.531 false 2.51,3.146 2.51,2.938 false 3.052,2.896 3.052,2.594 false 0.896,1.792 1.208,1.948 0.313,0.156 10 false *1 0.417,1.615 0.688,1.813 0.271,0.198 10 false *2 1.76,2.854 2.073,3.01 0.313,0.156 10 false *4 2.427,3.167 2.74,3.323 0.313,0.156 10 false *4 2.979,2.906 3.292,3.063 0.313,0.156 10 false *3
*1 Rear No. 1 Disc Brake Anti-squeal Shim
*2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Anti-squeal Shim
*4 Rear Disc Brake Pad Wear Indicator Plate


Remove the rear No. 2 disc brake anti-squeal shim from the rear disc brake pad (inside).


b.

Remove the rear No. 1 disc brake anti-squeal shim from the rear disc brake pad (inside).


c.

Remove the rear disc brake anti-squeal shim from the rear disc brake pad (outside).


d.
C366017

Remove the rear disc brake pad wear indicator plate from each rear disc brake pad.