Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY (for Front Passenger Side) › from 2021.02
RM33C0E _58 Vehicle Interior _065460 SUPPLEMENTAL RESTRAINT SYSTEMS _0331862 KNEE AIRBAG ASSEMBLY(for Front Passenger Side) A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY(for Front Passenger Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower No. 2 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane tracing assist system (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67913 4.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 5.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the instrument side panel RH.


Hide 55317A 7.REMOVE INSTRUMENT SIDE PANEL RH

Hide 55607 8.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55435B 9.REMOVE NO. 1 METER HOOD CLUSTER

Hide 55012A 10.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55476C 11.REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH

Hide 73990 12.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B471919

Remove the 3 bolts.


d.
B471920

Disengage the 3 claws to separate the lower No. 2 instrument panel airbag assembly.

NOTICE:

When separating the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.



e.
B471921C01
1.531,1.26 2.167,1.26 true 2.323,1.167 2.771,1.167 true 1.073,2.823 1.25,3.125 1.25,3.125 1.51,3.125 true 2.802,1.073 3.01,1.292 0.208,0.219 10 true *a 1.333,1.177 1.552,1.385 0.219,0.208 10 true *b 1.542,3.031 1.719,3.229 0.177,0.198 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Locking Button
V113147

Release in this Direction


Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.


f.

Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.