Home › Brake › BRAKE (REAR) › REAR BRAKE › from 2021.02
RM33C0E _54 Brake _065445 BRAKE (REAR) _0332046 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>PRECAUTION



Hide 2.REMOVE REAR WHEEL

Hide 3.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 4.DISABLE BRAKE CONTROL

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:
·

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.

·

Do not operate the electric parking brake switch assembly when the electric parking brake system is in rear brake pad replacement mode.




b.
C346768

Disconnect the reservoir level switch connector.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL


d.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


e.

Check that the brake pedal cannot be further depressed.


Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 6.SEPARATE REAR FLEXIBLE HOSE

a.
C371414

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 890C0A 7.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 46310B 8.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

Hide 47850 9.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C371417C02
2.542,1.156 2.854,1.313 0.313,0.156 10 false *a 2.719,2.49 3.031,2.646 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 04466 10.REMOVE REAR DISC BRAKE PAD

a.
C371418

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 11.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 12.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C371420

Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 13.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C371421C02
2.167,0.365 2.552,0.365 true 1.958,1.677 2.344,1.677 true 2.385,1.604 2.615,1.781 0.229,0.177 10 true *1 2.583,0.281 2.896,0.438 0.313,0.156 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


b.
C336764C01
1.979,1.25 2.271,0.969 2.271,0.969 2.573,0.969 false 2.615,0.875 2.927,1.031 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 2 disc brake cylinder slide pin.



Hide 47775D 14.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C371422

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 47822 15.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C371423

Remove the 2 bolts and rear disc brake cylinder mounting.


Hide 42431 16.REMOVE REAR DISC

a.
C371424C02
1.542,1.458 0.844,1.906 0.844,1.906 1.5,1.406 false 0.635,1.854 0.948,2.01 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc.