The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (driver door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (driver door) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (driver door), to adjust the mirror surface position.
for LHD
for RHD
The power mirror control system (w/ Memory) uses the CAN communication system and LIN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Selection SW (R) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off
ON: Mirror select switch R switch on |
- |
| Mirror Selection SW (L) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off
ON: Mirror select switch L switch on |
- |
| Mirror Position SW (R) | Mirror adjust switch signal (Right) | OFF or ON | OFF: Mirror adjust switch not pushed right
ON: Mirror adjust switch pushed right |
Check with the mirror select switch L or R selected |
| Mirror Position SW (L) | Mirror adjust switch signal (Left) | OFF or ON | OFF: Mirror adjust switch not pushed left
ON: Mirror adjust switch pushed left |
Check with the mirror select switch L or R selected |
| Mirror Position SW (Up) | Mirror adjust switch signal (Up) | OFF or ON | OFF: Mirror adjust switch not pushed up
ON: Mirror adjust switch pushed up |
Check with the mirror select switch L or R selected |
| Mirror Position SW (Dwn) | Mirror adjust switch signal (Down) | OFF or ON | OFF: Mirror adjust switch not pushed down
ON: Mirror adjust switch pushed down |
Check with the mirror select switch L or R selected |
| Tester Display |
|---|
| Mirror Selection SW (R) |
| Mirror Selection SW (L) |
| Mirror Position SW (R) |
| Mirror Position SW (L) |
| Mirror Position SW (Up) |
| Mirror Position SW (Dwn) |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly (driver door).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly (driver door) (mirror surface).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:
Disconnect the O21*1 or O22*2 outer rear view mirror assembly (driver door).
*1: for 16 Pin Connector
*2: for 22 Pin Connector
Disconnect the O9 outer mirror control ECU assembly (driver door).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O21-1 (MV) - O9-1 (LMVR) | Always | Below 1 Ω |
| O21-9 (MH) - O9-9 (LMHR) | Always | Below 1 Ω |
| O21-10 (M+) - O9-10 (LM+R) | Always | Below 1 Ω |
| O21-1 (MV) or O9-1 (LMVR) - Body ground | Always | 10 kΩ or higher |
| O21-9 (MH) or O9-9 (LMHR) - Body ground | Always | 10 kΩ or higher |
| O21-10 (M+) or O9-10 (LM+R) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O22-7 (MV) - O9-1 (LMVR) | Always | Below 1 Ω |
| O22-9 (MH) - O9-9 (LMHR) | Always | Below 1 Ω |
| O22-8 (M+) - O9-10 (LM+R) | Always | Below 1 Ω |
| O22-7 (MV) or O9-1 (LMVR) - Body ground | Always | 10 kΩ or higher |
| O22-9 (MH) or O9-9 (LMHR) - Body ground | Always | 10 kΩ or higher |
| O22-8 (M+) or O9-10 (LM+R) - Body ground | Always | 10 kΩ or higher |
for RHD:
Disconnect the N24 outer rear view mirror assembly (driver door).
Disconnect the N10 outer mirror control ECU assembly (driver door).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-7 (MV) - N10-1 (RMVR) | Always | Below 1 Ω |
| N24-9 (MH) - N10-9 (RMHR) | Always | Below 1 Ω |
| N24-8 (M+) - N10-10 (RM+R) | Always | Below 1 Ω |
| N24-7 (MV) or N10-1 (RMVR) - Body ground | Always | 10 kΩ or higher |
| N24-9 (MH) or N10-9 (RMHR) - Body ground | Always | 10 kΩ or higher |
| N24-8 (M+) or N10-10 (RM+R) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL
Inspect the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O25*1 or N25*2 outer mirror switch assembly.
*1: for LHD
*2: for RHD
Disconnect the K53 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O25-7 (E) - K53-9 (MIRE) | Always | Below 1 Ω |
| O25-4 (M+) - K53-7 (MIRB) | Always | Below 1 Ω |
| O25-5 (MSW) - K53-8 (MIRS) | Always | Below 1 Ω |
| O25-7 (E) or K53-9 (MIRE) - Body ground | Always | 10 kΩ or higher |
| O25-4 (M+) or K53-7 (MIRB) - Body ground | Always | 10 kΩ or higher |
| O25-5 (MSW) or K53-8 (MIRS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N25-7 (E) - K53-9 (MIRE) | Always | Below 1 Ω |
| N25-4 (M+) - K53-7 (MIRB) | Always | Below 1 Ω |
| N25-5 (MSW) - K53-8 (MIRS) | Always | Below 1 Ω |
| N25-7 (E) or K53-9 (MIRE) - Body ground | Always | 10 kΩ or higher |
| N25-4 (M+) or K53-7 (MIRB) - Body ground | Always | 10 kΩ or higher |
| N25-5 (MSW) or K53-8 (MIRS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG